Fatih Apaydin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Fatih Apaydin has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Kenan Yildiz
Sakarya University
2 shared publications A Atasoy
1 shared publication- Ahmet Ferdi Şenol
Department of Civil Engineering, Faculty of Engineering, Bilecik Şeyh Edebali University, Bilecik, Turkey
1 shared publication - Ali Ozer
Department of Materials Science and Engineering University of Illinois at Urbana‐Champaign Urbana Illinois USA
1 shared publication - Ali Çelik1 shared publication
- Ali Çeli̇k
Bilecik Şeyh Edebali Üniversitesi
1 shared publication
Latest Publications
- Open Access
- 21 July 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Enhancement of thiourea leaching performance of refractory silver tailings by mechanical activation
Refractory silver tailings are both an environmental liability and a potential secondary resource for precious metals. However, strong mineralogical locking of silver-bearing phases within barite and aluminosilicate matrices severely limits silver recovery under conventional leaching conditions. In this study, mechanical activation was investigated as a pretreatment method to enhance the thiourea leaching performance of refractory silver tailings from the Kütahya Eti Silver Plant (Turkey). Mechanical activation was carried out in a planetary ball mill for 0, 30, 60, and 90 min. The resulting changes in particle size, specific surface area, and structure were evaluated by particle size analysis, BET, XRD, and SEM. Mechanical activation caused marked particle fragmentation, increased surface area, and partial amorphization, indicating enhanced structural disorder and improved accessibility of silver-bearing phases. Thiourea leaching experiments were performed using 0.5 M thiourea in acidic solution at pH 1.5, with 0.01 M ferric sulfate as the oxidizing agent. Under the optimum conditions identified in this study, namely 90 min mechanical activation, 50 °C, S/L = 1/10, and 600 rpm, silver recovery increased from about 68% for the non-activated sample to about 96% for the mechanically activated sample. Kinetic analysis under conditions minimizing external mass-transfer resistance showed that apparent rate constants increased with activation time, while the apparent activation energy decreased from 46.1 to 38.9 kJ·mol −1 . Post-leaching SEM and BET results revealed agglomerated and porous particle structures, indicating that diffusion through evolving porous particle assemblies contributes to the observed kinetic behavior. This work directly links mechanochemically induced structural evolution with apparent leaching kinetics in industrial refractory silver tailings and highlights mechanically assisted thiourea leaching as a promising cyanide-free alternative for refractory silver-bearing wastes.
- 21 July 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open AccessEnhancement of thiourea leaching performance of refractory silver tailings by mechanical activation
Refractory silver tailings are both an environmental liability and a potential secondary resource for precious metals. However, strong mineralogical locking of silver-bearing phases within barite and aluminosilicate matrices severely limits silver recovery under conventional leaching conditions. In this study, mechanical activation was investigated as a pretreatment method to enhance the thiourea leaching performance of refractory silver tailings from the Kütahya Eti Silver Plant (Turkey). Mechanical activation was carried out in a planetary ball mill for 0, 30, 60, and 90 min. The resulting changes in particle size, specific surface area, and structure were evaluated by particle size analysis, BET, XRD, and SEM. Mechanical activation caused marked particle fragmentation, increased surface area, and partial amorphization, indicating enhanced structural disorder and improved accessibility of silver-bearing phases. Thiourea leaching experiments were performed using 0.5 M thiourea in acidic solution at pH 1.5, with 0.01 M ferric sulfate as the oxidizing agent. Under the optimum conditions identified in this study, namely 90 min mechanical activation, 50 °C, S/L = 1/10, and 600 rpm, silver recovery increased from about 68% for the non-activated sample to about 96% for the mechanically activated sample. Kinetic analysis under conditions minimizing external mass-transfer resistance showed that apparent rate constants increased with activation time, while the apparent activation energy decreased from 46.1 to 38.9 kJ·mol −1 . Post-leaching SEM and BET results revealed agglomerated and porous particle structures, indicating that diffusion through evolving porous particle assemblies contributes to the observed kinetic behavior. This work directly links mechanochemically induced structural evolution with apparent leaching kinetics in industrial refractory silver tailings and highlights mechanically assisted thiourea leaching as a promising cyanide-free alternative for refractory silver-bearing wastes.
- 31 May 2026
- Published by Bilecik Seyh Edebali Universitesi Fen Bilimleri Dergisi in Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi
- Vol. 13 (1) , 80-90
Küresel Grafitli Dökme Demirde SiC ve FeSi Katkılarının Mikroyapı, Sertlik ve Üretim Maliyeti Üzerindeki Etkileri
Bu araştırma, küresel grafitli dökme demir (KGDD) üretim sürecinde kullanılan silisyum karbür (SiC) ve ferro silisyum (FeSi) katkı malzemelerinin mikroyapısal karakteristikleri, mekanik performansları ve üretim maliyetleri üzerindeki etkilerini karşılaştırmalı olarak değerlendirmektedir. GGG40 sınıfı numuneler endüstriyel ergitme ve döküm süreçleriyle hazırlanmış, ardından çekme testi, sertlik ölçümü ve mikroyapı analizleri gerçekleştirilmiştir. SiC katkısı, daha homojen grafit dağılımı, yüksek sertlik ve düşük üretim maliyeti ile öne çıkarken; FeSi katkısı daha yüksek uzama ve ferritik-perlitik denge sunmuştur. Her iki katkı benzer çekme mukavemeti sağlasa da SiC teknik ve ekonomik açıdan daha avantajlı bir alternatif olarak değerlendirilmiştir.
- 31 May 2026
- Published by Bilecik Seyh Edebali Universitesi Fen Bilimleri Dergisi in Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi
- Vol. 13 (1) , 80-90
Küresel Grafitli Dökme Demirde SiC ve FeSi Katkılarının Mikroyapı, Sertlik ve Üretim Maliyeti Üzerindeki Etkileri
Bu araştırma, küresel grafitli dökme demir (KGDD) üretim sürecinde kullanılan silisyum karbür (SiC) ve ferro silisyum (FeSi) katkı malzemelerinin mikroyapısal karakteristikleri, mekanik performansları ve üretim maliyetleri üzerindeki etkilerini karşılaştırmalı olarak değerlendirmektedir. GGG40 sınıfı numuneler endüstriyel ergitme ve döküm süreçleriyle hazırlanmış, ardından çekme testi, sertlik ölçümü ve mikroyapı analizleri gerçekleştirilmiştir. SiC katkısı, daha homojen grafit dağılımı, yüksek sertlik ve düşük üretim maliyeti ile öne çıkarken; FeSi katkısı daha yüksek uzama ve ferritik-perlitik denge sunmuştur. Her iki katkı benzer çekme mukavemeti sağlasa da SiC teknik ve ekonomik açıdan daha avantajlı bir alternatif olarak değerlendirilmiştir.
- Open Access
- 7 April 2026
- Published by Springer Nature in Journal of the Australian Ceramic Society
- Vol. 62 (5) , 2075-2090
Electrodeposited Ag–TiB₂ nanocomposite coatings for electrical contact applications: influence of TiB₂ content and current type on arc erosion resistance and mechanical properties
This study investigates the influence of titanium diboride (TiB₂) nanoparticle content on the microstructure, mechanical properties, corrosion behavior, and electrical contact performance of electrodeposited silver (Ag) nanocomposite coatings applied to copper contact buttons. Ag–TiB₂ nanocomposite coatings were fabricated via direct current (DC) electrodeposition using electrolytes containing 0.5, 1.0, 2.0, and 4.0 g/L TiB₂. The coatings were systematically characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), energy-dispersive spectroscopy (EDS), Vickers microhardness testing, corrosion measurements, and electrical contact testing. The incorporation of TiB₂ nanoparticles refined the grain structure, increased hardness, enhanced corrosion resistance, and improved arc erosion behavior. Among the coatings, the one with 1.0 g/L TiB₂ exhibited the most favorable combination of surface compactness, hardness, corrosion protection, and thermal stability under high cycle contact testing. Electrical contact tests conducted up to 10,000 cycles showed reduced erosion and lower surface temperatures compared to unreinforced Ag coatings. However, TiB₂ concentrations beyond 1.0 g/L led to nanoparticle agglomeration, increased surface roughness, and reduced long-term performance in both contact and corrosion environments. These findings demonstrate that the controlled incorporation of TiB₂ nanoparticles into Ag matrices via DC electrodeposition significantly enhances the multifunctional performance of contact coatings, offering a promising cadmium-free solution for high-reliability electrical switching components. Among the investigated compositions, the Ag–TiB₂ coating containing 1.0 g/L TiB₂ exhibited the optimum balance of mechanical, electrical, and corrosion performance, highlighting its suitability as an effective cadmium-free electrical contact coating.
- 7 April 2026
- Published by Springer Nature in Journal of the Australian Ceramic Society
- Vol. 62 (5) , 2075-2090
Open AccessElectrodeposited Ag–TiB₂ nanocomposite coatings for electrical contact applications: influence of TiB₂ content and current type on arc erosion resistance and mechanical properties
This study investigates the influence of titanium diboride (TiB₂) nanoparticle content on the microstructure, mechanical properties, corrosion behavior, and electrical contact performance of electrodeposited silver (Ag) nanocomposite coatings applied to copper contact buttons. Ag–TiB₂ nanocomposite coatings were fabricated via direct current (DC) electrodeposition using electrolytes containing 0.5, 1.0, 2.0, and 4.0 g/L TiB₂. The coatings were systematically characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), energy-dispersive spectroscopy (EDS), Vickers microhardness testing, corrosion measurements, and electrical contact testing. The incorporation of TiB₂ nanoparticles refined the grain structure, increased hardness, enhanced corrosion resistance, and improved arc erosion behavior. Among the coatings, the one with 1.0 g/L TiB₂ exhibited the most favorable combination of surface compactness, hardness, corrosion protection, and thermal stability under high cycle contact testing. Electrical contact tests conducted up to 10,000 cycles showed reduced erosion and lower surface temperatures compared to unreinforced Ag coatings. However, TiB₂ concentrations beyond 1.0 g/L led to nanoparticle agglomeration, increased surface roughness, and reduced long-term performance in both contact and corrosion environments. These findings demonstrate that the controlled incorporation of TiB₂ nanoparticles into Ag matrices via DC electrodeposition significantly enhances the multifunctional performance of contact coatings, offering a promising cadmium-free solution for high-reliability electrical switching components. Among the investigated compositions, the Ag–TiB₂ coating containing 1.0 g/L TiB₂ exhibited the optimum balance of mechanical, electrical, and corrosion performance, highlighting its suitability as an effective cadmium-free electrical contact coating.
- Open Access
- 28 February 2026
- Published by Elsevier in SSRN Electronic Journal
Enhancement of Thiourea Leaching Performance of Refractory Silver Tailings by Mechanical Activation
Mechanical activation was investigated as a pretreatment strategy to enhance thiourea leaching of refractory silver tailings obtained from the Kütahya Eti Silver Plant (Turkey). The tailings exhibit strong mineralogical locking of silver-bearing phases within barite and aluminosilicate matrices, resulting in low recoveries under conventional leaching conditions. Mechanical activation was applied for 0, 30, 60, and 90 min using a planetary ball mill, and its effects on particle size distribution, specific surface area, amorphization degree, and microstructure were systematically evaluated.Thiourea leaching experiments were conducted in acidic media (pH 1.5) with Fe³⁺ as the oxidizing agent. Mechanical activation significantly improved silver dissolution, increasing recovery from approximately 68% for the non-activated sample to about 96% after 90 min of activation at 50 °C. The enhancement is attributed to particle size reduction, defect generation, partial amorphization, and improved reagent accessibility to silver-bearing phases.Kinetic evaluation under minimized external mass-transfer resistance showed a marked increase in apparent rate constants with increasing activation time, accompanied by a progressive decrease in apparent activation energy from 46.1 kJ·mol⁻¹ (non-activated) to 42.99, 40.13, and 38.9 kJ·mol⁻¹ for 30, 60, and 90 min activated samples, respectively. Post-leaching SEM and BET analyses revealed agglomeration and porous structure development, indicating diffusion-influenced transport within evolving particle assemblies. Overall, the results establish a physically consistent link between mechanochemically induced structural disorder and apparent leaching kinetics, highlighting mechanical activation as an effective cyanide-free pretreatment for refractory silver tailings.
- 28 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEnhancement of Thiourea Leaching Performance of Refractory Silver Tailings by Mechanical Activation
Mechanical activation was investigated as a pretreatment strategy to enhance thiourea leaching of refractory silver tailings obtained from the Kütahya Eti Silver Plant (Turkey). The tailings exhibit strong mineralogical locking of silver-bearing phases within barite and aluminosilicate matrices, resulting in low recoveries under conventional leaching conditions. Mechanical activation was applied for 0, 30, 60, and 90 min using a planetary ball mill, and its effects on particle size distribution, specific surface area, amorphization degree, and microstructure were systematically evaluated.Thiourea leaching experiments were conducted in acidic media (pH 1.5) with Fe³⁺ as the oxidizing agent. Mechanical activation significantly improved silver dissolution, increasing recovery from approximately 68% for the non-activated sample to about 96% after 90 min of activation at 50 °C. The enhancement is attributed to particle size reduction, defect generation, partial amorphization, and improved reagent accessibility to silver-bearing phases.Kinetic evaluation under minimized external mass-transfer resistance showed a marked increase in apparent rate constants with increasing activation time, accompanied by a progressive decrease in apparent activation energy from 46.1 kJ·mol⁻¹ (non-activated) to 42.99, 40.13, and 38.9 kJ·mol⁻¹ for 30, 60, and 90 min activated samples, respectively. Post-leaching SEM and BET analyses revealed agglomeration and porous structure development, indicating diffusion-influenced transport within evolving particle assemblies. Overall, the results establish a physically consistent link between mechanochemically induced structural disorder and apparent leaching kinetics, highlighting mechanical activation as an effective cyanide-free pretreatment for refractory silver tailings.
- Open Access
- 26 May 2025
- Published by Springer Nature in Journal of the Australian Ceramic Society
- Vol. 61 (5) , 1837-1851
The effect of cupola furnace iron slag on the physical and mechanical properties of alkali-activated fly ash-based mortars
This study investigates the physical and mechanical properties of alkali-activated mortars, in which thermal power plant fly ash (FA) was partially replaced by cupola furnace iron slag (IS). An optimal mix design determined through preliminary tests consisted of an aggregate-to-binder ratio of 1.5 (by weight), NaOH solution concentration of 10 M, Na₂SiO₃ (liquid) to NaOH (solid) ratio of 2, and a water-to-binder ratio of 0.3, all maintained consistently across mixtures. Chemical compositions and phase structures of raw materials were characterized using X-ray fluorescence (XRF) and X-ray diffraction (XRD), respectively. Particle size distribution was determined by laser diffraction analysis, and microstructural morphology was examined using scanning electron microscopy (SEM). Bulk density and apparent porosity were measured using Archimedes’ method with water as the immersion medium. Mechanical properties were evaluated through compressive strength and three-point bending tests after 28 days of curing. Results showed that mortars incorporating 75 wt% cupola furnace iron slag as a fly ash replacement exhibited superior performance, achieving a bulk density of 2118 kg/m³, apparent porosity of 12.2%, compressive strength of 44 MPa, and flexural strength of 10.2 MPa. These findings highlight the potential of iron slag as an effective supplementary material in alkali-activated mortars, enhancing mechanical properties and contributing to microstructural densification.
- 26 May 2025
- Published by Springer Nature in Journal of the Australian Ceramic Society
- Vol. 61 (5) , 1837-1851
Open AccessThe effect of cupola furnace iron slag on the physical and mechanical properties of alkali-activated fly ash-based mortars
This study investigates the physical and mechanical properties of alkali-activated mortars, in which thermal power plant fly ash (FA) was partially replaced by cupola furnace iron slag (IS). An optimal mix design determined through preliminary tests consisted of an aggregate-to-binder ratio of 1.5 (by weight), NaOH solution concentration of 10 M, Na₂SiO₃ (liquid) to NaOH (solid) ratio of 2, and a water-to-binder ratio of 0.3, all maintained consistently across mixtures. Chemical compositions and phase structures of raw materials were characterized using X-ray fluorescence (XRF) and X-ray diffraction (XRD), respectively. Particle size distribution was determined by laser diffraction analysis, and microstructural morphology was examined using scanning electron microscopy (SEM). Bulk density and apparent porosity were measured using Archimedes’ method with water as the immersion medium. Mechanical properties were evaluated through compressive strength and three-point bending tests after 28 days of curing. Results showed that mortars incorporating 75 wt% cupola furnace iron slag as a fly ash replacement exhibited superior performance, achieving a bulk density of 2118 kg/m³, apparent porosity of 12.2%, compressive strength of 44 MPa, and flexural strength of 10.2 MPa. These findings highlight the potential of iron slag as an effective supplementary material in alkali-activated mortars, enhancing mechanical properties and contributing to microstructural densification.
- Open Access
- 31 December 2023
- Published by Orclever Science and Research Group in Orclever Proceedings of Research and Development
- Vol. 3 (1) , 158-170
Investigation of Suitable Production Conditions of High Extension Cast Iron (EN-GJS-400-18)
EN-GJS-400-18 spherical cast iron materials are widely used in the automotive, construction, mining, metallurgy, and machinery manufacturing sectors due to their high strength, ductility, toughness, low melting point, good fluidity, and good machinability properties. There are various difficulties in always producing at the same standard under mass production conditions. The most important of these difficulties is the lack of availability of raw materials of the same purity. In this study, it is aimed to produce EN-GJS-400-18 ductile iron material, which is difficult to produce in terms of mass production practice in foundries, in accordance with serial conditions. For this purpose, the effects of Si, carbide-forming elements Cu and Mo, and casting material diameter on the microstructure and mechanical properties of EN-GJS-400-18 spherical graphite cast iron were examined. As a result of the experiments, it was seen that the 20 mm diameter sample with the content of %Si:3.10, %Mo:0.001, %Cu:0.03 was obtained with the highest elongation value of 22.38%. It has been determined that the minimum ferrite ratio in the microstructure of this material is 80% and the number of nodules per mm2 is 600, which will reveal superior mechanical properties.
- 31 December 2023
- Published by Orclever Science and Research Group in Orclever Proceedings of Research and Development
- Vol. 3 (1) , 158-170
Open AccessInvestigation of Suitable Production Conditions of High Extension Cast Iron (EN-GJS-400-18)
EN-GJS-400-18 spherical cast iron materials are widely used in the automotive, construction, mining, metallurgy, and machinery manufacturing sectors due to their high strength, ductility, toughness, low melting point, good fluidity, and good machinability properties. There are various difficulties in always producing at the same standard under mass production conditions. The most important of these difficulties is the lack of availability of raw materials of the same purity. In this study, it is aimed to produce EN-GJS-400-18 ductile iron material, which is difficult to produce in terms of mass production practice in foundries, in accordance with serial conditions. For this purpose, the effects of Si, carbide-forming elements Cu and Mo, and casting material diameter on the microstructure and mechanical properties of EN-GJS-400-18 spherical graphite cast iron were examined. As a result of the experiments, it was seen that the 20 mm diameter sample with the content of %Si:3.10, %Mo:0.001, %Cu:0.03 was obtained with the highest elongation value of 22.38%. It has been determined that the minimum ferrite ratio in the microstructure of this material is 80% and the number of nodules per mm2 is 600, which will reveal superior mechanical properties.
- 28 March 2022
- Published by Springer Nature in Journal of the Australian Ceramic Society
- Vol. 58 (3) , 831-839
Comparison of electrical properties of ZnO-Bi2O3-based ceramics prepared by conventional and spark plasma sintering (SPS) methods
- 28 March 2022
- Published by Springer Nature in Journal of the Australian Ceramic Society
- Vol. 58 (3) , 831-839
Comparison of electrical properties of ZnO-Bi2O3-based ceramics prepared by conventional and spark plasma sintering (SPS) methods
- 26 December 2019
- Published by Bilecik Seyh Edebali Universitesi Fen Bilimleri Dergisi in Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi
- Vol. 6 (2) , 415-423
Nadir Toprak Elementi İlaveli ZnO-Esaslı Varistörlerin Elektriksel Özelliklerinin Karşılaştırılması
ZnO esaslı varistörler sahip oldukları doğrusal olmayan akım-voltaj (I-V) özelliği ile elektronik devreleri ve devre elemanlarını voltaj dalgalanmalarına karşı korumaktadır. Doğrusal olmayan I-V özelliği sayesinde varistörler farklı voltaj değerlerinde farklı direnç gösterir. Varistörlerde kırılma voltajı olarak belirtilen kritik voltaj değeri aşıldığı takdirde, varistör daha iletken hale gelerek oluşan yüksek akımı kendi üzerinden geçirerek devreyi koruyan sigorta görevi görür. Bu çalışmada ZnO-Bi2O3 esasla varistörlere çeşitli nadir toprak elementi katkısının (Y2O3, Er2O3, Sm2O3, La2O3, Yb2O3) mikroyapısal ve elektriksel özelliklerine etkileri karşılaştırılmıştır. % 98,5 mol ZnO, % 1 mol Bi2O3, % 0,5 mol (Y2O3, Er2O3, Sm2O3, La2O3, Yb2O3) komposizyonunda beş farklı varistör hazırlanmıştır. Bu kompozisyonlarda hazırlanan numuneler 1100°C’de 10 °C/dk ısıtma/soğutma hızında 1 saat sinterlenmiştir. Sonrasında hazırlanan varistörlerin mikroyapısal ve elektriksel özellikleri incelenmiştir. Yapılan analiz ve hesaplamalar sonucunda en küçük tane boyutu (4μm) La2O3 katkılı varistörde, en büyük tane boyutu (6,66 μm) Y2O3 katlı varistörde gerçekleşmiştir. Üretilen varistörlerin kırılma voltajı ( Eb) büyükten küçüğe doğru sırasıyla C, D, B, A ve E kodlu numunelerde 149, 142, 116, 114 ve 28 volt/mm olarak ölçülmüştür.
- 26 December 2019
- Published by Bilecik Seyh Edebali Universitesi Fen Bilimleri Dergisi in Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi
- Vol. 6 (2) , 415-423
Nadir Toprak Elementi İlaveli ZnO-Esaslı Varistörlerin Elektriksel Özelliklerinin Karşılaştırılması
ZnO esaslı varistörler sahip oldukları doğrusal olmayan akım-voltaj (I-V) özelliği ile elektronik devreleri ve devre elemanlarını voltaj dalgalanmalarına karşı korumaktadır. Doğrusal olmayan I-V özelliği sayesinde varistörler farklı voltaj değerlerinde farklı direnç gösterir. Varistörlerde kırılma voltajı olarak belirtilen kritik voltaj değeri aşıldığı takdirde, varistör daha iletken hale gelerek oluşan yüksek akımı kendi üzerinden geçirerek devreyi koruyan sigorta görevi görür. Bu çalışmada ZnO-Bi2O3 esasla varistörlere çeşitli nadir toprak elementi katkısının (Y2O3, Er2O3, Sm2O3, La2O3, Yb2O3) mikroyapısal ve elektriksel özelliklerine etkileri karşılaştırılmıştır. % 98,5 mol ZnO, % 1 mol Bi2O3, % 0,5 mol (Y2O3, Er2O3, Sm2O3, La2O3, Yb2O3) komposizyonunda beş farklı varistör hazırlanmıştır. Bu kompozisyonlarda hazırlanan numuneler 1100°C’de 10 °C/dk ısıtma/soğutma hızında 1 saat sinterlenmiştir. Sonrasında hazırlanan varistörlerin mikroyapısal ve elektriksel özellikleri incelenmiştir. Yapılan analiz ve hesaplamalar sonucunda en küçük tane boyutu (4μm) La2O3 katkılı varistörde, en büyük tane boyutu (6,66 μm) Y2O3 katlı varistörde gerçekleşmiştir. Üretilen varistörlerin kırılma voltajı ( Eb) büyükten küçüğe doğru sırasıyla C, D, B, A ve E kodlu numunelerde 149, 142, 116, 114 ve 28 volt/mm olarak ölçülmüştür.
- Open Access
- 1 December 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126330
Low temperature formation of barium titanate in solid state reaction by mechanical activation of BaCO3 and TiO2
- 1 December 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126330
Open AccessLow temperature formation of barium titanate in solid state reaction by mechanical activation of BaCO3 and TiO2
- 2 February 2018
- Published by Politeknik Dergisi in Journal of Polytechnic
Study on Solubility of Malachite Ore From Yozgat Region in Ammonium Nitrate Solution
- 2 February 2018
- Published by Politeknik Dergisi in Journal of Polytechnic
Study on Solubility of Malachite Ore From Yozgat Region in Ammonium Nitrate Solution