Hurmet Kucukgoncu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hurmet Kucukgoncu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Ahmet Özbayrak
Erciyes üniversitesi Mühendislik Fakültesi
8 shared publications - Huseyin Hilmi Aslanbay
Engineering Faculty, Civil Engineering Department, Erciyes University, Kayseri, Turkey.
5 shared publications - Yuksel Gul Aslanbay
Erciyes University
4 shared publications Fatih Altun
Erciyes University
3 shared publicationsYuksel Gul Aslanbay
3 shared publications- Fatih Altun
Erciyes University
2 shared publications
Latest Publications
- 23 May 2026
- Published by SAGE Publications in Advances in Structural Engineering
Failure mechanisms and damage evolution of geopolymer concrete beams under flexural loading: Experimental investigation and finite element analysis
This study investigates the failure behavior and damage mechanisms of geopolymer concrete (GPC) and ordinary Portland cement (OPC) reinforced concrete beams through a combined experimental and numerical approach. Flexural tests were conducted, and then displacement and crack development were monitored using high-precision total station measurements. Numerical analyses were performed using ABAQUS, and the consistency between experimental observations and numerical predictions was evaluated at yield and failure stages to characterize inelastic behavior and damage progression. The effects of key parameters, including tensile reinforcement ratio, geopolymer concrete formulations, and curing methods, on cracking behavior, stiffness degradation, and failure modes were investigated in detail. The results indicate that increasing the tensile reinforcement ratio enhances flexural stiffness and load-bearing capacity while reducing ductility at advanced damage stages. Compared to OPC beams, GPC beams exhibited narrower and more distributed crack patterns due to their distinct microstructural characteristics. Quantitatively, GPC beams exhibited approximately 15% greater deformation in the compression zone at failure, while tensile reinforcement strains were up to 23% higher at yield compared to OPC beams. In addition, the maximum crack width at failure in GPC beams was approximately 50% lower than that of OPC beams. These results indicate that, despite similar strength levels, GPC beams exhibit higher deformation capacity and more distributed damage behavior. The findings demonstrate that geopolymer concrete exhibits distinct failure characteristics compared to OPC and should be explicitly considered in structural design to improve damage control and failure prediction. Overall, the study highlights the potential of geopolymer concrete as a reliable and sustainable structural material.
- 23 May 2026
- Published by SAGE Publications in Advances in Structural Engineering
Failure mechanisms and damage evolution of geopolymer concrete beams under flexural loading: Experimental investigation and finite element analysis
This study investigates the failure behavior and damage mechanisms of geopolymer concrete (GPC) and ordinary Portland cement (OPC) reinforced concrete beams through a combined experimental and numerical approach. Flexural tests were conducted, and then displacement and crack development were monitored using high-precision total station measurements. Numerical analyses were performed using ABAQUS, and the consistency between experimental observations and numerical predictions was evaluated at yield and failure stages to characterize inelastic behavior and damage progression. The effects of key parameters, including tensile reinforcement ratio, geopolymer concrete formulations, and curing methods, on cracking behavior, stiffness degradation, and failure modes were investigated in detail. The results indicate that increasing the tensile reinforcement ratio enhances flexural stiffness and load-bearing capacity while reducing ductility at advanced damage stages. Compared to OPC beams, GPC beams exhibited narrower and more distributed crack patterns due to their distinct microstructural characteristics. Quantitatively, GPC beams exhibited approximately 15% greater deformation in the compression zone at failure, while tensile reinforcement strains were up to 23% higher at yield compared to OPC beams. In addition, the maximum crack width at failure in GPC beams was approximately 50% lower than that of OPC beams. These results indicate that, despite similar strength levels, GPC beams exhibit higher deformation capacity and more distributed damage behavior. The findings demonstrate that geopolymer concrete exhibits distinct failure characteristics compared to OPC and should be explicitly considered in structural design to improve damage control and failure prediction. Overall, the study highlights the potential of geopolymer concrete as a reliable and sustainable structural material.
- 7 November 2025
- Published by Elsevier in Composite Structures
- Vol. 376
Numerical analysis and experimental comparison of stress and stiffness parameters of steel reinforced geopolymer concrete columns
- 7 November 2025
- Published by Elsevier in Composite Structures
- Vol. 376
Numerical analysis and experimental comparison of stress and stiffness parameters of steel reinforced geopolymer concrete columns
- 11 August 2025
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 23 (13) , 5741-5772
Structural behavior of geopolymer reinforced concrete beams: experimental, numerical, and code-based assessment
- 11 August 2025
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 23 (13) , 5741-5772
Structural behavior of geopolymer reinforced concrete beams: experimental, numerical, and code-based assessment
- Open Access
- 25 June 2024
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 50 (11) , 8197-8223
Microstructural Analysis of Low-Calcium Fly Ash-Based Geopolymer Concrete with Different Ratios of Activator and Binder Under High Temperatures
Geopolymer concretes have emerged as an alternative to traditional Portland cement concretes with high strength, good durability, well corrosion performance and high-temperature resistance, and being a sustainable and environmentally friendly material. In this study, a comprehensive microstructural analysis of low-calcium fly ash-based geopolymer concrete samples with different alkali activator to binder ratios was conducted after exposure to temperatures ranging from 400 to 800 °C. The experimental results of the geopolymer concrete specimens found out significant findings, including a notable loss of mass and an approximate 80% decrease in compressive strength after exposure to 800 °C. The microstructural analysis underlined crack formation, voids and porosities in the geopolymer matrix at elevated temperatures, affecting the physical and mechanical properties of the material. The study presents significant insights into the behaviour of low-calcium fly ash-based geopolymer concrete with different binder and alkali activator ratios under high temperatures, revealing the performance of geopolymer concretes in extreme environments and the effect of incompatibility between geopolymer concrete and aggregate due to thermal temperature effects on this performance.
- 25 June 2024
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 50 (11) , 8197-8223
Open AccessMicrostructural Analysis of Low-Calcium Fly Ash-Based Geopolymer Concrete with Different Ratios of Activator and Binder Under High Temperatures
Geopolymer concretes have emerged as an alternative to traditional Portland cement concretes with high strength, good durability, well corrosion performance and high-temperature resistance, and being a sustainable and environmentally friendly material. In this study, a comprehensive microstructural analysis of low-calcium fly ash-based geopolymer concrete samples with different alkali activator to binder ratios was conducted after exposure to temperatures ranging from 400 to 800 °C. The experimental results of the geopolymer concrete specimens found out significant findings, including a notable loss of mass and an approximate 80% decrease in compressive strength after exposure to 800 °C. The microstructural analysis underlined crack formation, voids and porosities in the geopolymer matrix at elevated temperatures, affecting the physical and mechanical properties of the material. The study presents significant insights into the behaviour of low-calcium fly ash-based geopolymer concrete with different binder and alkali activator ratios under high temperatures, revealing the performance of geopolymer concretes in extreme environments and the effect of incompatibility between geopolymer concrete and aggregate due to thermal temperature effects on this performance.
- Open Access
- 17 March 2023
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
Sargısız betonun mekanik özelliklerinin TBDY 2018 ve diğer modellerle analitik ve deneysel karşılaştırılması
Betonarme elemanların davranışlarının anlaşılabilmesi için betonarmeyi oluşturan malzemelerin gerilme-şekil değiştirme davranışlarının bilinmesi gerekmektedir. Sargısız beton malzemesinin gerilme-şekil değiştirme davranışının tahmin edilebilmesi için pek çok matematiksel model geliştirilmiştir. Türkiye Bina Deprem Yönetmeliği 2018 (TBDY 2018) de de sargısız betonların gerilme-şekil değiştirme bağıntılarına yer verilmektedir. Ancak bu matematiksel modellerin dayanım, düktilite ve yük altında enerji tüketebilme kapasitesi açısından benzer özelliklerdeki deneysel numunelerden farkının tespit edilmesi oldukça önemlidir. Böylece sargısız beton modellerin, analitik yaklaşımlarının doğruluğu belirlenebilmektedir. Betonarme yapısal elemanların özellikle kesit davranışı araştırılırken ya da yük altında kesit tasarımları yapılırken söz konusu modellerin sergilediği davranışı bilmek büyük kolaylıklar sağlamaktadır. Bu nedenle, bu çalışmada TS 500 yönetmeliğinde yer alan beton sınıfları ve dayanımlarına uygun olarak üretilen numuneler basınç testine tabi tutulmuş, sonrasında ise bu dayanım sınıflarına ait sargısız beton davranışı için literatürde sık kullanılan matematiksel modeller ve TBDY 2018 de yer alan bağıntılar kullanılarak gerilme-şekil değiştirme grafikleri elde edilmiştir. Bu grafiklerden yararlanılarak düktilite ve enerji tüketebilme kapasitesi gibi mekanik özellikleri, TBDY 2018 ve diğer matematiksel modellerle, deneysel verilerden elde edilen değerler karşılaştırılarak farklılıkları ortaya konulmuştur. Buna göre göz önüne alınan beton modellerinin güçlü ve zayıf yönleri belirlenmiş ve kullanılan beton sınıfına ait dayanımın da modellerin performansı üzerinde etkili olduğu sonucuna varılmıştır.
- 17 March 2023
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
Open AccessSargısız betonun mekanik özelliklerinin TBDY 2018 ve diğer modellerle analitik ve deneysel karşılaştırılması
Betonarme elemanların davranışlarının anlaşılabilmesi için betonarmeyi oluşturan malzemelerin gerilme-şekil değiştirme davranışlarının bilinmesi gerekmektedir. Sargısız beton malzemesinin gerilme-şekil değiştirme davranışının tahmin edilebilmesi için pek çok matematiksel model geliştirilmiştir. Türkiye Bina Deprem Yönetmeliği 2018 (TBDY 2018) de de sargısız betonların gerilme-şekil değiştirme bağıntılarına yer verilmektedir. Ancak bu matematiksel modellerin dayanım, düktilite ve yük altında enerji tüketebilme kapasitesi açısından benzer özelliklerdeki deneysel numunelerden farkının tespit edilmesi oldukça önemlidir. Böylece sargısız beton modellerin, analitik yaklaşımlarının doğruluğu belirlenebilmektedir. Betonarme yapısal elemanların özellikle kesit davranışı araştırılırken ya da yük altında kesit tasarımları yapılırken söz konusu modellerin sergilediği davranışı bilmek büyük kolaylıklar sağlamaktadır. Bu nedenle, bu çalışmada TS 500 yönetmeliğinde yer alan beton sınıfları ve dayanımlarına uygun olarak üretilen numuneler basınç testine tabi tutulmuş, sonrasında ise bu dayanım sınıflarına ait sargısız beton davranışı için literatürde sık kullanılan matematiksel modeller ve TBDY 2018 de yer alan bağıntılar kullanılarak gerilme-şekil değiştirme grafikleri elde edilmiştir. Bu grafiklerden yararlanılarak düktilite ve enerji tüketebilme kapasitesi gibi mekanik özellikleri, TBDY 2018 ve diğer matematiksel modellerle, deneysel verilerden elde edilen değerler karşılaştırılarak farklılıkları ortaya konulmuştur. Buna göre göz önüne alınan beton modellerinin güçlü ve zayıf yönleri belirlenmiş ve kullanılan beton sınıfına ait dayanımın da modellerin performansı üzerinde etkili olduğu sonucuna varılmıştır.
- 27 January 2023
- Published by Elsevier in Structures
- Vol. 48, 2048-2061
Determination of stress-strain relationship based on alkali activator ratios in geopolymer concretes and development of empirical formulations
- 27 January 2023
- Published by Elsevier in Structures
- Vol. 48, 2048-2061
Determination of stress-strain relationship based on alkali activator ratios in geopolymer concretes and development of empirical formulations