Pushpapraj Singh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pushpapraj Singh has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Manu Garg
International College of Semiconductor Technology, National Yang Ming Chiao Tung University (NYCU), Hsinchu, Taiwan
13 shared publications - Nitish Kumar
CROMA, Univ. Grenoble Alpes, Univ. Savoie Mont Blanc, CNRS, Grenoble INP
12 shared publications - Dhairya Singh Arya
Centre for Applied Research in Electronics, IIT Delhi, New Delhi, India
10 shared publications - Sushil Kumar
Centre for Applied Research in Electronics (CARE), Indian Institute of Technology at Delhi (IITD), New Delhi, India
10 shared publications - Ankur Gupta
Centre for Applied Research in Electronics (CARE), Indian Institute of Technology Delhi, New Delhi, India
9 shared publications - Mujeeb Yousuf
Center of Applied Research in Electronics, Indian Institute of Technology Delhi, New Delhi, India
7 shared publications
Latest Publications
- 5 October 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (14)
Pressure-induced mode transition and physical model for a suspended hybrid tactile sensor
Flexible hybrid capacitive-piezoresistive tactile sensors face fundamental challenges in understanding regime transition physics. Here, we reveal and model a pressure-induced capacitive to piezoresistive transition in a suspended PEDOT:PSS/LIG/PDMS tactile element. By combining fringe-field partial capacitance analysis with conductance evolution tracking, we correlate micro-contact formation with the apparent capacitance drop at contact onset. We further identify a fringe-field proximity effect (capacitance dip as a conductive body enters the field) that precedes contact. The physics of the entire transition, from non-contact to fully resistive operation, is validated through combined conductance, phase, and I–V measurements. This compact device-level study establishes a physical model that clarifies transition behavior observed in the device. Furthermore, it provides initial design principles potentially useful for next-generation hybrid tactile sensors.
- 5 October 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (14)
Pressure-induced mode transition and physical model for a suspended hybrid tactile sensor
Flexible hybrid capacitive-piezoresistive tactile sensors face fundamental challenges in understanding regime transition physics. Here, we reveal and model a pressure-induced capacitive to piezoresistive transition in a suspended PEDOT:PSS/LIG/PDMS tactile element. By combining fringe-field partial capacitance analysis with conductance evolution tracking, we correlate micro-contact formation with the apparent capacitance drop at contact onset. We further identify a fringe-field proximity effect (capacitance dip as a conductive body enters the field) that precedes contact. The physics of the entire transition, from non-contact to fully resistive operation, is validated through combined conductance, phase, and I–V measurements. This compact device-level study establishes a physical model that clarifies transition behavior observed in the device. Furthermore, it provides initial design principles potentially useful for next-generation hybrid tactile sensors.
- 17 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (5) , 2817-2823
Dual-Isolation Hybrid Tactile Array With Fully Parallel Analog Front-End and Sub-0.3% Crosstalk
Effective mitigation of inter-pixel crosstalk remains a pivotal challenge for tactile sensor arrays in advanced human–machine interfaces (HMIs). We present a flexible tactile array that addresses this problem through a holistic dual-isolation strategy. This approach integrates mechanical isolation via SU-8 pixel cavities with electronic isolation via a fully parallel, per-channel analog-to-digital converter (ADC) analog front-end. It collectively suppresses inter-pixel crosstalk to ${\mathrm {kPa}}^{-{1}}$ , respectively. The device also demonstrates stable performance over 2400 cycles. A scalable hierarchical readout system (MSP430–ESP32) provides a synchronized wireless acquisition with an $8.07~\pm ~2$ ms sensor-to-ready latency and a power profile that outlines a clear scaling roadmap. This architecture establishes a robust foundation for high-performance, low-interference tactile arrays in real-time HMIs.
- 17 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (5) , 2817-2823
Dual-Isolation Hybrid Tactile Array With Fully Parallel Analog Front-End and Sub-0.3% Crosstalk
Effective mitigation of inter-pixel crosstalk remains a pivotal challenge for tactile sensor arrays in advanced human–machine interfaces (HMIs). We present a flexible tactile array that addresses this problem through a holistic dual-isolation strategy. This approach integrates mechanical isolation via SU-8 pixel cavities with electronic isolation via a fully parallel, per-channel analog-to-digital converter (ADC) analog front-end. It collectively suppresses inter-pixel crosstalk to ${\mathrm {kPa}}^{-{1}}$ , respectively. The device also demonstrates stable performance over 2400 cycles. A scalable hierarchical readout system (MSP430–ESP32) provides a synchronized wireless acquisition with an $8.07~\pm ~2$ ms sensor-to-ready latency and a power profile that outlines a clear scaling roadmap. This architecture establishes a robust foundation for high-performance, low-interference tactile arrays in real-time HMIs.
- 15 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (22) , 41158-41163
Process and Low-Frequency Noise Variability Estimation of Tunable Piezoresistive Sensing Performance in Junctionless Nanowire FETs
- 15 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (22) , 41158-41163
Process and Low-Frequency Noise Variability Estimation of Tunable Piezoresistive Sensing Performance in Junctionless Nanowire FETs
- 20 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 25 (3) , 677-683
Impact of Externally Induced Uniaxial Stress on the Electrical Performance of the Junctionless Nanowire Field-Effect Transistors
The uniaxial tensile mechanical stress (MS) is induced up to 1.4 GPa on the channel of the twin junctionless nanowire (JL-NW) gate-all-around (GAA) field-effect transistors (FETs) using a four-point bending technique. The variation of the electrical parameters is measured before and during induced MS to analyze the performance. The ON-state current, carrier mobility, threshold voltage, and subthreshold swing are directly proportional to the induced MS due to the reduced energy band gap and intervalley scattering effect. The reduced subthreshold swing indicates low power consumption and better switching ability, whereas the higher OFF-state current leads to slightly increased standby power consumption, representing a trade-off for low-power logic applications. In addition, the change of drain current shows highly piezoresistive sensing ability in nanoelectromechanical sensor applications. Thus, this study demonstrates the importance of mechanical stress engineering for performance improvement in non-planar nanowire devices, piezoresistive sensing applications, and device reliability.
- 20 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 25 (3) , 677-683
Impact of Externally Induced Uniaxial Stress on the Electrical Performance of the Junctionless Nanowire Field-Effect Transistors
The uniaxial tensile mechanical stress (MS) is induced up to 1.4 GPa on the channel of the twin junctionless nanowire (JL-NW) gate-all-around (GAA) field-effect transistors (FETs) using a four-point bending technique. The variation of the electrical parameters is measured before and during induced MS to analyze the performance. The ON-state current, carrier mobility, threshold voltage, and subthreshold swing are directly proportional to the induced MS due to the reduced energy band gap and intervalley scattering effect. The reduced subthreshold swing indicates low power consumption and better switching ability, whereas the higher OFF-state current leads to slightly increased standby power consumption, representing a trade-off for low-power logic applications. In addition, the change of drain current shows highly piezoresistive sensing ability in nanoelectromechanical sensor applications. Thus, this study demonstrates the importance of mechanical stress engineering for performance improvement in non-planar nanowire devices, piezoresistive sensing applications, and device reliability.
- 16 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 34 (4) , 362-364
Thermally Stable, BEOL-Configured MEMS-Based One-Time Programmable (OTP) Memory for Cryogenic Embedded Application
In this letter, we demonstrate a MEMS-based one-time programmable(OTP) memory cell integrated into the back-end-of-line (BEOL) layers of a TSMC $0.35~\mu $ m 2P4M CMOS process, designed for operation down to 4 K. This novel design eliminates the need for fusing currents, relying instead on surface-adhesion phenomena for programming. The memory cells operate with a low read voltage of 0.05 V and read current of $80~\mu $ A, ensuring low power consumption and minimal heat generation (~2.8 K). The read resistance ranges from 0.5 to 5.5k $\Omega $ in the logic ‘1’ (ON-state) and ~2.4 T $\Omega $ in the logic ‘0’ (OFF-state), achieving an on-off ratio in the order of $10^{9}$ . The switching energy is limited to 0.5–2.6 pJ, with a demonstrated memory retention of 4 hours at 300, 120, and 4 K. These features make it highly suitable for storing micro-operations permanently in cryogenic embedded applications.[2025-0028]
- 16 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 34 (4) , 362-364
Thermally Stable, BEOL-Configured MEMS-Based One-Time Programmable (OTP) Memory for Cryogenic Embedded Application
In this letter, we demonstrate a MEMS-based one-time programmable(OTP) memory cell integrated into the back-end-of-line (BEOL) layers of a TSMC $0.35~\mu $ m 2P4M CMOS process, designed for operation down to 4 K. This novel design eliminates the need for fusing currents, relying instead on surface-adhesion phenomena for programming. The memory cells operate with a low read voltage of 0.05 V and read current of $80~\mu $ A, ensuring low power consumption and minimal heat generation (~2.8 K). The read resistance ranges from 0.5 to 5.5k $\Omega $ in the logic ‘1’ (ON-state) and ~2.4 T $\Omega $ in the logic ‘0’ (OFF-state), achieving an on-off ratio in the order of $10^{9}$ . The switching energy is limited to 0.5–2.6 pJ, with a demonstrated memory retention of 4 hours at 300, 120, and 4 K. These features make it highly suitable for storing micro-operations permanently in cryogenic embedded applications.[2025-0028]
- 15 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 25 (3) , 567-573
Impact of Electro-Thermal Transport on HCI and BTI Lifetime of Twin Nanowire FETs: Different Operational Modes
Nowadays, electro-thermal transport behavior analyzing is important in emerging nanoscale devices because thermal management is a critical issue in improving the device’s performance and cooling strategies. In this article, a comparative study for electro-thermal performance analysis of junctionless and an inversion-mode nanowire gate-all-around (GAA) field-effect transistors (FETs) is presented in advanced technology nodes by considering nonlocal effects. The junctionless device showed 15.2% better thermal reliability and 26.7%/37.6% better HCI/BTI lifetime compared to the inversion-mode device. The transient behavior of electro-thermal reliability is also investigated for both devices, where the devices turn on for a short time within a duty cycle, the devices showed better thermal reliability and 52.8%/68.2% HCI/BTI lifetime improvement. This study also provides strategies for thermal management in advanced node devices.
- 15 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 25 (3) , 567-573
Impact of Electro-Thermal Transport on HCI and BTI Lifetime of Twin Nanowire FETs: Different Operational Modes
Nowadays, electro-thermal transport behavior analyzing is important in emerging nanoscale devices because thermal management is a critical issue in improving the device’s performance and cooling strategies. In this article, a comparative study for electro-thermal performance analysis of junctionless and an inversion-mode nanowire gate-all-around (GAA) field-effect transistors (FETs) is presented in advanced technology nodes by considering nonlocal effects. The junctionless device showed 15.2% better thermal reliability and 26.7%/37.6% better HCI/BTI lifetime compared to the inversion-mode device. The transient behavior of electro-thermal reliability is also investigated for both devices, where the devices turn on for a short time within a duty cycle, the devices showed better thermal reliability and 52.8%/68.2% HCI/BTI lifetime improvement. This study also provides strategies for thermal management in advanced node devices.
- 7 November 2024
- Published by IOP Publishing in Nanotechnology
- Vol. 36 (4) , 045203
Tunable photo-response in the visible to NIR spectrum range of Germanium-based junctionless nanowire transistor
In this paper, the phototransistor behavior is investigated in the germanium-on-insulator (GeOI)-based junctionless nanowire (JL-NW) transistor under various light conditions. High responsivity and photosensitivity are attributed in the fully depleted regime within the visible and near-infrared bands. The impact of light is also investigated in detail on the electronic and transfer characteristics such as energy bandgap, carrier distribution, electrostatic potential, electric field, generation and recombination rates. Further, the channel doping and thickness are tuned to optimize the optical responsivity. The significant tunability of responsivity is observed with increasing channel thickness. The device exhibits fast optical switching performance, which is further enhanced at higher input light power. Overall, at the nanoscale dimension, our proposed phototransistor demonstrates better detectivity with a significantly smaller illumination area. Thus, the GeOI-based JL-NW phototransistors can be used for imaging (visible wavelength range) and bioimaging (near-infrared wavelength range) applications in advanced technology nodes.
- 7 November 2024
- Published by IOP Publishing in Nanotechnology
- Vol. 36 (4) , 045203
Tunable photo-response in the visible to NIR spectrum range of Germanium-based junctionless nanowire transistor
In this paper, the phototransistor behavior is investigated in the germanium-on-insulator (GeOI)-based junctionless nanowire (JL-NW) transistor under various light conditions. High responsivity and photosensitivity are attributed in the fully depleted regime within the visible and near-infrared bands. The impact of light is also investigated in detail on the electronic and transfer characteristics such as energy bandgap, carrier distribution, electrostatic potential, electric field, generation and recombination rates. Further, the channel doping and thickness are tuned to optimize the optical responsivity. The significant tunability of responsivity is observed with increasing channel thickness. The device exhibits fast optical switching performance, which is further enhanced at higher input light power. Overall, at the nanoscale dimension, our proposed phototransistor demonstrates better detectivity with a significantly smaller illumination area. Thus, the GeOI-based JL-NW phototransistors can be used for imaging (visible wavelength range) and bioimaging (near-infrared wavelength range) applications in advanced technology nodes.
- 17 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (11) , 6659-6664
Capacitorless MEMS-Based Temporary Memory (CMTM) With Extended Refresh Interval
Microelectromechanical system (MEMS)-based mechanical memories are a promising solution in edge devices that require the usage of charge-free storage. Herein this article, we present a capacitorless MEMS-based temporary memory (CMTM) cell offering charge-free storage. This CMTM cell is capable of both memory access and bit storage thereby eliminating the need for multiple elements in a single-bit cell. The implementation of the CMTM cell relies on the structural engineering of the ratio$\xi $ between the surface adhesion force of the contact electrodes (source and drain) and the restoring force supplied by the actuating MEMS structure. Three different memory cells having$\xi $ values of 0.9, 0.7, and 0.6 are designed, fabricated, and tested for harnessing$\xi $ property for temporary storage. Fabricated CMOS-compatible memory cell having$\xi =0.9$ showcases a noteworthy refresh interval ($\tau _{\text {hold}}$ ) of 100 ms. The retention characteristics of the programmed CMTM cell for one second are also demonstrated.- 17 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (11) , 6659-6664
Capacitorless MEMS-Based Temporary Memory (CMTM) With Extended Refresh Interval
Microelectromechanical system (MEMS)-based mechanical memories are a promising solution in edge devices that require the usage of charge-free storage. Herein this article, we present a capacitorless MEMS-based temporary memory (CMTM) cell offering charge-free storage. This CMTM cell is capable of both memory access and bit storage thereby eliminating the need for multiple elements in a single-bit cell. The implementation of the CMTM cell relies on the structural engineering of the ratio$\xi $ between the surface adhesion force of the contact electrodes (source and drain) and the restoring force supplied by the actuating MEMS structure. Three different memory cells having$\xi $ values of 0.9, 0.7, and 0.6 are designed, fabricated, and tested for harnessing$\xi $ property for temporary storage. Fabricated CMOS-compatible memory cell having$\xi =0.9$ showcases a noteworthy refresh interval ($\tau _{\text {hold}}$ ) of 100 ms. The retention characteristics of the programmed CMTM cell for one second are also demonstrated.- 3 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (7) , 4420-4423
Leakage Current and Hot-Carrier Injection in the Junctionless Nanowire FETs Enhanced by Tensile Mechanical Stress
In this brief, the gate-induced drain leakage (GIDL) current and hot-carrier injection (HCI) in the twin junctionless nanowire (JL-NW) gate-all-around (GAA) field-effect transistor (FET) is investigated with induced mechanical stress (MS) from few MPa to GPa level. GIDL is observed to exponentially increase with induced MS, a consequence of the decrease in the bandgap and effective mass, which leads to high band-to-band tunneling (BTBT). However, the induced MS enhances the impact ionization and secondary electron-hole pair generation, and some hot electrons are trapped into the gate oxide, causing the HCI and gate leakage current to increase almost linearly. The study highlights the importance of MS in device reliability.
- 3 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (7) , 4420-4423
Leakage Current and Hot-Carrier Injection in the Junctionless Nanowire FETs Enhanced by Tensile Mechanical Stress
In this brief, the gate-induced drain leakage (GIDL) current and hot-carrier injection (HCI) in the twin junctionless nanowire (JL-NW) gate-all-around (GAA) field-effect transistor (FET) is investigated with induced mechanical stress (MS) from few MPa to GPa level. GIDL is observed to exponentially increase with induced MS, a consequence of the decrease in the bandgap and effective mass, which leads to high band-to-band tunneling (BTBT). However, the induced MS enhances the impact ionization and secondary electron-hole pair generation, and some hot electrons are trapped into the gate oxide, causing the HCI and gate leakage current to increase almost linearly. The study highlights the importance of MS in device reliability.
- 31 May 2024
- Published by Springer Nature
- p. 311-318
Ultrasensitive Reduced Vanadium Dioxide-Based MEMS Pirani Gauge with Extended Dynamic Range
- 31 May 2024
- Published by Springer Nature
- p. 311-318
Ultrasensitive Reduced Vanadium Dioxide-Based MEMS Pirani Gauge with Extended Dynamic Range