Peihong Cong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Peihong Cong has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Hiroshi Tani
Mechanical Engineering Department, Kansai University, Osaka, Japan
2 shared publications - Renguo Lu
Faculty of Engineering Science, Kansai University, Osaka 564-8680, Japan
2 shared publications - Shinji Koganezawa
Department of Mechanical Engineering, Kansai University, Suita, Japan
2 shared publications - Xujun Liu
State Key Laboratory of Molecular Engineering of Polymers, Fudan University, Shanghai 200433, China
2 shared publications - Chencheng Wu
Graduate School of Science and Engineering, Kansai University, Osaka 564-8680, Japan
1 shared publication Hai‐Qing Wang
Key Laboratory for Liquid–Solid Structural Evolution & Processing of Materials of Ministry of Education, Shandong University, Jinan 250001, China
1 shared publication
Latest Publications
- Open Access
- 9 April 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (4) , 173
Effect of Applied Current on Tribological Properties of Polyphenyl Ether
The widespread adoption of electric vehicles (EVs) has introduced new challenges in drivetrain lubrication, particularly concerning electrical corrosion, frictional wear, and hydrogen embrittlement. While polyalphaolefin (PAO)-based lubricants are commonly used, they struggle under high-speed and high-torque conditions. In contrast, polyphenyl ether (PPE)-based lubricants offer superior wear resistance and effectively suppress hydrogen generation, making them promising for EV applications. This study examines the effects of current direction and magnitude on tribofilm formation and frictional behavior in a PPE-lubricated environment. The results show that PPE exhibits unique tribofilm adhesion characteristics influenced by electrical conditions, unlike PAO. Surface analysis reveals that the tribofilm mainly consists of amorphous carbon, and friction under an electrical bias induces PPE oxidation, with oxidation products forming more readily at the positive electrode. Tribofilm formation correlated with increased friction and wear, particularly under currents of 10 mA or higher. Although PPE is more sensitive to electrical influences than PAO, it exhibits excellent wear resistance and maintains a low coefficient of friction even under electrification. This suggests that PPE could be suitable for lubrication in electrical environments and may serve as a promising lubricant for EV drive systems and similar applications.
- 9 April 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (4) , 173
Open AccessEffect of Applied Current on Tribological Properties of Polyphenyl Ether
The widespread adoption of electric vehicles (EVs) has introduced new challenges in drivetrain lubrication, particularly concerning electrical corrosion, frictional wear, and hydrogen embrittlement. While polyalphaolefin (PAO)-based lubricants are commonly used, they struggle under high-speed and high-torque conditions. In contrast, polyphenyl ether (PPE)-based lubricants offer superior wear resistance and effectively suppress hydrogen generation, making them promising for EV applications. This study examines the effects of current direction and magnitude on tribofilm formation and frictional behavior in a PPE-lubricated environment. The results show that PPE exhibits unique tribofilm adhesion characteristics influenced by electrical conditions, unlike PAO. Surface analysis reveals that the tribofilm mainly consists of amorphous carbon, and friction under an electrical bias induces PPE oxidation, with oxidation products forming more readily at the positive electrode. Tribofilm formation correlated with increased friction and wear, particularly under currents of 10 mA or higher. Although PPE is more sensitive to electrical influences than PAO, it exhibits excellent wear resistance and maintains a low coefficient of friction even under electrification. This suggests that PPE could be suitable for lubrication in electrical environments and may serve as a promising lubricant for EV drive systems and similar applications.
- Open Access
- 13 March 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (3) , 91
Tribofilm Formation and Friction Reduction Performance on Laser-Textured Surface with Micro-Grooved Structures
Tribofilms, resulting from tribochemical reactions involving lubricants, additives, and metal surfaces, are pivotal in reducing friction, preventing adhesion, and minimizing wear. This study investigates the tribological characteristics of textured surfaces in boundary lubrication, emphasizing the impact of surface texturing on tribofilm formation. Untextured surfaces manifest high friction coefficients and low wear owing to the development of thick tribofilms. However, debris accumulation impedes further tribochemical reactions, necessitating more energy for sliding and resulting in higher friction coefficients. Additionally, molybdenum dialkyl dithiocarbamate-derived MoS2 oxidation diminishes the expected lubrication effect. Textured surfaces exhibit lower friction coefficients and higher wear because the structure aids debris removal, promoting the formation of thinner tribofilms. Despite increased wear from solid-to-solid contact, textured surfaces facilitate an early fluid lubrication transition and enhance cavitation capacity, leading to reduced friction coefficients. We also consider the impact of sliding direction angles on friction coefficients, revealing that lower angles parallel to the grooves heighten friction, whereas higher angles enhance cavitation capacity. Unexpectedly, a 90° sliding direction angle increases the friction coefficients, attributed to MoS2 distribution in the tribofilms. These results provide crucial insights for optimizing lubrication strategies and enhancing wear resistance in boundary lubrication scenarios.
- 13 March 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (3) , 91
Open AccessTribofilm Formation and Friction Reduction Performance on Laser-Textured Surface with Micro-Grooved Structures
Tribofilms, resulting from tribochemical reactions involving lubricants, additives, and metal surfaces, are pivotal in reducing friction, preventing adhesion, and minimizing wear. This study investigates the tribological characteristics of textured surfaces in boundary lubrication, emphasizing the impact of surface texturing on tribofilm formation. Untextured surfaces manifest high friction coefficients and low wear owing to the development of thick tribofilms. However, debris accumulation impedes further tribochemical reactions, necessitating more energy for sliding and resulting in higher friction coefficients. Additionally, molybdenum dialkyl dithiocarbamate-derived MoS2 oxidation diminishes the expected lubrication effect. Textured surfaces exhibit lower friction coefficients and higher wear because the structure aids debris removal, promoting the formation of thinner tribofilms. Despite increased wear from solid-to-solid contact, textured surfaces facilitate an early fluid lubrication transition and enhance cavitation capacity, leading to reduced friction coefficients. We also consider the impact of sliding direction angles on friction coefficients, revealing that lower angles parallel to the grooves heighten friction, whereas higher angles enhance cavitation capacity. Unexpectedly, a 90° sliding direction angle increases the friction coefficients, attributed to MoS2 distribution in the tribofilms. These results provide crucial insights for optimizing lubrication strategies and enhancing wear resistance in boundary lubrication scenarios.
- 13 May 2012
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 126 (5) , 1746-1753
Effect of the matrix resin structure on the mechanical properties and braking performance of organic brake pads
Two chemically modified phenolic resins (PFs) designed and developed for the matrix resins of organic friction materials were characterized. The braking performance of organic brake pads based on the two modified resins and reinforced with hybrid fibers was investigated on a full‐scale test bench. The results indicate that the modified PF with more internal friction units possessed much higher impact and compression strengths, greater toughness, and better braking stability. We concluded that the matrix resin with more adjustable structural units allowed for an adjustable Young's modulus and dynamic mechanical properties and, hence, could indirectly allow an adjustable friction coefficient for organic brake pads during braking process and, furthermore, enable the optimization of braking stability of the friction couples. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2012
- 13 May 2012
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 126 (5) , 1746-1753
Effect of the matrix resin structure on the mechanical properties and braking performance of organic brake pads
Two chemically modified phenolic resins (PFs) designed and developed for the matrix resins of organic friction materials were characterized. The braking performance of organic brake pads based on the two modified resins and reinforced with hybrid fibers was investigated on a full‐scale test bench. The results indicate that the modified PF with more internal friction units possessed much higher impact and compression strengths, greater toughness, and better braking stability. We concluded that the matrix resin with more adjustable structural units allowed for an adjustable Young's modulus and dynamic mechanical properties and, hence, could indirectly allow an adjustable friction coefficient for organic brake pads during braking process and, furthermore, enable the optimization of braking stability of the friction couples. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2012
- 1 February 2007
- Published by Taylor & Francis in Journal of Macromolecular Science, Part B
- Vol. 46 (2) , 373-385
Tribological Properties of Polycarbonate Blended with High‐density Polyethylene and High‐density Polyethylene Grafted with Maleic Anhydride
High‐density polyethylene (HDPE) and maleic anhydride grafted HDPE (HDPE‐g‐MA) were selected as lubricant and compatibilizer, respectively, for improving the tribological and mechanical properties of polycarbonate (PC). The morphology of worn surfaces and debris was observed by means of scanning electron microscopy (SEM). The mated steel ring surface was analyzed by using SEM combined with energy dispersive spectroscopy (EDS). Both HDPE and HDPE‐g‐MA reduced the friction and wear of pure PC. HDPE‐g‐MA, which had a better compatibility with PC than HDPE, resulted in better improvement of the mechanical and tribological properties of the PC matrix. A 10 vol. % HDPE‐g‐MA reduced the wear of pure PC by 4 orders of magnitude, and the friction coefficient was reduced from 0.86 to 0.22. Such improvements in the tribological behavior resulted from the good self lubrication of HDPE and HDPE‐g‐MA. The PC/HDPE‐g‐MA (S90‐0‐10) polyblend also showed higher notched impact strength than pure PC. It may be a useful material for application in tribological fields.
- 1 February 2007
- Published by Taylor & Francis in Journal of Macromolecular Science, Part B
- Vol. 46 (2) , 373-385
Tribological Properties of Polycarbonate Blended with High‐density Polyethylene and High‐density Polyethylene Grafted with Maleic Anhydride
High‐density polyethylene (HDPE) and maleic anhydride grafted HDPE (HDPE‐g‐MA) were selected as lubricant and compatibilizer, respectively, for improving the tribological and mechanical properties of polycarbonate (PC). The morphology of worn surfaces and debris was observed by means of scanning electron microscopy (SEM). The mated steel ring surface was analyzed by using SEM combined with energy dispersive spectroscopy (EDS). Both HDPE and HDPE‐g‐MA reduced the friction and wear of pure PC. HDPE‐g‐MA, which had a better compatibility with PC than HDPE, resulted in better improvement of the mechanical and tribological properties of the PC matrix. A 10 vol. % HDPE‐g‐MA reduced the wear of pure PC by 4 orders of magnitude, and the friction coefficient was reduced from 0.86 to 0.22. Such improvements in the tribological behavior resulted from the good self lubrication of HDPE and HDPE‐g‐MA. The PC/HDPE‐g‐MA (S90‐0‐10) polyblend also showed higher notched impact strength than pure PC. It may be a useful material for application in tribological fields.