RHRuslan Humeniuk

Ruslan Humeniuk

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ruslan Humeniuk has a total of 45 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Comparative Structural Response of Conventional and Hybrid Seat–Handrail Systems in a Low-Floor Urban Bus

    by Kostiantyn Holenko, Oleksandr Dykha, Anna PięTocha, Ivan Kernytskyy, Orest Horbay, Yuriy Royko, Taras Postranskyy, Andrii Sharybura, Ruslan Humeniuk, Vasyl Rys, et al.

    Integrating passenger seats with the load-bearing framework of low-floor urban buses changes seat-support connectivity and motivates comparison of alternative structural layouts. This study compares conventional floor-mounted seats with a hybrid seat–handrail system connected to both the floor and roof. Finite element analyses were performed using Ansys Explicit Dynamics for a simplified frontal impact at 30 km/h and Ansys Transient Structural for separate seat-back loading based on force prescriptions from UN Regulation No. 80 (R80). Tubular members were represented by beam elements, with common prescribed loading and boundary conditions used for each configuration pair. In the baseline force-based impact simulations, the hybrid configuration reduced peak seat-back displacements by 11.44% for the 1st seat and 1.90% for the 4th seat. The simulated peak structural backrest acceleration decreased from 10.2 g to 8.6 g. Under prescribed seat-back loading, peak Y-axis displacements of the upper backrest crossbars decreased from 518.71–518.72 mm to 51.12–55.99 mm, representing reductions of approximately 90% across the four seats. The comparison demonstrates that the structural influence of seat–handrail integration is strongly dependent on the loading scenario and seat location. These findings support further development of integrated seat-support layouts and investigation of attachment stiffness and load transfer.

  • Open Access

    Evaluation of Influence of the Integrated Welded Handrail System in the Bus Body Frame on Strength and Passive Safety

    by Kostyantyn Holenko, Eugeniusz Koda, Oleksandr Dykha, Ivan Kernytskyy, Orest Horbay, Marek Chalecki, Yuriy Royko, Ruslan Humeniuk, Andrii Sharybura, Yaroslav Sholudko, et al.

    Achieving the EU 2030 target of a 30% CO2 reduction requires transitioning intercity buses to CNG- or fuel-cell-driven vehicles, and urban buses to electric vehicles. The increasing mass of roof-mounted energy systems, such as battery packs, creates additional loads on the body frame. This study investigates the integration of a welded handrail system into the bus body frame as an additional load-bearing element. A combined approach based on dynamic modeling and finite element analysis was applied to evaluate the structural body response under the UNECE R100 and R110 regulations. The results demonstrate that the structural concept significantly improves the stress–strain state of the body frame. Maximum roof displacements under 5g loading decreased by 34% for the gas-powered model and by 50% for the electric model, enhancing passive safety by reducing window-rack intrusion. Maximum stress decreased by 20%, shifting the stress state below the ultimate strength of S235 steel and preventing rupture. Uniform strength under vertical loading increased significantly (by 58%) due to a more favorable stress distribution within the structure. Overall, the results indicate that integrating a welded handrail truss into the bus body frame can effectively improve structural stiffness and redistribute loads within the frame.


  • Open Access

    Improving the quality of petrol fuel for internal combustion engines

    by Ivan Aftanaziv, Liliya Shevchuk, Inga Svidrak, Nazarii Kernytskyy, Yuriy Royko, Serhii Berezovetskyi, Vasyl Rys, Ruslan Humeniuk, Yaroslav Sholudko, Kernytskyy Ivan

    The design of an automobile electromagnetic vibration cavitator created for the cavitation treatment of water-petrol fuel is described. Its use will allow not only saving fuel, but also increasing the completeness of combustion of the water-petrol fuel mixture; in other words, it will contribute to improving the environment. An experimental study of effectiveness of the fuel mixture cavitation treatment was carried out using A95 petrol and distilled water for automobile internal combustion engines. Cavitation treatment of the fuel mixture with a water-to-petrol ratio of 17 to 83% allows for an increase in the savings of expensive petrol by 15‒20% during the operation of engines on flat and downhill roads and in city traffic jams. At the same time, the engine power is reduced by only 6‒7% due to the cavitation treatment.


  • Open Access

    Peculiarities of Assessing Body Strength When Converting a Bus from Diesel to Electric Traction Following the UNECE R100 Regulation

    by Kostyantyn Holenko, Oleksandr Dykha, Eugeniusz Koda, Ivan Kernytskyy, Orest Horbay, Yuriy Royko, Ruslan Humeniuk, Yaroslav Sholudko, Vasyl Rys, Serhii Berezovetskyi, et al.

    The problem of the conversion of diesel buses to electric ones in connection with the inevitable introduction of the EURO 7 emission standards entails an automatic requirement to follow several additional United Nations Economic Commission for Europe rules, like R100 regulations. They regulate the preservation of battery units at longitudinal 12 g and transverse 10 g accelerations without penetrating into the elements of the bus body. Three models (12 modes in total) of battery units with frames made of S235 steel were analysed. The maximum stress value varies between 364.89 MPa and 439.08 MPa in 10 g and 12 g modes, respectively, which is beyond the tensile strength (360 MPa) and provokes plastic deformations. The max deformations were recorded in the models with the highest average stress: 63.04 mm in the 12 g mode with an average stress of 83.18 MPa. The minimum deformations of 6.95 and 7.95 mm were found in the 10 g modes (left and right acceleration direction, respectively), which meet the manufacturer’s requirements (45–50 mm maximum). The study’s primary contribution lies in developing a practical method for assessing battery unit integrity and structural behaviour during the conversion of diesel buses to electric propulsion, fully compliant with R100 regulations. By combining transient structural simulation, mathematical centre modelling of acceleration propagation, and centre of gravity prediction, the proposed approach enables engineers to evaluate electric conversions’ safety and certification feasibility without modifying the existing bus body.


  • Open Access

    Analysis Based on a Two-Dimensional Mathematical Model of the Thermo-Stressed State of a Copper Plate During Its Induction Heat Treatment

    by Roman Musii, Myroslava Klapchuk, Eugeniusz Koda, Ivan Kernytskyy, Inga Svidrak, Ruslan Humeniuk, Yaroslav Sholudko, Mykola Nagirniak, Joanna Andrzejak, Yuriy Royko

    A two-dimensional physical and mathematical model is proposed for determining the components of the stress tensor and stress intensity in an electroconductive plate of rectangular cross-section under the action of an unsteady electromagnetic field. The two-dimensional thermomechanics problem for such a plate is formulated. The determining functions are the component of the magnetic field intensity vector tangent to the plate bases, temperature, and components of the stress tensor. The methodology for solving the formulated thermomechanics problem by approximating all the determining functions by the thickness variable with cubic polynomials is developed. As a result, the original two-dimensional problems related to the determining functions are reduced to one-dimensional problems on the integral characteristics of these functions. To solve the obtained systems of equations for the integral characteristics of the determining functions, a finite integral transformation in the transverse variable is used. During induction heating of a copper plate by a homogeneous quasi-steady-state electromagnetic field, the change in the stress intensity depending on the Fourier time, as well as its distribution across the plate cross-section depending on the parameters of induction heating and the Biot criterion, is numerically analyzed.


  • Open Access

    Structure and Strength Optimization of the Bogdan ERCV27 Electric Garbage Truck Spatial Frame Under Static Loading

    by Kostyantyn Holenko, Oleksandr Dykha, Eugeniusz Koda, Ivan Kernytskyy, Orest Horbay, Yuriy Royko, Yevhen Fornalchyk, Oksana Berezovetska, Vasyl Rys, Ruslan Humenuyk, et al.

    Taking into account the requirements to reduce the release of harmful emissions into the environment, the EU’s environmental standards when transitioning to the Euro 7 standard in 2025 will actually lead vehicles having to operate without producing emissions in all driving situations. Carmakers believe that the new, much stricter regulations will mark the end of the internal combustion engine era. For example, in 2030, the manufacturer SEAT will cease its activities, leaving behind the Cupra brand, which will be exclusively electric in the future. This trend will apply not only to private vehicles (passenger cars), but also to utility vehicles, which is the subject of our research, namely the spatial tubular frame in the Bogdan ERCV27 garbage truck, presented in the form of a solid model. The peculiarity of the studied model is the installation of a battery block behind the driver’s cabin, causing an additional load to be placed on the spatial frame of the garbage truck, which in terms of its architecture is more like the body of a bus. During the conditions involving various modes of operation of a full-scale Bogdan ERCV27 garbage truck sample, questions about the strength and uniformity of its load-bearing spatial frame inevitably arise, which are decisive, even at the stage of designing and preparing the technical documentation. The main static load mode, which, despite its name, also covers dynamic conditions, was modeled using the appropriate coefficient kd = 2.0. The maximum stresses on the model during the “bending” mode were 381.13 MPa before structure optimization and 270.5 MPa as a result of the improvement measures. The spatial frame mass was reduced by 4.13%. During the “torsion” mode, the maximum deformation values were 12.1–14.5 mm, which guarantees the normal operation of the aggregates and units of the truck.


  • Open Access

    Validation of Frontal Crashworthiness Simulation for Low-Entry Type Bus Body According to UNECE R29 Requirements

    by Kostyantyn Holenko, Oleksandr Dykha, Eugeniusz Koda, Ivan Kernytskyy, Yuriy Royko, Orest Horbay, Oksana Berezovetska, Vasyl Rys, Ruslan Humenuyk, Serhii Berezovetskyi, et al.

    Frontal crash tests are an essential element in assessing vehicle safety. They simulate a collision that occurs when the front of the bus hits another vehicle or an obstacle. In recent years, much attention has been paid to the frontal crash testing of city buses, especially after a series of accidents resulting in deaths and injuries. Unlike car manufacturers, most bus bodybuilders do not include deformation zones in their designs. The next two regulations are widely used to assess whether a structure can withstand impact loading: UNECE Regulation No. 29—United Nations Economic Commission for Europe (UNECE R29) and the New Car Assessment Program (NCAP), which is more typical of car crash tests. The main goal of the research is to develop an applicable methodology for a frontal impact simulation on a city bus, considering UNECE R29 requirements for the passenger’s safety and distinctive features of the low-entry body layout. Among the contributions to current knowledge are such research results as: unlike suburban and intercity buses, city buses are characterized by lower stiffness in the event of a frontal collision, and therefore, when developing new models, it is necessary to lay deformation zones (currently absent from most city buses). Maximum deformation values in the bus front part are reached earlier for R29 (137 ms) than for most impacts tested by NCAP (170–230 ms) but have higher values: 577 mm vs. 150–250 mm for the sills tested. Such a short shock absorption time and high deformations indicate a significantly lighter front part of a low-entry and low-floor bus compared with classic layouts. Furthermore, it is unjustified to use the R29 boundary conditions of trucks to attach the bus with chains behind its frontal axe both in natural tests and appropriate finite element simulation—the scheme of fixing the city bus should be accordingly adapted and normatively revised.


  • Open Access

    Optimization of the semi-active vibration absorbers

    by Volodymyr Snitynskyy, Ivan Kernytskyy, Bohdan Diveyev, Orest Horbay, Yevhen Fornalchyk, Ruslan Humenuyk, Yaroslav Sholudko

    In this paper, an efficient numerical approach is proposed to maximize the minimal damping of modes in a prescribed frequency range for general viscous tuned-mass systems. Methods of decomposition and numerical synthesis are considered on the basis of the adaptive schemes. The influence of dynamic vibration absorbers and basic design elastic and damping properties is under discussion. A technique is developed to give the optimal DVA’s for the elimination of excessive vibration in sinusoidal and impact forced system. One task of this work is to analyze parameters identification of the dynamic vibration absorber and the basic structure. The questions of robustness at optimization of DVA are considered. Different types of control management for semi-active DVA’s are applied. Examples of DVA’s practical implementation are presented.

  • Modelling of artery stiffness for driver’s heart rate monitoring systems development

    by Ivan Kernytskyy, Orest Horbay, Ruslan Humenyuk, Yaroslav Sholudko, Yevhen Storchun, Yevheniia Yakovenko


  • Impact and particle vibration absorbers optimal design

    by Volodymyr Snitynskyy, Bohdan Diveyev, Orest Horbay, Ruslan Humenyuk, Ivan Kernytskyy, Tetiana Kokhana, Petro Koruniak