Zehong Yan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Zehong Yan has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Fangfang Fan
National Key Laboratory of Antenna and Microwave Technology, Xidian University, Xian, China
15 shared publications - Enlin Wang
School of Integrated Circuits, Nanjing University of Aeronautics and Astronautics, Nanjing, China
8 shared publications - Mingbo Cai
National Key Laboratory of Antennas and Microwave Technology, xidian university, Xian, China
8 shared publications - Shuyang Yang
Key Laboratory of Antennas and Microwave Technology, Xidian University, Xian, China
8 shared publications - Xiaofei Zhao
National Key Laboratory of Radar Detection and Sensing, Xian, China
8 shared publications - Tianling Zhang
National Key Laboratory of Radar Detection and Sensing, Xidian University, Xi’an 710071, China
7 shared publications
Latest Publications
- 12 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. PP (15361225) , 1-5
A Function-Decoupled and Layer-Synergized Metasurface Antenna for Low-Profile Bidirectional CP Multibeam Generation
This paper proposes a novel function-decoupled and layer synergized metasurface antenna (FDLS-MA) to address the challenge of generating two independently controlled orthogonal circularly polarized beams in each of the ±z directions under low-profile constraints. The metasurface unit cells adopt a receiver–transmitter structure, where polarization configuration and patch rotation provide phase control. The middle multifunctional core layer (MC#1) performs polarization routing and provides phase compensation for asymmetric dual-path folding, enabling bidirectional profile reduction. The upper and lower dual-beamforming layers (DDBF#1 and DDBF#2) generate orthogonal circularly polarized beams in the +z and −z directions, respectively. The proposed antenna enables independent control of four beams and supports flexible bidirectional profile compression. At 9.5 GHz, a prototype achieves peak gains of 17.5–18.6 dBi, a total aperture efficiency of 46.4%, and a profile height of 2 3 F. The proposed design provides a scalable framework for low-profile, bidirectional, and independently controllable multibeam antennas.
- 12 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. PP (15361225) , 1-5
A Function-Decoupled and Layer-Synergized Metasurface Antenna for Low-Profile Bidirectional CP Multibeam Generation
This paper proposes a novel function-decoupled and layer synergized metasurface antenna (FDLS-MA) to address the challenge of generating two independently controlled orthogonal circularly polarized beams in each of the ±z directions under low-profile constraints. The metasurface unit cells adopt a receiver–transmitter structure, where polarization configuration and patch rotation provide phase control. The middle multifunctional core layer (MC#1) performs polarization routing and provides phase compensation for asymmetric dual-path folding, enabling bidirectional profile reduction. The upper and lower dual-beamforming layers (DDBF#1 and DDBF#2) generate orthogonal circularly polarized beams in the +z and −z directions, respectively. The proposed antenna enables independent control of four beams and supports flexible bidirectional profile compression. At 9.5 GHz, a prototype achieves peak gains of 17.5–18.6 dBi, a total aperture efficiency of 46.4%, and a profile height of 2 3 F. The proposed design provides a scalable framework for low-profile, bidirectional, and independently controllable multibeam antennas.
- Open Access
- 3 April 2026
- Published by MDPI AG in Electronics
- Vol. 15 (7) , 1505
Design and Development of a Multi-Channel High-Frequency Switch Matrix
To meet the increasingly strict requirements of modern communication, radar detection and electronic measurement systems for wide-bandwidth, low-insertion-loss and high-isolation signal routing, this paper presents a 16 × 16 programmable switch matrix that simultaneously achieves wideband operation (DC-40 GHz), low insertion loss (≤0.9 dB maximum), high isolation (>50 dB typical), and systematic modular scalability, a combination not found in existing implementations. The matrix, constructed with high-quality coaxial switches and optimized RF circuitry and electromagnetic structures, provides flexible and stable single-pole multi-throw (SPMT) signal routing across an ultra-wide frequency range from DC to 40 GHz. The switch matrix features a modular architecture, integrating multiple RF switching units, drive control circuits, and communication interface modules. This architecture achieves minimal signal path depth while maintaining full connectivity between any input and output port, directly minimizing cumulative insertion loss. Through precise impedance matching design and isolation structure optimization, the system still exhibits outstanding transmission characteristics at the 40 GHz high-frequency end: typical insertion loss does not exceed 0.9 dB, and the isolation between channels is better than 50 dB, effectively ensuring the integrity of signals in complex multi-channel environments. To meet the requirements of automated testing and remote control, the equipment integrates dual communication interfaces (serial port/network port), supports the SCPI command set and TCP/IP protocol, and can be conveniently embedded in various test platforms to achieve instrument interconnection and test process automation. Experimental verification shows that this matrix exhibits excellent switching stability and signal consistency across the entire 40 GHz, with a switching action time of less than 10 ms. Furthermore, it is capable of real-time topology reconfiguration via a microcontroller or FPGA. These innovations collectively deliver a switch matrix that meets the demanding requirements of 5G communication, millimeter-wave radar, and aerospace defense systems—applications where bandwidth, signal integrity, and system flexibility are paramount.
- 3 April 2026
- Published by MDPI AG in Electronics
- Vol. 15 (7) , 1505
Open AccessDesign and Development of a Multi-Channel High-Frequency Switch Matrix
To meet the increasingly strict requirements of modern communication, radar detection and electronic measurement systems for wide-bandwidth, low-insertion-loss and high-isolation signal routing, this paper presents a 16 × 16 programmable switch matrix that simultaneously achieves wideband operation (DC-40 GHz), low insertion loss (≤0.9 dB maximum), high isolation (>50 dB typical), and systematic modular scalability, a combination not found in existing implementations. The matrix, constructed with high-quality coaxial switches and optimized RF circuitry and electromagnetic structures, provides flexible and stable single-pole multi-throw (SPMT) signal routing across an ultra-wide frequency range from DC to 40 GHz. The switch matrix features a modular architecture, integrating multiple RF switching units, drive control circuits, and communication interface modules. This architecture achieves minimal signal path depth while maintaining full connectivity between any input and output port, directly minimizing cumulative insertion loss. Through precise impedance matching design and isolation structure optimization, the system still exhibits outstanding transmission characteristics at the 40 GHz high-frequency end: typical insertion loss does not exceed 0.9 dB, and the isolation between channels is better than 50 dB, effectively ensuring the integrity of signals in complex multi-channel environments. To meet the requirements of automated testing and remote control, the equipment integrates dual communication interfaces (serial port/network port), supports the SCPI command set and TCP/IP protocol, and can be conveniently embedded in various test platforms to achieve instrument interconnection and test process automation. Experimental verification shows that this matrix exhibits excellent switching stability and signal consistency across the entire 40 GHz, with a switching action time of less than 10 ms. Furthermore, it is capable of real-time topology reconfiguration via a microcontroller or FPGA. These innovations collectively deliver a switch matrix that meets the demanding requirements of 5G communication, millimeter-wave radar, and aerospace defense systems—applications where bandwidth, signal integrity, and system flexibility are paramount.
- 25 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (12) , 8991-9001
High-Order Resonating Cavity-Backed Slot Antenna Array Based on Contactless Air-Filled Substrate-Integrated Waveguide and Transition to Inverted Grounded Coplanar Gap Waveguide
A contactless planar slot antenna array is proposed in this paper with high realized radiation efficiency. To simplify the feeding network, slot elements in subarray are excited by the back cavity with a high-order resonating mode (the TE 430 mode). To reduce the loss and increase the efficiency, entire antenna array, including the resonating cavity and feeding network, is realized by low-loss contactless air-filled substrate integrated waveguide (CLAF-SIW). In addition, inverted grounded coplanar gap waveguide (IGCPGW) is firstly proposed for measurements, using the contactless ridge substrate integrated waveguide (CLRSIW) as the transition to connect the CLAF-SIW. A 8×6 slot array with 2×2 subarrays is fabricated and fastened only by metal screws. From 36.92GHz to 40GHz, the measured reflection coefficient is better than -10dB and the realized radiation efficiency is greater than 78.6%. The measured peak realized radiation efficiency is 89.4% at 38GHz.
- 25 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (12) , 8991-9001
High-Order Resonating Cavity-Backed Slot Antenna Array Based on Contactless Air-Filled Substrate-Integrated Waveguide and Transition to Inverted Grounded Coplanar Gap Waveguide
A contactless planar slot antenna array is proposed in this paper with high realized radiation efficiency. To simplify the feeding network, slot elements in subarray are excited by the back cavity with a high-order resonating mode (the TE 430 mode). To reduce the loss and increase the efficiency, entire antenna array, including the resonating cavity and feeding network, is realized by low-loss contactless air-filled substrate integrated waveguide (CLAF-SIW). In addition, inverted grounded coplanar gap waveguide (IGCPGW) is firstly proposed for measurements, using the contactless ridge substrate integrated waveguide (CLRSIW) as the transition to connect the CLAF-SIW. A 8×6 slot array with 2×2 subarrays is fabricated and fastened only by metal screws. From 36.92GHz to 40GHz, the measured reflection coefficient is better than -10dB and the realized radiation efficiency is greater than 78.6%. The measured peak realized radiation efficiency is 89.4% at 38GHz.
- 13 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (4) , 3081-3091
Differentially-Fed Slot Array Antenna Backed With High-Order Resonating Cavity Loading Slow-Wave Top–Bottom Double Pins
A novel slot array antenna based on a rectangular waveguide (RWG) cavity using the high-order resonating mode is introduced in this paper. A TE 440 -mode radiation cavity is used to excite 4×4 radiation slot elements with a specific distribution that ensures in-phase fields. To achieve a wide 1-dB gain bandwidth, slow-wave top-bottom double pins (TBDPs) are positioned near the radiation slots within the radiation cavity. This helps to simultaneously improve directivity, impedance matching and eliminate grating lobes. A differential feeding strategy is deployed, employing the TE 120 -mode feeding cavity to excite both coupling slots with identical amplitude and 180° phase difference. The measurement and simulation results of the proposed cavity-backed slot antenna are in good agreement. The measured results reveal notable achievements, including an impedance bandwidth (|S 11 |<-10 dB) of 9% (14.2 to 15.54 GHz), and a 1-dB gain bandwidth of 8.05% (14.3 to 15.5 GHz). Furthermore, the measured peak realized gain is 18.87dBi and the maximum realized aperture efficiency is 86.2%.
- 13 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (4) , 3081-3091
Differentially-Fed Slot Array Antenna Backed With High-Order Resonating Cavity Loading Slow-Wave Top–Bottom Double Pins
A novel slot array antenna based on a rectangular waveguide (RWG) cavity using the high-order resonating mode is introduced in this paper. A TE 440 -mode radiation cavity is used to excite 4×4 radiation slot elements with a specific distribution that ensures in-phase fields. To achieve a wide 1-dB gain bandwidth, slow-wave top-bottom double pins (TBDPs) are positioned near the radiation slots within the radiation cavity. This helps to simultaneously improve directivity, impedance matching and eliminate grating lobes. A differential feeding strategy is deployed, employing the TE 120 -mode feeding cavity to excite both coupling slots with identical amplitude and 180° phase difference. The measurement and simulation results of the proposed cavity-backed slot antenna are in good agreement. The measured results reveal notable achievements, including an impedance bandwidth (|S 11 |<-10 dB) of 9% (14.2 to 15.54 GHz), and a 1-dB gain bandwidth of 8.05% (14.3 to 15.5 GHz). Furthermore, the measured peak realized gain is 18.87dBi and the maximum realized aperture efficiency is 86.2%.
- 19 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (1) , 221-233
Contactless Air-Filled Substrate Integrated Cavity-Backed Slot Antenna Array With Improved Printed Ridge Gap Waveguide Feeding Network
A contactless air-filled substrate integrated cavity-backed slot antenna array is designed utilizing gap waveguide technology in this paper. To enhance realized aperture efficiency, a contactless air-filled substrate integrated waveguide (CLAF-SIW) is implemented to construct a TE210-mode resonance cavity for feeding 2×2 slot elements. Moreover, an improved printed ridge gap waveguide (I-PRGW) is proposed for the first time to achieve the feeding network for feeding each air-filled resonator cavity uniformly with the same amplitude and phase. In order to mitigate the sensitivity of the antenna to the relative position between the coupling slot and the feed transmission line, the shielded stripline is integrated on the same dielectric layer as the coupling slot. Furthermore, the shielded stripline serves as the transition from the I-PRGW to the grounded coplanar waveguide (GCPW) for measurement. A physical prototype of the antenna array, comprising 4×4 slot elements, is manufactured. Experimental results demonstrate that the proposed antenna array, incorporating the transition structure, exhibits a wide impedance bandwidth ranging from 28.3GHz to 40GHz with a reflection coefficient better than -10dB, corresponding to a fractional bandwidth of 34.3%. The maximum realized boresight gain is measured to be 20.02 dBi at 38GHz, while achieving a maximum realized aperture efficiency of 67.8%.
- 19 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (1) , 221-233
Contactless Air-Filled Substrate Integrated Cavity-Backed Slot Antenna Array With Improved Printed Ridge Gap Waveguide Feeding Network
A contactless air-filled substrate integrated cavity-backed slot antenna array is designed utilizing gap waveguide technology in this paper. To enhance realized aperture efficiency, a contactless air-filled substrate integrated waveguide (CLAF-SIW) is implemented to construct a TE210-mode resonance cavity for feeding 2×2 slot elements. Moreover, an improved printed ridge gap waveguide (I-PRGW) is proposed for the first time to achieve the feeding network for feeding each air-filled resonator cavity uniformly with the same amplitude and phase. In order to mitigate the sensitivity of the antenna to the relative position between the coupling slot and the feed transmission line, the shielded stripline is integrated on the same dielectric layer as the coupling slot. Furthermore, the shielded stripline serves as the transition from the I-PRGW to the grounded coplanar waveguide (GCPW) for measurement. A physical prototype of the antenna array, comprising 4×4 slot elements, is manufactured. Experimental results demonstrate that the proposed antenna array, incorporating the transition structure, exhibits a wide impedance bandwidth ranging from 28.3GHz to 40GHz with a reflection coefficient better than -10dB, corresponding to a fractional bandwidth of 34.3%. The maximum realized boresight gain is measured to be 20.02 dBi at 38GHz, while achieving a maximum realized aperture efficiency of 67.8%.
- 18 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (11) , 1580-1583
Low-Cost Ball-Pen Gap Waveguide With Nearly Zero Friction for Sliding Movements
This letter presents a novel easy-to-manufacture ball-pen gap waveguide (GW) by utilizing commercial low-cost ball pens to have mechanical reconfigurability. The proposed ball-pen GW consists of a perforated bottom metal plate with ball pens’ tips inserted and a flat top plate. Compared with the other noncontact GWs with bed-of-pins structures obtained by milling, the realization of the new ball-pen GW requires only drilling holes on the bottom plate for inserting ball-pen tips to obtain the electromagnetic bandgap property, making it low cost. The more important advantage of the ball-pen GW is to make use of the balls of the ball-pen tips to realize smooth low-friction sliding movements for the mechanical reconfiguration. For the sake of verification, a double 90 $^\circ$ bend of the ball-pen GW has been designed, manufactured, and measured. Both simulated and measured results demonstrate its excellent transmission performance and the movable property.
- 18 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (11) , 1580-1583
Low-Cost Ball-Pen Gap Waveguide With Nearly Zero Friction for Sliding Movements
This letter presents a novel easy-to-manufacture ball-pen gap waveguide (GW) by utilizing commercial low-cost ball pens to have mechanical reconfigurability. The proposed ball-pen GW consists of a perforated bottom metal plate with ball pens’ tips inserted and a flat top plate. Compared with the other noncontact GWs with bed-of-pins structures obtained by milling, the realization of the new ball-pen GW requires only drilling holes on the bottom plate for inserting ball-pen tips to obtain the electromagnetic bandgap property, making it low cost. The more important advantage of the ball-pen GW is to make use of the balls of the ball-pen tips to realize smooth low-friction sliding movements for the mechanical reconfiguration. For the sake of verification, a double 90 $^\circ$ bend of the ball-pen GW has been designed, manufactured, and measured. Both simulated and measured results demonstrate its excellent transmission performance and the movable property.
- Open Access
- 29 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 35984-35992
A Dual-Polarized Broadband High Gain Base Station Antenna With an Octagonal Structure
In this paper, a dual-polarized broadband high gain base station antenna unit is proposed. The antenna unit comprises an octagonal radiation structure and a pair of orthogonal Γ-shaped feeding structure, stacked patch and metal reflection structure. The octagonal radiation structure can effectively increase the radiation area, and the wide working frequency band can be realized by means of coupling and slotting. At the same time, high isolation and stable radiation pattern characteristics can be obtained. The simulation results show that the impedance bandwidth of the antenna is 47% (1.67 - 2.69 GHz) when the reflection coefficient is less than - 20 dB, and the port isolation is greater than 27 dB, a high gain of 10 ± 0.5 dBi can be obtained in the passband. Furthermore, the antenna also obtains a wide half power beam width (HPBW). The HPBW fed through a single port and two ports are around 60°. Finally, the antenna unit is applied to the 4 × 11 antenna array to realize the multi-band dual polarization system.
- 29 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 35984-35992
Open AccessA Dual-Polarized Broadband High Gain Base Station Antenna With an Octagonal Structure
In this paper, a dual-polarized broadband high gain base station antenna unit is proposed. The antenna unit comprises an octagonal radiation structure and a pair of orthogonal Γ-shaped feeding structure, stacked patch and metal reflection structure. The octagonal radiation structure can effectively increase the radiation area, and the wide working frequency band can be realized by means of coupling and slotting. At the same time, high isolation and stable radiation pattern characteristics can be obtained. The simulation results show that the impedance bandwidth of the antenna is 47% (1.67 - 2.69 GHz) when the reflection coefficient is less than - 20 dB, and the port isolation is greater than 27 dB, a high gain of 10 ± 0.5 dBi can be obtained in the passband. Furthermore, the antenna also obtains a wide half power beam width (HPBW). The HPBW fed through a single port and two ports are around 60°. Finally, the antenna unit is applied to the 4 × 11 antenna array to realize the multi-band dual polarization system.
- 15 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (7) , 999-1002
E-Band Low-Loss Reconfigurable Phase Shifters
Two types of low-loss mechanically reconfigurable phase shifters at E-band based on gap waveguide (GW) technology, the GW slow wave and the GW width-variation, are proposed in this letter. Phase shifts are achieved by mechanical movements. To avoid wave leakage and undesired resonances during the movement, quasi-PEC-AMC structures are implemented. The phase shifters have been fabricated and measured. The results show that the insertion losses are about 0.4 and 0.3 dB, and the reflection coefficients are better than $-$ 13 and $-$ 15 dB for the slow wave and the width variation, respectively, over 71–86 GHz.
- 15 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (7) , 999-1002
E-Band Low-Loss Reconfigurable Phase Shifters
Two types of low-loss mechanically reconfigurable phase shifters at E-band based on gap waveguide (GW) technology, the GW slow wave and the GW width-variation, are proposed in this letter. Phase shifts are achieved by mechanical movements. To avoid wave leakage and undesired resonances during the movement, quasi-PEC-AMC structures are implemented. The phase shifters have been fabricated and measured. The results show that the insertion losses are about 0.4 and 0.3 dB, and the reflection coefficients are better than $-$ 13 and $-$ 15 dB for the slow wave and the width variation, respectively, over 71–86 GHz.
- 10 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (4) , 3707-3712
Multibeam Forming With Arbitrary Radiation Power Ratios Based on a Conformal Amplitude–Phase-Controlled Metasurface
In this communication, we present a novel amplitude-phase-controlled metasurface (APCMS), which features a full 2π. phase coverage and amplitude variation from 0 to 1 for transmissive waves. By alternately cascading three ultrathin printed circuit boards (PCBs) and two curved 3D-printed substrates, the proposed APCMS is designed to be a cambered surface and can be applied to certain space-constrained scenarios. Different from phase-only controlled MSs, with the ability to impart a new degree of freedom, we use the APCMS to construct a spatial power divider by superimposing multiple aperture fields assigned to amplitude weighting coefficients. As a proof-of-concept example, two quarter-cylindrical APCMS-based spatial power dividers are designed to generate equal-power and unequal-power triple-beam radiation patterns at different and same elevation angles, respectively. A prototype of an equal-power divider is fabricated and measured to verify the proposed strategy. The results show that upon illumination of a feed horn, the maximum difference among the realized gains of the three beams is less than 0.9 dB at 12 GHz. Their 3-dB gain bandwidths are 26.7%, 19.5%, and 23.3%. Our study holds potential applications in multibeam shaping and multiple target tracking systems.
- 10 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (4) , 3707-3712
Multibeam Forming With Arbitrary Radiation Power Ratios Based on a Conformal Amplitude–Phase-Controlled Metasurface
In this communication, we present a novel amplitude-phase-controlled metasurface (APCMS), which features a full 2π. phase coverage and amplitude variation from 0 to 1 for transmissive waves. By alternately cascading three ultrathin printed circuit boards (PCBs) and two curved 3D-printed substrates, the proposed APCMS is designed to be a cambered surface and can be applied to certain space-constrained scenarios. Different from phase-only controlled MSs, with the ability to impart a new degree of freedom, we use the APCMS to construct a spatial power divider by superimposing multiple aperture fields assigned to amplitude weighting coefficients. As a proof-of-concept example, two quarter-cylindrical APCMS-based spatial power dividers are designed to generate equal-power and unequal-power triple-beam radiation patterns at different and same elevation angles, respectively. A prototype of an equal-power divider is fabricated and measured to verify the proposed strategy. The results show that upon illumination of a feed horn, the maximum difference among the realized gains of the three beams is less than 0.9 dB at 12 GHz. Their 3-dB gain bandwidths are 26.7%, 19.5%, and 23.3%. Our study holds potential applications in multibeam shaping and multiple target tracking systems.
- 26 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 22 (2) , 283-287
A Wideband Compact Printed Dipole Antenna Array With SICL Feeding Network for 5G Application
A wideband compact printed dipole antenna array with an element size of 0.16 λ 0 × 0.34 λ 0 is proposed for millimeter-wave (mmW) applications, particularly for 5G applications. The two patches of the dipole are printed on two different layers to achieve a wide bandwidth of 50% (24-40 GHz) for SWR < 2. Ground-signal-ground (GSG) transmission line construction with a height difference between the feeding via and the two shorting vias is employed to achieve a relatively symmetrical radiation pattern. An antenna array consisting of the proposed antenna and a 1 to 8 substrate-integrated coaxial line (SICL) feeding network is fabricated and measured. Simulations are also used to verify the beam scanning performance (up to ±50°). The proposed compact printed dipole antenna is a good contender for 5G mmW applications due to its wide band, compact size, and good beam scanning performance.
- 26 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 22 (2) , 283-287
A Wideband Compact Printed Dipole Antenna Array With SICL Feeding Network for 5G Application
A wideband compact printed dipole antenna array with an element size of 0.16 λ 0 × 0.34 λ 0 is proposed for millimeter-wave (mmW) applications, particularly for 5G applications. The two patches of the dipole are printed on two different layers to achieve a wide bandwidth of 50% (24-40 GHz) for SWR < 2. Ground-signal-ground (GSG) transmission line construction with a height difference between the feeding via and the two shorting vias is employed to achieve a relatively symmetrical radiation pattern. An antenna array consisting of the proposed antenna and a 1 to 8 substrate-integrated coaxial line (SICL) feeding network is fabricated and measured. Simulations are also used to verify the beam scanning performance (up to ±50°). The proposed compact printed dipole antenna is a good contender for 5G mmW applications due to its wide band, compact size, and good beam scanning performance.