Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ying Zhang has a total of 30 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Degradation Characteristics of Coal Samples Under the Dry–Wet Cycle Action of Acidic, High-Salinity Solutions: Experimental Study and Fractal Analysis

    by Leiming Zhang, Min Wang, Bin Zhang, Xun Xi, Ying Zhang, Jiliang Pan

    Uniaxial compression tests were conducted on coal samples subjected to different dry–wet cycling treatments to investigate the damage and degradation mechanisms of coal samples under the dry–wet cyclic action of acidic, high-salinity solutions. The damage process of the coal samples was monitored in situ using acoustic emission (AE). The degradation evolution of the mechanical parameters and macroscopic failure modes with the number of cycles was analyzed. Based on the AE ringing parameters, the RA-AF distribution and the AE fractal dimension’s variation characteristics were studied. Additionally, scanning electron microscopy (SEM) was used to observe the microstructure of the coal samples. The results showed that with the increase in the number of dry–wet cycles, both the peak strength and elastic modulus of the coal samples exhibited varying degrees of degradation, and the failure mode gradually shifted from tensile failure to shear failure. AE ringing counts decreased progressively, while the proportion of shear cracks based on the RA-AF classification increased. At the same time, the mean AE fractal dimension of the coal samples increased, and the fractal dimension decreased with an increase in AE ringing counts. The sharp drop in fractal dimensions could serve as an early warning signal for a major failure in the coal samples. Furthermore, under the influence of dry–wet cycling in acidic, high-salinity solutions, defects such as pores and cracks in the microstructure of the coal samples became more pronounced, and the degradation effect continuously intensified.


  • Open Access

    Mechanical, Seepage, and Energy Evolution Properties of Multi-Shaped Fractured Sandstone Under Hydro-Mechanical Coupling: An Experimental Study

    by Ying Zhang, Kai He, Jianming Yang, Jiliang Pan, Xun Xi, Xianhui Feng, Leiming Zhang

    Rocks with multi-shaped fractures in engineering activities like mining, underground energy storage, and hydropower construction are often exposed to environments where stress and seepage fields interact, which heightens the uncertainty of instability and failure mechanisms. This has long been a long-standing challenge in the field of rock mechanics. Current research mainly focuses on the mechanical behavior, seepage, and energy evolution characteristics of single-fractured rocks under hydro-mechanical coupling. However, studies on the effects of multi-shaped fractures (such as T-shaped fractures, Y-shaped fractures, etc.) on these characteristics under hydro-mechanical coupling are relatively scarce. This study aims to provide new insights into this field by conducting hydro-mechanical coupling tests on multi-shaped fractured sandstones (single fractures, T-shaped fractures, Y-shaped fractures) with different inclination angles. The results show that hydro-mechanical coupling significantly reduces the peak strength, damage stress, crack initiation stress, and closure stress of fractured sandstone. The permeability jump factor (ξ) demonstrates the permeability enhancement effects of different fracture shapes. The ξ values for single fractures, T-shaped fractures, and Y-shaped fractures are all less than 2, indicating that fracture shape has a relatively minor impact on permeability enhancement. Fracture inclination and shape significantly affect the energy storage capacity of the rock mass, and the release of energy exhibits a nonlinear relationship with fracture propagation. An in-depth analysis of energy evolution characteristics under the influence of fracture shape and inclination reveals the transition pattern of the dominant role of energy competition in the progressive failure process. Microstructural analysis of fractured sandstone shows that elastic energy primarily drives fracture propagation and the elastic deformation of grains, while dissipative energy promotes particle fragmentation, grain boundary sliding, and plastic deformation, leading to severe grain breakage. The study provides important theoretical support for understanding the failure mechanisms of multi-shaped fractured sandstone under hydro-mechanical coupling.


  • Open Access

    Effect of Thermal Cracking on the Tensile Strength of Granite: Novel Insights into Numerical Simulation and Fractal Dimension

    by Jiliang Pan, Leiming Zhang, Yichen Ma, Ying Zhang, Xun Xi

    This study investigates the effect of thermal cracking on the tensile strength of granite through a combination of experimental testing and numerical simulations. The primary objective is to understand how thermal stress, induced by heat treatment at various temperatures (25 °C to 600 °C), influences crack initiation, propagation, and tensile strength changes. The granite specimens were subjected to Brazilian splitting tests after heat treatment, and the load–displacement curves and tensile strength variations with heat treatment temperature were analyzed. A grain-based model (GBM) was developed to simulate the complex cracking behavior, incorporating the mineral compositions and thermal expansion properties of the granite. The fractal dimension of the cracks was quantified using the box-counting method, and the relationship between fractal dimension and tensile strength was discussed. The results show that the GBM can effectively simulate the microcracking behavior and tensile fracture properties of heat-treated granite, accounting for mineral composition and thermal expansion. Thermal cracks are mainly intergranular tensile cracks, which increase in number with higher temperatures, while under mechanical loading failure is primarily due to intragranular tensile cracks. Higher heat treatment temperatures lead to denser crack networks with greater fractal complexity, reducing tensile strength and creating more tortuous crack propagation paths.


  • Open Access

    Effect of Chemical Corrosion on Rock Fracture Behavior in Coastal Deep Mines: Insights from Mechanical and Acoustic Characteristics

    by Jiliang Pan, Yichen Ma, Leiming Zhang, Zegong Ning, Ying Zhang, Xun Xi

    The demand for critical minerals has increased extraction activities in coastal deep mines where challenges such as high stresses, chemical corrosion, and mining disturbance impacts are present. This study investigated the effects of chemical corrosion and confining pressure on the mechanical and fracture behaviors of granite specimens, which are crucial for ensuring the stability of surrounding rock in coastal deep mines. Triaxial compression tests were conducted on uncorroded specimens and corroded specimens immersed in acid and alkali solutions under varying confining pressures, with real-time acoustic emission (AE) monitoring. Based on the test results, the strength and deformation properties, progressive fracture, and failure processes, as well as the AE response characteristics of the specimens under chemical corrosion and confining pressure were analyzed. Additionally, the influence of confining pressure on the chemical damage and brittle–ductile transition behavior of specimens was discussed, and the mechanism of chemical corrosion on the physical and mechanical behavior of specimens was revealed based on mineralogical analysis. These findings underscore the importance of understanding the interplay between chemical corrosion, confining pressure, and rock fracture behavior in coastal deep mining and contribute to evaluating the stability of underground surrounding rocks under corrosion environments.


  • Open Access

    Study on Hydro-Mechanical Coupling Failure and Permeability Enhancement Mechanisms for Sandstone with T-Shaped Fractures

    by Ying Zhang, Kun Bi, Jiliang Pan, Xun Xi, Dongsheng Zhang, Shengjun Miao, Meifeng Cai

    The rise in the connectivity of the fractures is a key task in oil/gas and geothermal exploitation systems. Natural fractures widely exist in underground reservoir sandstone, while the mechanical behavior of rock with fractures subjected to hydro-mechanical coupling loads is far from clear. This paper employed comprehensive experiments and numerical simulations to investigate the failure mechanism and permeability law for sandstone specimens with T-shaped faces subjected to hydro-mechanical coupling loads. The effects of crack closure stress, crack initiation stress, strength, and axial strain stiffness of the specimens under different fracture inclination angles are discussed, and the evolution processes of permeability are obtained. The results show that secondary fractures are created around the pre-existing T-shaped fractures through tensile, shear, or mixed modes. The fracture network causes an increase in the permeability of the specimen. T-shaped fractures have a more significant effect on the strength of the specimens than water. The peak strengths of T-shaped specimens decreased by 34.89%, 33.79%, 46.09%, 39.32%, 47.23%, 42.76%, and 36.02%, respectively, compared with intact specimen without water pressure. With the increase in deviatoric stress, the permeability of T-shaped sandstone specimens decreases first, then increases, reaching its maximum value when macroscopic fractures are formed, after which the stress suddenly decreases. When the prefabricated T-shaped fracture angle is 75°, the corresponding permeability of the sample at failure is maximum, with a value of 15.84 × 10−16 m2. The failure process of the rock is reproduced through numerical simulations, in which the influence of damage and macroscopic fractures on permeability is discussed.


  • Open Access

    A Negative Value of the Non-Darcy Flow Coefficient in Pore-Fracture Media under Hydro-Mechanical Coupling

    by Ying Zhang, Qingqing Shang, Dongsheng Zhang, Jiliang Pan, Xun Xi, Peitao Wang, Meifeng Cai

    The Forchheimer equation is widely used in studying non-Darcy flow. Non-Darcy flow coefficient β in the Forchheimer equation is generally thought to be positive, and there are few studies on negative values. In this work, we performed seepage tests on sandstone samples with single, T-shaped, and Y-shaped fractures under different confining pressures, water pressures, and angles to analyze the nonlinear seepage behaviors and the features of Forchheimer’s coefficients of water flow in pore-fracture media. At the same time, the flow trajectory of the fluid inside the sample is studied by numerical simulation. The results showed that β was negative in the seepage test in pore-fracture media. The angle of the single-fracture sandstone sample had a greater influence on the seepage characteristic of the pore-fracture media; angles of the sandstone samples with T-shaped and Y-shaped fractures had a relatively small impact. The relationship between β and inherent permeability k was following a power function, and the differences in the seepage characteristics between the three fractures were compared. The use of the normalized hydraulic conductivity method is used to evaluate the applicability of Darcy’s law. Finally, we explained the primary cause of non-linear seepage behaviors with negative β in fractured sandstone samples.


  • Open Access

    Propagation network of tailings dam failure risk and the identification of key hazards

    by Zhixin Zhen, Xu Wu, Bo Ma, Huijie Zhao, Ying Zhang

    The tailings dam system is complex, and the dam structure changes continuously over time, which can make it difficult to identify key hazards of failure and characterize the accident formation process. To solve the above problems, based on complex network theory, the paper uses the identified hazards and the relationship between hazards to construct the propagation network of tailings dam failure risk (PNTDFR). The traditional analysis methods of network centrality usually focus on one aspect of the information of the network, while it cannot take into account to absorb the advantages of different methods, resulting in the difference between identified key nodes and real key hazards. To find the key hazards of tailing dam failure, based on the characteristics of multi-stage propagation of failure risk, the paper proposes a multi-stage collaborative hazard remediation method (MCHRM) to determine the importance of hazard nodes by absorbing the advantages of different centrality methods under different hazard remediation (deletion) ratios. The paper applies the above methods to Feijão Dam I. It can be found that when the priority remediation range is increased to 45%, the key hazards obtained by the MCHRM will cover all the causes of accidents proposed by the Dam I failure investigation expert group. Besides, the paper compares the monitoring data, daily inspection results and safety evaluation information of key hazards with the ‘Grading standards of hazard indicators’, and obtains the formation process of the Dam I failure and 30 key hazards in trigger state.


  • Open Access

    Research on the Mechanical Properties and Damage Constitutive Model of Multi-Shape Fractured Sandstone under Hydro-Mechanical Coupling

    by Ying Zhang, Xu Wu, Qifeng Guo, Zhaohong Zhang, Meifeng Cai, Limei Tian

    In this paper, mechanical property tests of sandstone with multiple shapes of prefabricated fractures (single, T-shaped, and Y-shaped fractures) are carried out through the MTS815 rock mechanics testing machine and the Teledyne ISCO D-Series Pumps system. Considering the hydro-mechanical coupling effects, the experiments reveal the key thresholds, strength characteristics and deformation laws of multi-shape fractured sandstones during the progressive failure process. According to the elastic-plastic theory, the continuous damage theory and the statistical damage theory, a new damage model is constructed, which fully reflects the coupled effects among water, micro flaws and macroscopic prefabricated fractures. The crack closure stress σcc, crack initiation stress σci and damage stress σcd of multi-shape fractured sandstone samples are determined by the proposed volumetric strain response method. In the range of 0–90°, the σcc and σci of the multi-shape fractured sandstone samples are different, as well as the angles when the σcd and peak strength (σc) reach their peak values. The stress ratios (the σcc/σc, σci/σc, and σcd/σc are collectively referred to as stress ratios) are hardly affected by the shape and inclination of the fractures inside the rock. According to strength analysis and deformation characteristics, the weakening effect of water has less of an influence on the strength than prefabricated fractures. The stress–strain curve obtained, based on the hydro-mechanical coupling test, is in good agreement with the theoretical curve generated by the damage constitutive model, verifying the rationality of the damage constitutive model. In addition, the fracture inclination only affects the numerical value of the total damage variable of multi-shape fractured sandstone samples, and has minor effects on its variation trend.


  • Open Access

    Nonlinear Seepage Behaviors of Pore-Fracture Sandstone under Hydro-Mechanical Coupling

    by Ying Zhang, Xu Wu, Qifeng Guo, Zhaohong Zhang, Meifeng Cai

    This work focused on the nonlinear seepage behaviors of flow in pore-fracture media. Natural sandstones were selected to prefabricate single-fracture specimens with different inclinations (0–90°). Seepage tests of combined media were performed under different confining pressures (8–10 MPa) and different water pressures (3–7 MPa) in a triaxial pressure chamber. The fitting analysis of experimental data showed that Forchheimer’s law described the nonlinear characteristics of flow in the pore-fracture media. Linear term coefficient a and nonlinear term coefficient b of the sandstone samples with different inclinations changed more obviously with the increased inclination. When the fracture inclination was greater than 30°, a and b values had a sudden jump. The nonlinear inertial-parameter equation of fluid flow in pore-fracture media was proposed based on non-Darcy flow coefficient β and inherent permeability k. The applicability of the following methods to evaluate Darcy’s law was discussed, including normalized hydraulic conductivity, pressure gradient ratio, and discharge ratio. The three methods were able to determine critical parameters and distinguish linear and nonlinear flow. Furthermore, it was specified for the first time that when β was negative, critical nonlinear effect E was −0.1, and Forchheimer’s coefficient F0 was −0.091. In the −∇P-Q relationship, the fitting curve was convex to the −∇P axis, and the increase of Q was higher than the linear increase, presenting the nonlinearity of overflow. On the one hand, the fractures and pores were compressed under the confining pressure due to the prefabricated fractures of different shapes and different inclinations. A higher seepage water pressure was needed to stabilize the seepage system with the excessive flow rate. On the other hand, the barrier effect of the fluid inside the rock was completely lost because the fluid expanded the seepage channel. Its permeability was changed, leading to seepage instability.


  • Open Access

    Propagation Laws of Reclamation Risk in Tailings Ponds Using Complex Network Theory

    by Zhixin Zhen, Ying Zhang, Mengrong Hu

    Accidents have occurred periodically in the tailings ponds where mine solid waste is stored in recent years, and thus their safety has become one of the constraints restricting the sustainable development of the mining industry. Reclamation is an important way to treat tailings ponds, but improper reclamation methods and measures not only cannot reduce the accident risk of tailings ponds, but will further increase the pollution to the surrounding environment. The influencing factors of reclamation accidents in tailings ponds are complex, and the existing models cannot characterize them. In order to study the propagation process of tailings pond reclamation risk, this paper proposes a three-dimensional identification framework for accident hazards based on evidence (TDIFAHE) to identify all potential hazards that may occur during the reclamation stage, and obtain a list of hazards. Based on the complex network theory, this paper uses identified hazards as network nodes and the correlation between hazards as the edges of the network. Based on the identified hazard data, the evolution network of reclamation risk in tailings ponds (ENRRTP) is constructed. By analyzing the statistical characteristics of ENRRTP, it can be found that ENRRTP has small world and scale-free characteristics. The above characteristics show that the reclamation risk of tailings ponds is coupled with multiple factors and the disaster path is short. Giving priority to those hub hazards that have a dominant impact on the reclamation risk can significantly reduce the reclamation risk of the tailings pond.