Volodymyr Klitnoi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Volodymyr Klitnoi has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Anatoliy Gaydamaka
National Technical University “Kharkiv Polytechnic Institute
8 shared publications - Andrew Ruzmetov
National Technical University Princeton University «Kharkiv Polytechnic Institute
3 shared publications - Yuriy Muzikin
National Technical University “Kharkiv Polytechnic Institute
3 shared publications - Dmytro Borodin
Machine Components and Hydropneumatic Systems Department; National Technical University “Kharkiv Polytechnic Institute
2 shared publications - Gennady Kulik
National Technical University “Kharkiv Polytechnic Institute
2 shared publications - Oleksandr Bobovnikov
National technical university «Kharkiv polytechnic institute
2 shared publications
Latest Publications
- Open Access
- 29 June 2026
- Published by Polskie Towarzystwo Diagnostyki Technicznej in Diagnostyka
- Vol. 27 (2) , 1-12
Machine learning-based diagnosis of sliding bearings in rolling mill drive systems under severe operating conditions
- 29 June 2026
- Published by Polskie Towarzystwo Diagnostyki Technicznej in Diagnostyka
- Vol. 27 (2) , 1-12
Open AccessMachine learning-based diagnosis of sliding bearings in rolling mill drive systems under severe operating conditions
- Open Access
- 1 June 2026
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1638 (1)
Technical condition control of large-module gears by tooth hardness measurements
This paper presents an experimental verification of the applicability of a developed method for monitoring the technical condition of large-module gears based on tooth hardness measurements under operating conditions, both without dismantling and with dismantling of the gearbox. The method is based on hardness measurements performed on tooth end faces, which enable condition monitoring throughout the regulated service life without dismantling, as well as on hardness measurements of working tooth surfaces after dismantling. Experimental investigations conducted on a spur gearbox with four drive motors of the Slabbing-1150 rolling mill revealed a systematic increase in hardness of both tooth end faces and working surfaces. The scientific novelty of the study lies in substantiating the feasibility of technical condition assessment of large-module gears using the proposed hardness-based methodology. The practical significance of the results consists in establishing a foundation for the development of residual life prediction methods for heavily loaded large-module gears.
- 1 June 2026
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1638 (1)
Open AccessTechnical condition control of large-module gears by tooth hardness measurements
This paper presents an experimental verification of the applicability of a developed method for monitoring the technical condition of large-module gears based on tooth hardness measurements under operating conditions, both without dismantling and with dismantling of the gearbox. The method is based on hardness measurements performed on tooth end faces, which enable condition monitoring throughout the regulated service life without dismantling, as well as on hardness measurements of working tooth surfaces after dismantling. Experimental investigations conducted on a spur gearbox with four drive motors of the Slabbing-1150 rolling mill revealed a systematic increase in hardness of both tooth end faces and working surfaces. The scientific novelty of the study lies in substantiating the feasibility of technical condition assessment of large-module gears using the proposed hardness-based methodology. The practical significance of the results consists in establishing a foundation for the development of residual life prediction methods for heavily loaded large-module gears.
- Open Access
- 21 May 2026
- Published by European Alliance for Innovation n.o. in EAI Endorsed Transactions on Digital Transformation of Industrial Processes
- Vol. 2 (1)
Modern Approaches to Monitoring the Technical Condition of Heavy-Duty Gears
INTRODUCTION: Gear transmissions of heavy-duty drive reducers operate under variable loads that cause fatigue damage (pitting and tooth fracture), therefore effective condition monitoring is essential to prevent failures.. OBJECTIVES: To conduct a review of the directions and methods for monitoring the technical condition of gearbox gears, to select an appropriate monitoring approach for the gears of high-power machine drives, and to propose the most effective method taking into account operating conditions and gear tooth control zones. METHODS: The research employs an instrumental monitoring approach based on measuring the surface hardness of gear teeth using portable hardness testers. The methodology involves comparative analysis of metal hardness in two critical zones: the tooth end faces and the working surfaces. RESULTS: Based on the conducted review, a method for monitoring the technical condition of gearbox gears in high-power drives has been developed. This method can be applied both in workshop and field operating conditions, enabling inspection of the working and non-working tooth surfaces with or without gearbox disassembly. CONCLUSION: The developed monitoring method for gearbox gears of high-power drives will serve as a foundation for the development of a method for predicting the remaining service life of gearbox gears in high-power machine drives
- 21 May 2026
- Published by European Alliance for Innovation n.o. in EAI Endorsed Transactions on Digital Transformation of Industrial Processes
- Vol. 2 (1)
Open AccessModern Approaches to Monitoring the Technical Condition of Heavy-Duty Gears
INTRODUCTION: Gear transmissions of heavy-duty drive reducers operate under variable loads that cause fatigue damage (pitting and tooth fracture), therefore effective condition monitoring is essential to prevent failures.. OBJECTIVES: To conduct a review of the directions and methods for monitoring the technical condition of gearbox gears, to select an appropriate monitoring approach for the gears of high-power machine drives, and to propose the most effective method taking into account operating conditions and gear tooth control zones. METHODS: The research employs an instrumental monitoring approach based on measuring the surface hardness of gear teeth using portable hardness testers. The methodology involves comparative analysis of metal hardness in two critical zones: the tooth end faces and the working surfaces. RESULTS: Based on the conducted review, a method for monitoring the technical condition of gearbox gears in high-power drives has been developed. This method can be applied both in workshop and field operating conditions, enabling inspection of the working and non-working tooth surfaces with or without gearbox disassembly. CONCLUSION: The developed monitoring method for gearbox gears of high-power drives will serve as a foundation for the development of a method for predicting the remaining service life of gearbox gears in high-power machine drives
- 1 October 2025
- Published by Springer Nature
- p. 204-214
The Technical Condition Monitoring Model of Large Module Gears
- 1 October 2025
- Published by Springer Nature
- p. 204-214
The Technical Condition Monitoring Model of Large Module Gears
- Open Access
- 17 July 2025
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University «KhPI». Series: Automobile and Tractor Construction
- No. 1,p. 12-19
STRUCTURAL AND FUNCTIONAL MODEL OF BEARING ASSEMBLIES IN LOAD-BEARING UNITS OF RAIL TRANSPORT SYSTEMS
The type of roller bearings used in axleboxes (supporting units) of rail transport systems (RBSRT) varies depending on the operating conditions specific to each country. In the United Kingdom, the United States, Japan, and Poland, railcars are equipped with wheelsets fitted with double-row tapered roller bearings. In Austria, Germany, and Ukraine, bearing units typically comprise two cylindrical roller bearings, while in Sweden, axlebox assemblies with two spherical roller bearings are standard. For structural and functional analysis, the most common series-produced cylindrical RBSRT units used in Ukrainian freight and passenger rolling stock—representing nearly 99% of the total—were selected as the baseline design. A structural decomposition of the primary bearing assemblies was performed in accordance with their functional roles. Based on the developed structural and functional model of the cylindrical roller bearing, functional interrelations between the bearing components were identified. The analysis focused particularly on the functions of the cage (separator), including prevention of skewing, reduction of interaction forces with the rollers and bearing ring, and minimization of roller slippage. These insights supported the rationale for design modifications of the cage—specifically, increasing the number of windows, altering the shape of the side surfaces of the bridges, and optimizing the cross-section of the cage rings—to enhance the technical performance of RBSRT while maintaining dimensional compatibility.
- 17 July 2025
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University «KhPI». Series: Automobile and Tractor Construction
- No. 1,p. 12-19
Open AccessSTRUCTURAL AND FUNCTIONAL MODEL OF BEARING ASSEMBLIES IN LOAD-BEARING UNITS OF RAIL TRANSPORT SYSTEMS
The type of roller bearings used in axleboxes (supporting units) of rail transport systems (RBSRT) varies depending on the operating conditions specific to each country. In the United Kingdom, the United States, Japan, and Poland, railcars are equipped with wheelsets fitted with double-row tapered roller bearings. In Austria, Germany, and Ukraine, bearing units typically comprise two cylindrical roller bearings, while in Sweden, axlebox assemblies with two spherical roller bearings are standard. For structural and functional analysis, the most common series-produced cylindrical RBSRT units used in Ukrainian freight and passenger rolling stock—representing nearly 99% of the total—were selected as the baseline design. A structural decomposition of the primary bearing assemblies was performed in accordance with their functional roles. Based on the developed structural and functional model of the cylindrical roller bearing, functional interrelations between the bearing components were identified. The analysis focused particularly on the functions of the cage (separator), including prevention of skewing, reduction of interaction forces with the rollers and bearing ring, and minimization of roller slippage. These insights supported the rationale for design modifications of the cage—specifically, increasing the number of windows, altering the shape of the side surfaces of the bridges, and optimizing the cross-section of the cage rings—to enhance the technical performance of RBSRT while maintaining dimensional compatibility.
- 11 June 2025
- Published by Springer Nature
- p. 171-181
Modeling of Vibration Isolation System Using Quasi-Zero Stiffness with Adaptive Piezoceramic Elements
- 11 June 2025
- Published by Springer Nature
- p. 171-181
Modeling of Vibration Isolation System Using Quasi-Zero Stiffness with Adaptive Piezoceramic Elements
- Open Access
- 1 February 2025
- Published by Polskie Towarzystwo Diagnostyki Technicznej in Diagnostyka
- Vol. 26 (1) , 1-9
Study of the functioning and wear of the teeth of the intermediate gear of the vertical gearbox rolls of the slabing state - 1150
Gears with large modules are widely used in heavy engineering, for example in rolling mills. The unpredictability of mechanical equipment overloads or operator error lead to premature failure, first of all, of typical parts like gear wheels. This article analyzes the nature of the wear of the...
- 1 February 2025
- Published by Polskie Towarzystwo Diagnostyki Technicznej in Diagnostyka
- Vol. 26 (1) , 1-9
Open AccessStudy of the functioning and wear of the teeth of the intermediate gear of the vertical gearbox rolls of the slabing state - 1150
Gears with large modules are widely used in heavy engineering, for example in rolling mills. The unpredictability of mechanical equipment overloads or operator error lead to premature failure, first of all, of typical parts like gear wheels. This article analyzes the nature of the wear of the...
- 9 August 2023
- Published by Springer Nature
- p. 285-297
Modelling of Technical Condition Control of Heavy Loaded Gears Teeth
- 9 August 2023
- Published by Springer Nature
- p. 285-297
Modelling of Technical Condition Control of Heavy Loaded Gears Teeth