Xinglong Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Xinglong Sun has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Bin Cao
College of Materials Science and Engineering Xi'an University of Science and Technology Xi'an China
1 shared publication - Haoran Sun
School of Materials Science and Engineering, Shenyang Ligong University, Shenyang 110159, China
1 shared publication - Hua Song
College of Chemistry & Chemical Engineering, Northeast Petroleum University, Daqing 163318, P.R. China
1 shared publication - Hualin Song
School of Architecture and Transportation Engineering, Guilin University of Electronic Technology, Guilin 541004, China
1 shared publication Huili Han
School of Materials Science and Engineering, Shenyang Ligong University, Shenyang 110159, China
1 shared publication- Longsheng Bao
School of Transportation and Geomatics Engineering, Shenyang Jianzhu University, Shenyang, China
1 shared publication
Latest Publications
- Open Access
- 1 July 2023
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2541 (1) , 012013
Study on the effect and mechanism of NaOH on the modification of fluorapatite: A new method of preparing fluor-hydroxyapatite
Fluorapatite (FA) and fluor-hydroxyapatite (FHA) have good biocompatibility to substitute for human hard tissue, whereas FA has more cytotoxic and genotoxic effects than FHA. In this study, a new method named nitric acid dissolution-recrystallization was proposed to achieve the modification of FA, and NaOH was used to introduce OH- into FA to prepare FHA in the recrystallization process. The effect and mechanism of NaOH/pH value on the modification of FA were investigated using XRD analysis, SEM detection, EDTA complexometric titration, and FT-IR measurements. XRD and SEM analyses indicated that the synthesized FHA at the pH value of 8.00 had the highest crystallinity and the largest crystal size, reaching 38.10 nm, and the crystal was in the form of short rods with a length of about 1 μm. It was found that the content of the F element in the synthesized FHA decreased as the pH value of the reaction system increased. When the pH value reached 8.00, the content of F was 0.60%, and the values of x and (2-x) in FHA [Ca10(PO4)6Fx(OH)2-x] were 0.16 and 1.84, respectively. FT-IR analysis further confirmed that the content of OH- in FHA obtained at the pH value of 8.00 was noticeably higher than that obtained at the pH value of 4.46. This work could provide a new prospect for utilizing FA to prepare FHA and be of great significance.
- 1 July 2023
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2541 (1) , 012013
Open AccessStudy on the effect and mechanism of NaOH on the modification of fluorapatite: A new method of preparing fluor-hydroxyapatite
Fluorapatite (FA) and fluor-hydroxyapatite (FHA) have good biocompatibility to substitute for human hard tissue, whereas FA has more cytotoxic and genotoxic effects than FHA. In this study, a new method named nitric acid dissolution-recrystallization was proposed to achieve the modification of FA, and NaOH was used to introduce OH- into FA to prepare FHA in the recrystallization process. The effect and mechanism of NaOH/pH value on the modification of FA were investigated using XRD analysis, SEM detection, EDTA complexometric titration, and FT-IR measurements. XRD and SEM analyses indicated that the synthesized FHA at the pH value of 8.00 had the highest crystallinity and the largest crystal size, reaching 38.10 nm, and the crystal was in the form of short rods with a length of about 1 μm. It was found that the content of the F element in the synthesized FHA decreased as the pH value of the reaction system increased. When the pH value reached 8.00, the content of F was 0.60%, and the values of x and (2-x) in FHA [Ca10(PO4)6Fx(OH)2-x] were 0.16 and 1.84, respectively. FT-IR analysis further confirmed that the content of OH- in FHA obtained at the pH value of 8.00 was noticeably higher than that obtained at the pH value of 4.46. This work could provide a new prospect for utilizing FA to prepare FHA and be of great significance.
- Open Access
- 1 January 2020
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2020 (1)
PC Cable‐Stayed Bridge Main Girder Shear Lag Effects: Assessment of Single Cable Plane in Construction Stage
A model test and finite element analysis were conducted in this study to determine the distribution law of shear lag effect in the main beam section, a box girder, during the cable‐stayed bridge construction process. The experimental and theoretical results were compared in an example of loading the control section. The stress value of the cable tension area of the main beam upper edge was found to markedly change when tensiling the cable force and was accompanied by prominent shear lag effect. After a hanging basket load was applied, the main beam of certain sections showed alternating positive and negative shear lag characteristics. The shear lag distribution law in the box girder of the single‐cable‐plane prestressed concrete cable‐stayed bridge along the longitudinal direction was determined in order to observe the stress distribution of the girder. The results show that finite element analysis of the plane bar system should be conducted at different positions in the bridge under construction; the calculated shear lag coefficient of the cable force acting at the cable end of the cantilever reflects the actual force. In the beam segments between the cable forces, the shear lag coefficient determined by the ratio of the bending moment to the axial force reflects the actual stress at the cable force action point. In the midspan beam section between the action points of cable forces, the shear lag coefficient of the bending moment reflects the actual stress. The section shear lag coefficient can be obtained by linear interpolation of the beam section between the cable action point and the middle of the span.
- 1 January 2020
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2020 (1)
Open AccessPC Cable‐Stayed Bridge Main Girder Shear Lag Effects: Assessment of Single Cable Plane in Construction Stage
A model test and finite element analysis were conducted in this study to determine the distribution law of shear lag effect in the main beam section, a box girder, during the cable‐stayed bridge construction process. The experimental and theoretical results were compared in an example of loading the control section. The stress value of the cable tension area of the main beam upper edge was found to markedly change when tensiling the cable force and was accompanied by prominent shear lag effect. After a hanging basket load was applied, the main beam of certain sections showed alternating positive and negative shear lag characteristics. The shear lag distribution law in the box girder of the single‐cable‐plane prestressed concrete cable‐stayed bridge along the longitudinal direction was determined in order to observe the stress distribution of the girder. The results show that finite element analysis of the plane bar system should be conducted at different positions in the bridge under construction; the calculated shear lag coefficient of the cable force acting at the cable end of the cantilever reflects the actual force. In the beam segments between the cable forces, the shear lag coefficient determined by the ratio of the bending moment to the axial force reflects the actual stress at the cable force action point. In the midspan beam section between the action points of cable forces, the shear lag coefficient of the bending moment reflects the actual stress. The section shear lag coefficient can be obtained by linear interpolation of the beam section between the cable action point and the middle of the span.
- 1 June 2016
- Published by SAGE Publications in Progress in Reaction Kinetics and Mechanism
- Vol. 41 (2) , 126-134
Kinetic studies on the tert-butylation of toluene over H-BEA zeolite
The highly selective synthesis of 4- tert-butyltoluene from toluene with tert-butyl alcohol over zeolite catalysts was performed in the liquid phase. The order of activity for alkylation over zeolite catalysts was as follows: H-BEA > H-Y > H-MOR > H-ZSM-5. The main reaction products observed were 4- tert-butyltoluene and 3- tert-butyltoluene. 2- tert-Butyltoluene was completely absent in the product. A kinetic study of the reaction of toluene with tert-butyl alcohol over pure H-BEA (Si/Al = 25) was performed. Experimental runs were conducted at 160, 170, 180 and 190 °C and reaction times of up to 240 min. Based on the results obtained, a simplified kinetic model was developed. The kinetics could be described by the pseudo first-order model.
- 1 June 2016
- Published by SAGE Publications in Progress in Reaction Kinetics and Mechanism
- Vol. 41 (2) , 126-134
Kinetic studies on the tert-butylation of toluene over H-BEA zeolite
The highly selective synthesis of 4- tert-butyltoluene from toluene with tert-butyl alcohol over zeolite catalysts was performed in the liquid phase. The order of activity for alkylation over zeolite catalysts was as follows: H-BEA > H-Y > H-MOR > H-ZSM-5. The main reaction products observed were 4- tert-butyltoluene and 3- tert-butyltoluene. 2- tert-Butyltoluene was completely absent in the product. A kinetic study of the reaction of toluene with tert-butyl alcohol over pure H-BEA (Si/Al = 25) was performed. Experimental runs were conducted at 160, 170, 180 and 190 °C and reaction times of up to 240 min. Based on the results obtained, a simplified kinetic model was developed. The kinetics could be described by the pseudo first-order model.