Laurie Da Silva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Laurie Da Silva has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Amborish Banerjee
Advanced Forming Research Centre (AFRC), University of Strathclyde, Inchinnan, Renfrewshire, UK
3 shared publications - Athanasios Toumpis
Department of Mechanical & Aerospace Engineering, University of Strathclyde, James Weir Building, 75 Montrose Street, Glasgow G1 1XJ, UK
2 shared publications - Michail Dellepiane
Department of Mechanical & Aerospace Engineering, University of Strathclyde, Glasgow G1 1XJ, UK
2 shared publications - Salaheddin Rahimi
Advanced Forming Research Centre, University of Strathclyde, 85 Inchinnan Drive, Glasgow PA4 9LJ, UK
2 shared publications - Andrew Platts
University of Strathclyde Advanced Forming Research Centre (AFRC) 85 Inchinnan Drive, Inchinnan, Renfrewshire, PA4 9LJ , UK
1 shared publication - Andrew Wylie
University of Strathclyde Advanced Forming Research Centre (AFRC) 85 Inchinnan Drive, Inchinnan, Renfrewshire, PA 4 9LJ , UK
1 shared publication
Latest Publications
- Open Access
Metallurgical and Mechanical Property Investigation of ETP Cu Similar Hybrid Friction Welds for Nuclear Fusion Applications
The evolution of microstructure and mechanical properties in electrolytic tough-pitch (ETP) copper subjected to hybrid friction welding (HFW) was investigated. The effect of introducing a programmable brake on the flywheel’s rotation while maintaining constant friction and forging pressures was explored. The welded joints were examined through a series of investigations, including optical and scanning electron microscopy with electron backscatter diffraction, tensile and microhardness testing, followed by fractography. The optimised weld achieved the highest ultimate tensile strength (≈274 MPa), a 7.87% increase over the base material, and the greatest elongation (~22%), with ductile fractures and visible necking. The measured hardness distribution depicted higher values for the weld zone compared to the thermo-mechanically affected zone, both expressing a significant decrease from the heat-affected zone and base material due to pre-welding strain hardening existing within the copper alloy. EBSD analysis on the weld zone and thermo-mechanically affected zones revealed the presence of refined grains, with low grain orientation spread (GOS) and kernel average misorientation (KAM) values, which indicated the occurrence of dynamic recrystallisation (DRX) mechanisms during HFW. HFW was able to successfully produce ETP Cu-similar welds with 98.1% joint efficiency.
Open AccessMetallurgical and Mechanical Property Investigation of ETP Cu Similar Hybrid Friction Welds for Nuclear Fusion Applications
The evolution of microstructure and mechanical properties in electrolytic tough-pitch (ETP) copper subjected to hybrid friction welding (HFW) was investigated. The effect of introducing a programmable brake on the flywheel’s rotation while maintaining constant friction and forging pressures was explored. The welded joints were examined through a series of investigations, including optical and scanning electron microscopy with electron backscatter diffraction, tensile and microhardness testing, followed by fractography. The optimised weld achieved the highest ultimate tensile strength (≈274 MPa), a 7.87% increase over the base material, and the greatest elongation (~22%), with ductile fractures and visible necking. The measured hardness distribution depicted higher values for the weld zone compared to the thermo-mechanically affected zone, both expressing a significant decrease from the heat-affected zone and base material due to pre-welding strain hardening existing within the copper alloy. EBSD analysis on the weld zone and thermo-mechanically affected zones revealed the presence of refined grains, with low grain orientation spread (GOS) and kernel average misorientation (KAM) values, which indicated the occurrence of dynamic recrystallisation (DRX) mechanisms during HFW. HFW was able to successfully produce ETP Cu-similar welds with 98.1% joint efficiency.
- Open Access
- 18 January 2025
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 9 (1) , 27
Design and Development of a Bespoke Rotary Friction Welding Machine in Exploration of Joining Dissimilar Materials for Nuclear Applications
Rotary friction welding is a solid-state welding process that can manufacture high-integrity joints between similar and dissimilar materials with short weld times. However, access to expensive and complex industrial-grade friction welding machines is not always possible. This study explores the design process and functionality of a laboratory-scale friction welding setup following the fundamentals of large-scale machinery. The proposed setup is designed to be easily manufactured, employing the use of a calibrated drill press and load cell, thus ensuring welding parameters such as rotational speed and applied axial load are monitored. The decision to investigate rotary friction welding of aluminium bronze Ca104 to austenitic stainless steel AISI316 was taken to explore the limitations of this bespoke friction welding machine for prospective applications in the nuclear energy sector. The workpieces were friction welded at four sets of rotational speeds with constant friction and forging pressures. The microstructural evolution and mechanical properties of the dissimilar material welds were investigated via optical and scanning electron microscopy with energy dispersive spectroscopy, 4-point bend testing and microhardness measurements. Results show a change in the hardness along the weld interface and evidence of metallic diffusion between the dissimilar materials, demonstrating the successful application of the small-scale experimental setup.
- 18 January 2025
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 9 (1) , 27
Open AccessDesign and Development of a Bespoke Rotary Friction Welding Machine in Exploration of Joining Dissimilar Materials for Nuclear Applications
Rotary friction welding is a solid-state welding process that can manufacture high-integrity joints between similar and dissimilar materials with short weld times. However, access to expensive and complex industrial-grade friction welding machines is not always possible. This study explores the design process and functionality of a laboratory-scale friction welding setup following the fundamentals of large-scale machinery. The proposed setup is designed to be easily manufactured, employing the use of a calibrated drill press and load cell, thus ensuring welding parameters such as rotational speed and applied axial load are monitored. The decision to investigate rotary friction welding of aluminium bronze Ca104 to austenitic stainless steel AISI316 was taken to explore the limitations of this bespoke friction welding machine for prospective applications in the nuclear energy sector. The workpieces were friction welded at four sets of rotational speeds with constant friction and forging pressures. The microstructural evolution and mechanical properties of the dissimilar material welds were investigated via optical and scanning electron microscopy with energy dispersive spectroscopy, 4-point bend testing and microhardness measurements. Results show a change in the hardness along the weld interface and evidence of metallic diffusion between the dissimilar materials, demonstrating the successful application of the small-scale experimental setup.
- 16 August 2023
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 145 (10) , 1-38
Evolution of Microstructure in MLX®19 Maraging Steel During Rotary Friction Welding and Finite Element Modeling of the Process
Inertia friction welding (IFW) is a solid-state welding process utilised for joining engineering materials. In this paper, a 2.5D finite element (FE) model was developed to simulate IFW of MLX®19 maraging steel. The predicted results showed a non-uniform temperature distribution, with a decrease in temperature from the periphery to the centre of weld interface. Higher temperature and lower stress distributions were predicted in the weld zone (WZ) and the adjacent regions in the vicinity of the WZ. The von-Mises effective stress, effective strain and strain-rate were investigated at different time steps of the FE simulation. The effective stress was minimum at the weld interface, and the effective strain and strain-rate attained a quasi-steady state status with the on-going IFW after a threshold time (~6.5 s). The simulated results were validated by comparing the predicted flash morphology with an actual IFW weld, and temperature profiles measured at specific locations using embedded thermo-couples. The difference between the experimental and the simulated results was ~4.7%, implying a good convergence of the model. Microstructural characterisations were performed across different regions and the observed features were found to be in agreement with the expected microstructure based on the simulated thermal profiles, which included almost complete (~90%) and partial transformation of martensite to austenite in the WZ and thermo-mechanically affected zone (TMAZ), respectively. Analyses of crystallographic texture, showed that the material (i.e., both transformed austenite and martensite) underwent pure shear deformation during IFW.
- 16 August 2023
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 145 (10) , 1-38
Evolution of Microstructure in MLX®19 Maraging Steel During Rotary Friction Welding and Finite Element Modeling of the Process
Inertia friction welding (IFW) is a solid-state welding process utilised for joining engineering materials. In this paper, a 2.5D finite element (FE) model was developed to simulate IFW of MLX®19 maraging steel. The predicted results showed a non-uniform temperature distribution, with a decrease in temperature from the periphery to the centre of weld interface. Higher temperature and lower stress distributions were predicted in the weld zone (WZ) and the adjacent regions in the vicinity of the WZ. The von-Mises effective stress, effective strain and strain-rate were investigated at different time steps of the FE simulation. The effective stress was minimum at the weld interface, and the effective strain and strain-rate attained a quasi-steady state status with the on-going IFW after a threshold time (~6.5 s). The simulated results were validated by comparing the predicted flash morphology with an actual IFW weld, and temperature profiles measured at specific locations using embedded thermo-couples. The difference between the experimental and the simulated results was ~4.7%, implying a good convergence of the model. Microstructural characterisations were performed across different regions and the observed features were found to be in agreement with the expected microstructure based on the simulated thermal profiles, which included almost complete (~90%) and partial transformation of martensite to austenite in the WZ and thermo-mechanically affected zone (TMAZ), respectively. Analyses of crystallographic texture, showed that the material (i.e., both transformed austenite and martensite) underwent pure shear deformation during IFW.
- 27 September 2022
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 145 (2)
Near-Net Shape Manufacture of Ultra-High Strength Maraging Steel Using Flow Forming and Inertia Friction Welding: Experimental and Microstructural Characterization
Flow forming and inertia friction welding (IFW) have been widely used as manufacturing processes that produce high-value engineering components. Combining these two advanced processes facilitates the fabrication of near-net shape components leading to optimized designs. This study introduces the joining of flow-formed seamless tubes of MLX®19 maraging steel using the IFW process to fabricate a near-net shape component used in landing gears and missile parts. The as-received material was initially provided ≈30% reduction in thickness from the flow forming trials and then welded at four varying weld energies while maintaining constant friction and forge pressures. The mechanical behavior of the weldments was characterized, and the optimized weld parameters were determined. The concomitant microstructural evolution of the optimized weld was also examined to comprehend the underlying deformation mechanisms. The weld strength, axial shortening, and width of dynamic recrystallization (DRX) displayed an increasing trend with an increase in the weld energy. The weld-zone (WZ) and thermomechanical affected zone (TMAZ) showed the presence of martensite, whereas in the HAZ presence of intermetallic precipitates and reverted austenite was confirmed along with tempered martensite. Based on microstructural evidence, it was concluded that the peak temperature attained in the WZ was above Ac3, whereas in the TMAZ it was in-between Ac1 and Ac3. The evolution of crystallographic texture implied that WZ was subjected to pure shear deformation during the welding whereas the TMAZ experienced a combined shear and compressive deformation.
- 27 September 2022
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 145 (2)
Near-Net Shape Manufacture of Ultra-High Strength Maraging Steel Using Flow Forming and Inertia Friction Welding: Experimental and Microstructural Characterization
Flow forming and inertia friction welding (IFW) have been widely used as manufacturing processes that produce high-value engineering components. Combining these two advanced processes facilitates the fabrication of near-net shape components leading to optimized designs. This study introduces the joining of flow-formed seamless tubes of MLX®19 maraging steel using the IFW process to fabricate a near-net shape component used in landing gears and missile parts. The as-received material was initially provided ≈30% reduction in thickness from the flow forming trials and then welded at four varying weld energies while maintaining constant friction and forge pressures. The mechanical behavior of the weldments was characterized, and the optimized weld parameters were determined. The concomitant microstructural evolution of the optimized weld was also examined to comprehend the underlying deformation mechanisms. The weld strength, axial shortening, and width of dynamic recrystallization (DRX) displayed an increasing trend with an increase in the weld energy. The weld-zone (WZ) and thermomechanical affected zone (TMAZ) showed the presence of martensite, whereas in the HAZ presence of intermetallic precipitates and reverted austenite was confirmed along with tempered martensite. Based on microstructural evidence, it was concluded that the peak temperature attained in the WZ was above Ac3, whereas in the TMAZ it was in-between Ac1 and Ac3. The evolution of crystallographic texture implied that WZ was subjected to pure shear deformation during the welding whereas the TMAZ experienced a combined shear and compressive deformation.
- 6 December 2021
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 144 (7) , 1-30
Continuous Drive Friction Welding of AISI 8630 Low-Alloy Steel: Experimental Investigations on Microstructure Evolution and Mechanical Properties
Continuous drive friction welding (CDW) is a state-of-the-art solid-state welding technology for joining metallic components used in aerospace, oil and gas, and power generation industries. This study summarizes the results of mechanical and microstructural investigations on a modified AISI-8630 steel subjected to CDW. The effects of welding process parameters, including rotational speed, friction, and forge forces, during CDW were explored to determine an optimum welding condition. The mechanical properties of the weld, and microstructural characteristics across different regions of the weld were measured and examined. The microstructure characterization results suggest that the weld zone (WZ) experiences temperatures above the Ac3 and the thermo-mechanically affected zone (TMAZ) experiences temperatures between Ac1 and Ac3 of the material. Investigations with electron backscatter diffraction (EBSD) demonstrated the occurrence of strain-induced dynamic recrystallization in the weld. The weld demonstrated higher yield and ultimate tensile strengths at the expense of ductility and hardening capacity compared to the base metal (BM). The strain-hardening profiles of the welds exhibited a dual-slope characteristic, an indication of different levels of plastic deformation experienced by the constituent phases (i.e., martensite, bainite and ferrite) present in the microstructure. The maximum strength-to-ductility combination and static toughness values were obtained for the weld produced under the highest rotational speed, maximum friction force and an intermediate forge force of 1200–1400 rpm, 375–425 kN, and 600–650 kN, respectively.
- 6 December 2021
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 144 (7) , 1-30
Continuous Drive Friction Welding of AISI 8630 Low-Alloy Steel: Experimental Investigations on Microstructure Evolution and Mechanical Properties
Continuous drive friction welding (CDW) is a state-of-the-art solid-state welding technology for joining metallic components used in aerospace, oil and gas, and power generation industries. This study summarizes the results of mechanical and microstructural investigations on a modified AISI-8630 steel subjected to CDW. The effects of welding process parameters, including rotational speed, friction, and forge forces, during CDW were explored to determine an optimum welding condition. The mechanical properties of the weld, and microstructural characteristics across different regions of the weld were measured and examined. The microstructure characterization results suggest that the weld zone (WZ) experiences temperatures above the Ac3 and the thermo-mechanically affected zone (TMAZ) experiences temperatures between Ac1 and Ac3 of the material. Investigations with electron backscatter diffraction (EBSD) demonstrated the occurrence of strain-induced dynamic recrystallization in the weld. The weld demonstrated higher yield and ultimate tensile strengths at the expense of ductility and hardening capacity compared to the base metal (BM). The strain-hardening profiles of the welds exhibited a dual-slope characteristic, an indication of different levels of plastic deformation experienced by the constituent phases (i.e., martensite, bainite and ferrite) present in the microstructure. The maximum strength-to-ductility combination and static toughness values were obtained for the weld produced under the highest rotational speed, maximum friction force and an intermediate forge force of 1200–1400 rpm, 375–425 kN, and 600–650 kN, respectively.
- Open Access
- 29 March 2020
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 51 (6) , 3009-3029
Impact of a Multi-step Heat Treatment on Different Manufacturing Routes of 18CrNiMo7-6 Steel
Effect of an optimized multi-step heat treatment routine on conventional (machining from wrought bar stock) and alternate manufacturing routes (hot forging and cold rotary forging) for producing flat cylindrical-shaped machine drive components from 18CrNiMo7-6 steel was investigated. The microstructure and mechanical properties of the final component manufactured using these three different routes were analyzed using optical microscopy, electron backscatter diffraction (EBSD), hardness testing, electro-thermal mechanical testing (ETMT), and rotary bending fatigue testing (RBFT) before and after implementing the multi-step heat treatment. It was found that the multi-step heat treatment transformed the as-received microstructure into the tempered martensitic microstructure, improving hardness, tensile, and fatigue properties. The heat treatment produced desired properties for the components manufactured by all three different routes. However the cold rotary forging, which is the most material utilizing route over the others, benefited the most from the optimized heat treatment.
- 29 March 2020
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 51 (6) , 3009-3029
Open AccessImpact of a Multi-step Heat Treatment on Different Manufacturing Routes of 18CrNiMo7-6 Steel
Effect of an optimized multi-step heat treatment routine on conventional (machining from wrought bar stock) and alternate manufacturing routes (hot forging and cold rotary forging) for producing flat cylindrical-shaped machine drive components from 18CrNiMo7-6 steel was investigated. The microstructure and mechanical properties of the final component manufactured using these three different routes were analyzed using optical microscopy, electron backscatter diffraction (EBSD), hardness testing, electro-thermal mechanical testing (ETMT), and rotary bending fatigue testing (RBFT) before and after implementing the multi-step heat treatment. It was found that the multi-step heat treatment transformed the as-received microstructure into the tempered martensitic microstructure, improving hardness, tensile, and fatigue properties. The heat treatment produced desired properties for the components manufactured by all three different routes. However the cold rotary forging, which is the most material utilizing route over the others, benefited the most from the optimized heat treatment.