YZYiran Zhou

Yiran Zhou

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yiran Zhou has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Nanosized κ-Carbide and B2 Boosting Strength Without Sacrificing Ductility in a Low-Density Fe-32Mn-11Al Steel

    by Changwei He, Yongfeng Shen, Wenying Xue, Zhijian Fan, Yiran Zhou

    High-performance lightweight materials are urgently needed because of energy savings and emission reduction. Here, we design a new steel with a low density of 6.41 g/cm3, which is a 20% weight reduction compared to the conventional steel. The mechanical properties and microstructures of the steels prepared with different routes are systematically explored by utilizing uniaxial tensile testing and transmission electron microscopy. The steel processed by cold rolling and recrystallization annealing at 950 °C for 15 min shows an ultra-high yield strength of 1241 ± 10 MPa, while retaining a good ductility of 38 ± 1%. The high yield strength is mainly related to the synergistic precipitation strengthening introduced by nanoscale B2 and κ′-carbides. It is encouraging to notice that the yield strength increased without scarifying ductility, compared to the ST steel. The key reason is that the high strain hardening rate is activated by combined factors, including the blockage of numerous twins and nanoscale B2 to the dislocation movements, and dynamic slip band refinement. This study is instructive for concurrently enhancing the strength and ductility of austenitic lightweight steels with fully recrystallized grains and dual nano-precipitates.


  • Open Access

    Multi-Step Gold Refinement and Collection Using Bi-Minerals in the Laozuoshan Gold Deposit, NE China

    by Lin Meng, Fei Huang, Wenyuan Gao, Rongzhen Gao, Fude Zhao, Yiran Zhou, Yongli Li

    Gold and Bi-bearing parageneses are pivotal to understanding gold concentration and deposition processes. The large-scale Laozuoshan gold deposit is located in the Jiamusi Block, northeastern China, and has experienced complex mineralization processes with abundant gold and Bi-bearing minerals. However, the relationship between Bi-minerals and gold is unclear, preventing our understanding of the gold enrichment and precipitation mechanism in the Laozuoshan gold deposit. Optical microscope and SEM results show three stages of gold mineralization: pyrrhotite (Po-1) + arsenopyrite (Apy-1) + Bi-bearing minerals (Bis-1) + Au-1; arsenopyrite (Apy-2) + chlorite + Bi-bearing minerals (Bis-2) + Au-2; and arsenopyrite (Apy-3) + graphite + Bi-bearing minerals (Bis-3) + Au-3. The abundant amount of gold (Au-1~Au-3) is associated with Bi-bearing minerals (Bis-1~Bis-3), which coexist as inclusions and fill in fractures in these minerals. The mineral assemblages of arsenopyrite, Bi-minerals, and gold exhibit a clear As-Bi-Au mineralogy in the ores, and the ternary diagram of the chemical compositions of the Bi-minerals shows that Bi-minerals all fall in reducing regions, indicating that Bi-minerals are precipitated under reducing conditions. The gold compositions demonstrate a positive correlation (R2 = 0.58) between Au and Bi. Consequently, we propose that the gold experienced the ore-forming fluids concentration and further Bi-melts scavenging for the Laozuoshan gold deposit mineralization. The Bi collector model is essential in interpreting the high-grade gold in the Laozuoshan gold deposit, indicating that the geochemical anomalies observed with bismuth may be a critical potential exploration target for the high-grade gold deposits in the Jiamusi Block.


  • Open Access

    Phase Formation and Microstructure Evolution of Al-5Si-0.8Mg Alloys with Different Mn Concentrations

    by Ni Tian, Guangdong Wang, Yiran Zhou, Chuncheng Liu, Kun Liu, Gang Zhao, Liang Zuo

    Mg-containing high-Si aluminum alloys are heat-treatable alloys that are widely used in industry. Substantial attention has been paid to increasing the performance of such alloys by adding a small amount of Mn, which is an effective and common alloying element in aluminum alloys. In the present work, the solidification process of Mn-free Al-5Si-0.8Mg alloy and Al-5Si-0.8Mg-(0.45–1.97)Mn alloys are analyzed by the experimental results combined with thermodynamic calculation. The results showed that α-Al, Si, Mg2Si and π (Al8Mg3FeSi6) are predominant phases in the Mn-free Al-5Si-0.8Mg alloy while the π (Al8Mg3FeSi6) phase are transformed to α-Al(FeMn)Si phase with the addition of 0.45% Mn. With increasing Mn addition to 0.72%, the L→α-Al was replaced by L→α-Al(FeMn)Si and a primary α-Al(FeMn)Si phase appeared. Further increasing the Mn to 1.97%, the solidification reactions remained unchanged. However, the size and number of the primary α-Al(FeMn)Si phase gradually increased, while the divorced eutectic phenomenon of quaternary eutectic structure gradually weakened. Meanwhile, the Mg2Si phase in the quaternary eutectic structure gradually transformed from blocky to fine eutectic lamellar, and the quaternary eutectic structure was significantly refined. Primary blocky α-Al(FeMn)Si began to form when the Mn content was higher than 0.75%.


  • Open Access

    Formation of Phases and Microstructures in Al-8Si Alloys with Different Mg Content

    by Ni Tian, Guangdong Wang, Yiran Zhou, Chuncheng Liu, Kun Liu, Gang Zhao, Liang Zuo

    Mg-containing high-silicon aluminum alloy is a heat-treatable aluminum alloy that is now widely used in the aerospace and automotive industries because of its high specific strength, high wear resistance and corrosion resistance, low thermal expansion coefficient, and low cost. More attention has been paid to optimizing the microstructure to increase the performance of this type of aluminum alloy. In the present work, the solidification processes of Mg-free and Mg-containing (0.33–1.32%) Al-8Si alloys were analyzed by the experimental results combined with the thermodynamic calculation. The results showed that α-Al, Si, and Al5FeSi were in the Mg-free Al-8Si alloy ingots, while the Al5FeSi phases in alloys with Mg additions were transformed into π phases (Al8Mg3FeSi6) by the reaction L+Al5FeSi→α-Al+Si+Al8Mg3FeSi6. There was a binary eutectic reaction of L→α-Al+Al5FeSi when the Mg content exceeded 0.51% and the Fe content was higher than 0.17%. With the increase of Mg content, the volume of Mg2Si was gradually increased while the divorced eutectic phenomenon of the quaternary eutectic structure (α-Al+Si+Mg2Si+Al8Mg3FeSi6) was weakened and the eutectic structure was significantly refined.


  • Open Access

    Study of the Portevin-Le Chatelier (PLC) Characteristics of a 5083 Aluminum Alloy Sheet in Two Heat Treatment States

    by Ni Tian, Guangdong Wang, Yiran Zhou, Kun Liu, Gang Zhao, Liang Zuo

    In the present work, the role of Mg atoms in the form of either Mg clusters or β phase on the moving dislocations in 5083 aluminum alloy sheet were investigated by comparing the plastic flow behavior and Portevin-Le Chatelier (PLC) character in annealed and quenched conditions. It is found that the tensile strength of quenched sheets at different strain rates is slightly higher than those under annealed condition while the yield strength at both conditions is similar. In annealed sheets, the yield plateau was clearly observed at all tested strain rates with a strain less than 0.012, and its width increased with the increasing strain rate. However, no yield plateau was observed in quenched sheets. On the other hand, the characters of PLC are greatly varied with applied conditions and strain rate. Generally, annealed sheets have a higher waiting time, but lower critical strain/stress at lower strain rate (~1 × 10−4 s−1), but they are similar at a higher strain rate (1 × 10−2 s−1). However, the falling time at both annealed and quenched conditions are almost the same at tested strain rates.