Patrick Mesmer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Patrick Mesmer has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Alexander Verl
University of Stuttgart
4 shared publications - Armin Lechler
Institute for Control Engineering of Machine Tools and Manufacturing Units (ISW), University of Stuttgart, Stuttgart, Germany
4 shared publications - Michael Neubauer
Montana State University
2 shared publications - Christoph Hinze
Institute for Control Engineering of Machine Tools and Manufacturing Units, University of Stuttgart, Stuttgart, Germany
1 shared publication Patrick Riedel
University of Stuttgart
1 shared publication
Latest Publications
- Open Access
- 11 July 2023
- Published by Springer Nature
- p. 177-187
Investigation and Compensation of Hysteresis in Robot Joints with Cycloidal Drives
Improving the dynamic path accuracy has been a major research topic in industrial robotics for decades. It is known that the drivetrains installed in the robot joints limit further improvements. There is a lot more literature on the dynamic behavior of harmonic drives (HDs) than for cycloidal drives (CDs), that are usually installed in industrial robots (IRs) with heavy payload. However, a more profound knowledge of the occurring effects offers the potential for both, design- and control-based enhancements. Therefore, this paper presents an experimental study of the friction and hysteresis behavior with explicit consideration of further dependencies, such as temperature and load. Based on these investigations, a model as well as a control-based compensation approach, that does not require additional gearbox output sensors, is proposed. The investigation and validation are carried out with an experimental setup equivalent to the drivetrain of an IR with heavy payload.
- 11 July 2023
- Published by Springer Nature
- p. 177-187
Open AccessInvestigation and Compensation of Hysteresis in Robot Joints with Cycloidal Drives
Improving the dynamic path accuracy has been a major research topic in industrial robotics for decades. It is known that the drivetrains installed in the robot joints limit further improvements. There is a lot more literature on the dynamic behavior of harmonic drives (HDs) than for cycloidal drives (CDs), that are usually installed in industrial robots (IRs) with heavy payload. However, a more profound knowledge of the occurring effects offers the potential for both, design- and control-based enhancements. Therefore, this paper presents an experimental study of the friction and hysteresis behavior with explicit consideration of further dependencies, such as temperature and load. Based on these investigations, a model as well as a control-based compensation approach, that does not require additional gearbox output sensors, is proposed. The investigation and validation are carried out with an experimental setup equivalent to the drivetrain of an IR with heavy payload.
- 1 February 2022
- Published by Elsevier in Robotics and Computer-Integrated Manufacturing
- Vol. 73
Robust design of independent joint control of industrial robots with secondary encoders
- 1 February 2022
- Published by Elsevier in Robotics and Computer-Integrated Manufacturing
- Vol. 73
Robust design of independent joint control of industrial robots with secondary encoders
- Open Access
- 28 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Gain-Scheduled Drive-based Damping Control for Industrial Robots
The drivetrain flexibility of industrial robots limits their accuracy. To open up new areas of application for industrial robots, an increased dynamic path accuracy has to be obtained. Therefore, this paper addresses this issue by a gain-scheduled drive-based damping control for industrial robots with secondary encoders. For this purpose, a linear parameter-varying (LPV) model is derived as well as a system identification method is presented. Based on this, a gain-scheduled drive-based LPV damping control design is proposed, which guarantees stability and performance under variation of the manipulator configuration. The control performance of the approach is experimentally validated for the three base joints of a KUKA KR210-2 industrial robot. The approach realizes a trade-off between ease of implementation and control performance as well as robustness.
- 28 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Open AccessGain-Scheduled Drive-based Damping Control for Industrial Robots
The drivetrain flexibility of industrial robots limits their accuracy. To open up new areas of application for industrial robots, an increased dynamic path accuracy has to be obtained. Therefore, this paper addresses this issue by a gain-scheduled drive-based damping control for industrial robots with secondary encoders. For this purpose, a linear parameter-varying (LPV) model is derived as well as a system identification method is presented. Based on this, a gain-scheduled drive-based LPV damping control design is proposed, which guarantees stability and performance under variation of the manipulator configuration. The control performance of the approach is experimentally validated for the three base joints of a KUKA KR210-2 industrial robot. The approach realizes a trade-off between ease of implementation and control performance as well as robustness.
- 19 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 5 (2) , 564-571
Drive-Based Vibration Damping Control for Robot Machining
The objective of this letter is to propose a drive-based control method for damping joint vibrations in order to improve the machining quality and the productivity of robot machining. The machining quality is significantly determined by the transfer behavior of the gearboxes installed in the robot joints. This letter presents a novel approach for drive-based damping of these vibrations and thus for increasing the dynamic path accuracy on the basis of secondary encoders. The approach represents an enhancement of the independent joint control, which is widely used in industry. The simulation as well as the experimental results on a KUKA KR210-2 demonstrate the effectiveness of the presented control method for damping gearbox vibrations and increasing the dynamic path accuracy of industrial robot manipulators.
- 19 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 5 (2) , 564-571
Drive-Based Vibration Damping Control for Robot Machining
The objective of this letter is to propose a drive-based control method for damping joint vibrations in order to improve the machining quality and the productivity of robot machining. The machining quality is significantly determined by the transfer behavior of the gearboxes installed in the robot joints. This letter presents a novel approach for drive-based damping of these vibrations and thus for increasing the dynamic path accuracy on the basis of secondary encoders. The approach represents an enhancement of the independent joint control, which is widely used in industry. The simulation as well as the experimental results on a KUKA KR210-2 demonstrate the effectiveness of the presented control method for damping gearbox vibrations and increasing the dynamic path accuracy of industrial robot manipulators.