CTCisil Timuralp

Cisil Timuralp

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Cisil Timuralp has a total of 23 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Experimental assessment of energy consumption and CO 2 impacts of compressed air leakage across industrial sectors

    by Arda Zaim, Cisil Timuralp, Haydar Aras

    This study evaluates energy consumption resulting from compressed air leakage and the associated CO 2 equivalent emissions in industrial pneumatic systems. The analysis is based on ultrasonic field measurements conducted in 10 industrial facilities in Turkey. Measurements were performed under normal production conditions. Detected leakage points were classified by equipment category and measured flow rate range. Annual energy losses were calculated using a common SEC reference. The corresponding emission values were calculated using the national electricity emission factor. Leakage ratios ranged from 7% to 33% across the investigated facilities. Facilities with similar system scale showed different leakage ratios. Annual leakage-related energy losses ranged from 26.3 to 271.8 MWh per year. Normalized hourly losses ranged from 4 to 38 kWh/h. The calculated emission values ranged from 10 to 120 tCO 2 per year. Fittings and tubing showed the highest leakage contribution among equipment categories in the measured dataset. Connection sealing was the second major source group. Flow rate range classification separated leakage presence from leakage impact within equipment categories. The findings connect leakage location and measured flow rate with energy loss and calculated emission values in industrial compressed air systems.

  • Open Access

    Numerical and Experimental Analysis of Cooling System Performance in Induction Hobs: A Comparison of Heatsink Designs

    by Ayberk Salim Mayil, Cisil Timuralp

    The increasing demand for induction hobs necessitates efficient cooling systems to ensure the safe operation of electronic cut-outs. This study investigates the thermal representation of three different ignition designs integrated into an induction hob cooling system. A simplified model consisting of a radial fan, a daughterboard, and the electronics installed in the systems is used for the maintenance of the system. Remote measurements of air velocities at the cooler outlets are compared with the results obtained through programmable system dynamics (CFD) operations using FloEFD v2021.1 software. The findings of the study using the k-ε turbulence model show that Type 1 temperature is resistant to the lowest surface temperature for both the closest (IGBT 1) and the farthest (IGBT 2) temperature to the fan. Conversely, Type 3 temperatures exhibited high temperatures. Air velocity comparisons showed a maximum error rate of 30%, which is acceptable considering the variability in Type 1. Measurement system evaluation and DOE study were continued to increase the experimental range. This study demonstrates the utility offered by heatsink design in optimizing the cooling system of induction hobs and provides valuable insights for integrating thermal management systems.

  • Open Access

    Evaluation of Optimum Insulation Thickness According to External Wall Types to Be Used in Buildings to Be Reconstructed in Turkey

    by Cisil Timuralp, Nil Aras, Nuri Sisman, Haydar Aras

    The external walls of a building represent the interface between the interior and exterior environments. Insulating external walls represents the most cost-effective means of ensuring indoor comfort. Despite the prevailing assumption that insulation will increase the cost of the building, this study has demonstrated that this is not the case. Notwithstanding the increase in investment costs, the application of insulation to the external walls has been demonstrated to result in a reduction in fuel consumption and operating costs. In accordance with TS 825, there are five distinct degree-day zones, with the requisite heat loads in these zones exhibiting variability. Accordingly, a cost-based methodology is required to ascertain the optimal insulation thicknesses for the various degree-day zones. In this study, the gains to be obtained in the case of using three different insulation materials for five different wall types to be used in the buildings to be built instead of the buildings destroyed in the earthquake in Turkey in 2023 were analyzed. Samples from three degree-day zones affected by earthquakes were assessed for insulation, wall structures, and fuel types. The study assesses optimum insulation thickness, investment cost, annual fuel savings, annual economic benefits, and investment payback period.


  • PANEL RADYATÖR VE ÜRETİM PROSESİNİN ARAŞTIRILMASI

    by Umut Uçak, Çisil Timuralp, Turan Amcaoğlu

    Panel radyatörlerin üretim süreçlerinin detaylı incelenmesi, sektördeki teknolojik gelişmelerin anlaşılmasına katkı sağlamakta ve bu cihazların tasarım ve üretim aşamalarının iyileştirilmesine yönelik önemli bilgiler sunmaktadır. Bu derleme makale hem akademik hem de endüstriyel alanda bu alanda çalışanlara rehber niteliği taşımaktadır.

  • TÜRKİYE’DE 2013-2023 YILLARI ARASINDA MAKİNE SEKTÖRÜNDE YAŞANAN İŞ KAZALARININ MALİYET ANALİZİ

    by Mert Can Ilgın, Çisil Timuralp

    Her yıl büyük bir kısmı kolaylıkla önlenebilecek iş kazaları ve meslek hastalıkları sonucu pek çok insan hayatını kaybetmekte veya engelli hale gelmektedir. İş kazalarına karşı yeterli önlem almamanın sonuçlarını daha net bir şekilde ortaya koyabilmek için kaza maliyetlerinin hesaplanması son derece önemlidir. İş kazalarının maliyetleri literatürde direkt ve indirekt maliyetler olarak iki gruba ayrılmaktadır. Bu çalışmada, 2013-2023 yılları arasında makine sektöründe yaşanan iş kazalarındaki bu iki grup maliyet ortaya konularak, bu maliyetin yüklediği ekonomik yükün analiz edilmesi amaçlanmaktadır. Çalışmada direkt maliyetlerin hesaplanmasında 5510 sayılı Sosyal Sigortalar ve Genel Sağlık Sigortası Kanunundan, indirekt maliyetlerin hesaplanmasında ise İngiltere Sağlık ve Güvenlik Müdürlüğünün “Yıllık Kaza Maliyetlerinin Hesaplanması” yaklaşımından yararlanılarak Türkiye’de 2013-2023 yılları arasında makine sektöründe gerçekleşen iş kazalarının maliyetleri karşılaştırmalı olarak incelenmektedir. Çalışmada iş kazası maliyetlerinin, kaza sayılarının, asgari ücretin ve döviz kurlarının artışıyla birlikte her yıl düzenli olarak artış gösterdiği ve 2023 yılında 4.470.466.863,73 TL’ye ulaşarak hesaplamaların yapıldığı 11 yıllık dönemde en yüksek değere ulaştığı görülmüştür.


  • ÜRETİLEN RÜZGAR ENERJİSİ TAHMİNİNDE HAVA KOŞULU VERİLERİNİN İSTATİSTİKSEL ANALİZİ VE MODELLENMESİ

    by Ege Erginel, Çisil Timuralp

    Dünya çapında ve ülkemizde yaygın olarak kullanılan yenilenebilir enerji kaynaklarından rüzgâr enerjisi Türkiye’nin enerji ihtiyacının %10,6’sını karşılamaktadır. Rüzgâr türbini, rüzgârdaki kinetik enerjiyi elektrik enerjisine dönüştüren sistemdir. Rüzgâr türbinin tasarımı ve doğal faktörler üretim kapasitesini doğrudan ve dolaylı olarak etkilemektedir. Doğal faktörlerin içerisinde rüzgâr santralinin kurulduğu konum ve konumdaki hâkim hava olayları yer almaktadır. Rüzgârdan üretilen enerjinin hava sıcaklığı, nemlilik, anlık esinti ve rüzgâr hızı gibi değişkenler ile ilişkisinin olduğu düşünülmektedir. Bu çalışmada, bahsedilen hâkim hava olayları verilerinin üretilen enerji ile arasındaki ilişkinin istatistiksel analizi yapılmış ve yorumlanmıştır. Araştırma için Eskişehir bölgesinde kurulu, Kartal Res rüzgar enerji santrali seçilmiştir. İlgili rüzgar türbininden Ekim-2023 ayı için toplanan veriler ile hava koşulları verileri arasındaki ilişkiler pearson-korelasyon analizi ile belirlenmiş, üretilen enerjiye etki eden değişkenlerin belirlenmesi için ise regresyon analizi yapılmıştır. Üretilen enerjinin tahmininde rüzgar hızına bağlı olarak kübik matematiksel modelin daha iyi olduğu ortaya konmuştur. Bahsedilen kübik matematiksel modelin üretilen enerjideki değişkenliği R2(adj)=%65,39 ile iyi derecede açıkladığı tespit edilmiştir.

  • Open Access

    UÇAKLARDAN KAYNAKLANAN KARBON EMİSYONUNUN ESKİŞEHİR HASAN POLATKAN HAVALİMANI İÇİN BELİRLENMESİ

    by Çisil Timuralp, Furkan Rıza Mercan

    Bu çalışmada, havacılık sektöründe karbon ayak izinin belirlenmesi ve azaltılması ile ilgili örnek bir uygulama yapılmıştır. Uygulamada, Eskişehir ilinde faaliyette olan Hasan Polatkan Havalimanı’nın 2023 yılındaki uçuşları baz alınarak karbon ayak izi hesaplanması amacıyla bir süreç gerçekleştirilmiştir. Çalışmada, emisyon hesaplamalarında Hükümetler Arası İklim Değişikliği Paneli tarafından tavsiye edilen Tier yaklaşım metodu kullanılmıştır. Ulaştırmadan kaynaklanan 〖CO〗_2 emisyon miktarı 2023 yılı Hasan Polatkan Havalimanı’nında 6.893.160 kg olarak hesaplanmıştır. Sonuç olarak; havayolu ulaştırma sektöründe kullanılan uçakların üreticileri ile düzenleyici kurumlar arasında sürdürülebilirlik konusunda bir standardizasyonun acilen sağlanmasının gerekli oluğu tespit edilmiştir.


  • CFD Analysis of Liquid-Cooled Heatsink Using Nanofluids in Computer Processors

    by Gulnaz Topcu, Umran Ercetin, Cisil Timuralp

    In this study, a computer model of the Zalman ZM-WB3 Gold heat exchanger which is one of the liquid-cooled computer processors in the market has been generated and the model has been confirmed by the previous researchers models and experimental data. Then, the fin thickness and heights of the same heat exchanger and the type of liquid fluid in which the heat exchanger operates have been changed. The CFD analyzes of the new models were performed by using Ansys Fluent 17.1 program. Following that, nano heat removal (cooling) performances were investigated with models using rectangular fin fluid heat exchangers with different fin heights of 5 mm, 5.5 mm and 5.7 mm, and different fin thicknesses of 1.2 mm, 1.4 mm, 1.6 mm, 1.8 mm and 2 mm, and different fluids as water, copper oxide-water (CuO-H2O) nanofluids with volume ratios of 2.25% and 0.86%, and graphene oxide (GO-H2O) nanofluid with the volume ratio of 0.01%. It was concluded that the best CPU cooler performance could be achieved by using CuO - H2O as nanofluid with a volumetric ratio of 2.25% with a heat exchanger that has a 5.5 mm fin height and 2.0 mm fin thickness.


  • Art Arda Yerleştirilmiş Eş Sıcaklıktaki İki Silindir Etrafında Akış ve Isı Geçişi

    by Zerrin Sert, Çisil Ti̇muralp

    Bu çalışmada, ard ard yerleştirilen eş sıcaklıktaki iki silindir etrafındaki akış ve ısı geçişi geçici rejimde sayısal olarak incelenmiştir. İki boyutlu, geçici rejimde süreklilik, momentum ve enerji denklemleri Fluent yazılımı kullanılarak çözdürülmüştür. Çalışma akışkanı olarak hava (Pr=0.7) ve su (Pr=7) seçilmiştir. Reynolds sayısı 100, 150 ve 200 olarak alınmıştır. Ayrıca silindir merkezleri arasındaki uzaklık, L/D=1.5 ve 5 olarak seçilmiştir. Her durum için elde edilen sürükleme katsayısı, kaldırma katsayısı ve Nusselt sayısı gibi akış ve ısı transfer parametreleri, literatürdeki mevcut çalışmalarla karşılaştırılmıştır. L/D=1.5 olduğunda iki silindir arasında girdaplar oluşmazken, L/D=5 durumunda iki silindir arasında girdapların oluştuğu görülmektedir. Ayrıca Reynolds sayısının artması ile aşağı akış bölgesinde vorteksler ikinci silindire daha yakın bir mesafede oluşmuştur.

  • A comparative study of waste energy recovery from a hot-oil central boiler in a textile finishing factory

    by Hakan Kavak, Cisil Timuralp, Nimeti Doner

    Energy consumption in the textile industry is a significant part of the production cost. A shell-and-tube heat exchanger (STHX) was designed and manufactured for waste energy recovery from a hot-oil boiler in a textile finishing factory. An STHX with a single pass, including finned tubes and no baffle, was manufactured. By providing waste energy recovery to the applied system, air is released to the environment at 323 K instead of 525 K. Two scenarios were analyzed: (i) the designed STHX, alternatively with finned and unfinned-tube designs; and (ii) a double-pipe heat exchanger (DPHX) under the same operating conditions. These two cases were compared in terms of thermal performance. The applied system achieved an energy recovery of approximately 74.2%. The application of finned-tubes has an effect of between 11% and 24% on the total heat transfer coefficient. Applying the DPHX would provide thermal energy recovery of approximately 13% under the same operating conditions. The reason for the greater waste energy recovery when applying STHX is also shown by this analysis. Abbreviations: NTU: number of transfer units