WLWei Lian

Wei Lian

*This is an algorithmically generated author record based on publicly available information.

Wei Lian has a total of 25 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Mechanisms and Applications of Casing Running Mechanics in CCUS Extended‐Reach Horizontal Wells

    by Jingpeng Wang, Jun Li, Wei Lian, Zongyu Lu, Yanxian Wu, Tao Wan

    In this paper, the research on casing running is analyzed. By analyzing the stress and deformation of casing string with centralizer, the calculation model of friction, bending and centralizer pointing force in the process of horizontal down‐hole running of casing string is derived, and the friction between casing and running hole wall is solved by iterative method. The mathematical model is used to entangle the bending force of casing. When the string is bent along the bending direction of borehole trajectory, the bending force is related to the casing outer diameter, cross‐sectional area and string length. Then, the influence of casing additional force, such as drilling fluid viscous resistance, keyway rock breaking resistance, casing buckling additional load, casing running dynamic load and rotating casing running, on casing friction is analyzed in detail. The dynamic load of running casing makes the casing in curved and vertical sections bear large alternating load of tension and pressure, and rotating casing running may be an effective measure to reduce the friction of running casing. To run casing safely in extended reach horizontal well, the floating casing technology was simulated and analyzed. The safety of the horizontal well casing has been compromised, providing a casing cement sheath safety guarantee for future CO 2 injection production measures in oil and gas wells.


  • Open Access

    Study on the Construction of a Nonlinear Creep Constitutive Model of Salt-Gypsum Rock in the Bayan Deep and the Critical Value of Wellbore Shrinkage Liquid Column Pressure

    by Penglin Liu, Aobo Yin, Tairan Liang, Wen Sun, Wei Lian, Bo Zhang, Shanpo Jia, Jinchuan Huang

    Aiming at the problems of borehole shrinkage and pipe sticking caused by creep in salt-gypsum rock formations during deep well drilling, multi-field coupling creep experiments on deep salt-bearing gypsum mudstone were carried out. Furthermore, a nonlinear creep constitutive model was constructed based on the Drucker–Prager criterion, and the critical value of liquid column pressure for borehole shrinkage was determined through numerical simulation. Experiments show that at 140 °C, salt-gypsum rock is mainly subjected to brittle failure with single shear fracture, while at 180 °C, multiple sets of cross-cutting shear bands form, shifting to plastic flow-dominated composite failure. The coupling effect of confining pressure and deviatoric stress is temperature-dependent; the critical deviatoric stress is independent of confining pressure at 140 °C, but decreases significantly with increasing confining pressure at 180 °C, revealing that salt-gypsum rock is more prone to plastic flow under high temperatures and confining pressure. The creep constitutive equation was further determined, and fitting parameters show that the stress exponent m = 2–5 and the time exponent n decrease linearly with the increase in deviatoric stress, and the model can accurately describe the characteristics of three-stage creep. The numerical simulation found that there is a nonlinear relationship between the drilling fluid density and borehole shrinkage; the shrinkage rate exceeds 1.47% when the density is ≤2.0 g/cm3, and the expansion amount is >1.0 mm when ≥2.4 g/cm3. The critical safe density range is 2.1–2.3 g/cm3, which is consistent with the field data in the Bayan area. The research results provide an experimental basis and quantitative method for the dynamic regulation of drilling fluid density in deep gypsum rock formations, and have engineering guiding significance for preventing borehole wall instability.

  • Open Access

    Research on the Pore Evolution of Oil Shale under Different Thermal Treatment Temperatures Using NMR and FE-SEM Methods

    by Yan Xi, Jun Li, Wei Lian, Haifeng Fu, Yue Qi, Yudong Tian

    Underground in situ pyrolysis for oil shale extraction is currently significant; the evolutions in microstructure, porosity, and permeability parameters are essential factors in evaluating the productivity of oil shale after pyrolysis. With the underground oil shale reservoir core, obtained from Jimsar Sag in the Junggar Basin in China, as the research object, the samples were subjected to the treatment at different high temperatures (400°C, 500°C, 600°C, and 700°C). The NMR and FE-SEM experiments on oil shale samples were conducted; the relaxation spectra, pore size distribution, and porosity and permeability variation were analyzed; and the relationships between movable fluid saturation and porosity and permeability were established, respectively. The results showed that when the thermal treatment temperature increased, the porosity and permeability of oil shale rose continuously but showed different laws. With the temperature being lower than 400°C, the porosity increased slowly, and the growth rate of porosity increased rapidly when the thermal treatment temperature was higher than 500°C. In the pyrolysis temperature range of 25°C~400°C, the growth rate of permeability was relatively slow. With the continuously enhancing temperature (500°C~600°C), the growth rate of permeability accelerated rapidly. When the temperature continued to rise (700°C), the increase of permeability began to slow down. There is a nonlinear correlation between porosity and movable fluid saturation and an approximately linear correlation between permeability and movable fluid saturation. The findings showed that 600°C was the suitable temperature for the pyrolysis of oil shale.


  • Sealing Failure Mechanism and Control Method for Cement Sheath during Hydraulic Fracturing

    by Wei Lian, Jun Li, Qian Tao, Gonghui Liu, Wei Wang, Kai Ren

    This study focused on the sealing failure mechanism and control method for a cement sheath during hydraulic fracturing. Taking a shale gas well as an example, whole wellbore numerical models of the casing-cement sheath-formation assembly were established, failure modes of the cement sheath at different depths were clarified, and control methods were proposed based on the calculation results. The following conclusions were drawn. (1) The maximum radial/tangential stress of the cement sheath increased/decreased with an increase in the depth, and the cement sheath above the intermediate casing shoe posed the risk of tangential tensile failure, resulting in tensile cracks. The cement sheath below the intermediate casing shoe produced a micro-annulus under a cyclic casing pressure, and the tensile cracks and micro-annulus constituted passages for the sustained casing pressure. (2) The swelling stress of the expansion cement slurry could offset the circumferential tensile stress and increase the radial compressive stress. Because a cement sheath with a high Young’s modulus usually exhibits high tensile and compressive strengths, it is recommended to use a high Young’s modulus cement slurry system above the intermediate casing shoe and optimize the free expansion ratio. (3) In comparison with ordinary cement stone, low residual strain cement stone exhibited a larger elastic deformation interval. The cumulative residual strain caused by cyclic loading was smaller, and the Young’s modulus demonstrated a lesser decrease. The results of an equivalent physical experiment demonstrated that an ordinary cement sheath lost its integrity after 13 loading cycles with a maximum casing pressure of 60 MPa. A low residual strain cement sheath could guarantee integrity after 30 loading cycles when the maximum casing pressure was 90 MPa, and sealing failure occurred after 11 loading cycles when the maximum casing pressure was 130 MPa. It is recommended to use a low residual strain cement slurry below the intermediate casing shoe to prevent a micro-annulus.


  • Open Access

    Formation mechanism of continuous gas leakage paths in cement sheath during hydraulic fracturing

    by Wei Lian, Jun Li, Qian Tao, Jinlong Du, Lei Wang, Yan Xi

    Continuous gas leakage paths of cement sheath during hydraulic fracturing were investigated in this study. The finite‐element models of a casing–cement‐sheath–formation assembly for the whole wellbore were established, the integrity of the cement sheath of the whole wellbore during single‐stage fracturing was analyzed firstly, and the factors affecting the integrity were examined. Furthermore, a cyclic compression test was conducted. Then, test results for the accumulative plastic strain of the cement sheath under the intermediate casing shoe during multistage fracturing were analyzed. Finally, the mechanism of dilatancy of cement stone in cyclic compression tests was analyzed. The results show that the radial and tangential stresses of the cement sheath increase and decrease, respectively, with depth. The cement sheath above the intermediate casing shoe had a risk of tensile failure, which could result in tangential tensile cracks. The cement sheath below the intermediate casing shoes had cumulative plastic strain, resulting in a microannulus. Reducing Young's modulus, increasing the Poisson ratio of the cement sheath, and reducing the pump pressure were beneficial to relieve the stress state. When the cyclic compressive stress exceeded the dilatation yield stress, the permeability increased with cycle numbers, and the increase in permeability provided another leakage path for gas migration.