Mehrzad Alizadeh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mehrzad Alizadeh has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Shohji Tsushima
12 shared publications- Patcharawat Charoen-Amornkitt
Electrochemical Energy Storage and Conversion Laboratory, Department of Mechanical Engineering, Faculty of Engineering, King Mongkut’s University of Technology Thonburi, 126 Pracha Uthit Rd., Bang Mod, Thung Khru, Bangkok 10140, Thailand
10 shared publications - Takahiro Suzuki
Department of Mechanical Engineering, Graduate School of Engineering, Osaka University, Suita, Osaka, 565-0871, Japan
10 shared publications - Mengly Long4 shared publications
Takahiro Suzuki
4 shared publications- Jeff Gostick
Department of Chemical Engineering, University of Waterloo, ON, Canada
2 shared publications
Latest Publications
- 9 January 2026
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 259
Entropy generation analysis of topology-optimized porous reactors under pulsating flow conditions
- 9 January 2026
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 259
Entropy generation analysis of topology-optimized porous reactors under pulsating flow conditions
- Open Access
- 29 November 2024
- Published by IOP Publishing in Progress in Energy
- Vol. 7 (1) , 012003
Recent advances in electrode optimization of electrochemical energy devices using topology optimization
Topology optimization (TO) has emerged as a prominent trend in recent years, driven by its ability to explore optimized material distributions from scratch. Recently, there has been a significant shift in the application of TO, in optimizing systems involving complex electrochemical reactions, particularly electrode porous structures. This paper aims to examine the utilization of TO in enhancing electrodes across various electrochemical energy devices (EEDs). It encompasses a broad spectrum of applications, including the optimization of porous electrodes through the density-based method and interfaces between electrodes and electrolytes through the level-set method. The paper will delve into the challenges and opportunities associated with employing TO in electrode design for EEDs. These challenges involve addressing computational complexity, the absence of theoretical foundations for optimized structures, and the fabrication of complex structures for practical real-world applications. Additionally, beyond TO, the paper will spotlight other notable techniques in the structural design of porous electrodes using mathematical optimization. By offering insights into state-of-the-art research and developments in TO’s application to electrode design, this paper provides researchers with valuable resources to navigate the evolving landscape of electrode design for EEDs.
- 29 November 2024
- Published by IOP Publishing in Progress in Energy
- Vol. 7 (1) , 012003
Open AccessRecent advances in electrode optimization of electrochemical energy devices using topology optimization
Topology optimization (TO) has emerged as a prominent trend in recent years, driven by its ability to explore optimized material distributions from scratch. Recently, there has been a significant shift in the application of TO, in optimizing systems involving complex electrochemical reactions, particularly electrode porous structures. This paper aims to examine the utilization of TO in enhancing electrodes across various electrochemical energy devices (EEDs). It encompasses a broad spectrum of applications, including the optimization of porous electrodes through the density-based method and interfaces between electrodes and electrolytes through the level-set method. The paper will delve into the challenges and opportunities associated with employing TO in electrode design for EEDs. These challenges involve addressing computational complexity, the absence of theoretical foundations for optimized structures, and the fabrication of complex structures for practical real-world applications. Additionally, beyond TO, the paper will spotlight other notable techniques in the structural design of porous electrodes using mathematical optimization. By offering insights into state-of-the-art research and developments in TO’s application to electrode design, this paper provides researchers with valuable resources to navigate the evolving landscape of electrode design for EEDs.
- Open Access
- 1 November 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (11) , 114506
A Mathematically Optimized Design Solution for Structure of PEMFC Catalyst Layer Based on a Two-Phase Flow Model
Proton exchange membrane fuel cells (PEMFCs) have emerged as a promising solution as the world is moving toward sustainable energy resources. However, in order to compete economically with existing technologies, further improvements in performance are necessary. Mathematical modeling and optimization are viable tools for designing better PEMFCs. This study aims to provide a framework for topological optimization of the electrode structure, with the ultimate goal of enhancing cell performance. To achieve this, a two-phase flow model of PEMFC is developed to characterize the cell performance. The model is then coupled with a topology optimization technique, which is the main focus of the present work, to seek an optimized constituent distribution in the catalyst layer. Results indicate that an electrode with a heterogeneous structure can enhance the overall cell performance by balancing various transport and rate processes. The optimized designs are investigated for various key factors, including effective diffusivity, effective conductivity, and liquid water management, to demonstrate how an optimized design can be advantageous.
- 1 November 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (11) , 114506
Open AccessA Mathematically Optimized Design Solution for Structure of PEMFC Catalyst Layer Based on a Two-Phase Flow Model
Proton exchange membrane fuel cells (PEMFCs) have emerged as a promising solution as the world is moving toward sustainable energy resources. However, in order to compete economically with existing technologies, further improvements in performance are necessary. Mathematical modeling and optimization are viable tools for designing better PEMFCs. This study aims to provide a framework for topological optimization of the electrode structure, with the ultimate goal of enhancing cell performance. To achieve this, a two-phase flow model of PEMFC is developed to characterize the cell performance. The model is then coupled with a topology optimization technique, which is the main focus of the present work, to seek an optimized constituent distribution in the catalyst layer. Results indicate that an electrode with a heterogeneous structure can enhance the overall cell performance by balancing various transport and rate processes. The optimized designs are investigated for various key factors, including effective diffusivity, effective conductivity, and liquid water management, to demonstrate how an optimized design can be advantageous.
- Open Access
- 2 September 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (9) , 090534
Multiphysics Simulation of Multi-layered Fibrous Electrodes for the Vanadium Redox Flow Battery
Electrospinning can create customized flow-through electrodes for redox flow batteries with small fibers to enhance reactive surface area. A downside is higher pressure drop and parasitic pumping losses. Multilayered electrodes are a promising remedy, but it is not obvious what properties each layer should have to get the most benefit. In this work, a multiphysics simulation was used to explore the impact of varying the properties of each layer on the performance of a cell, including fiber size, fiber alignment, and porosity. The results showed that a 300% increase in limiting current can be obtained over commercial materials when the layer near the membrane has larger fibers with smaller fibers in each successive layer (1.8, 1.0 & 0.2 um, respectively). This arrangement had relatively lower overall efficiency once pumping power was taken into account. A compromise was obtained by placing a high porosity layer near the membrane with lower porosity in each successive layer (91%, 86%, and 81%, respectively). This case resulted in a 250% increase in limiting current, while expending only 0.1% of the output power on pumping.
- 2 September 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (9) , 090534
Open AccessMultiphysics Simulation of Multi-layered Fibrous Electrodes for the Vanadium Redox Flow Battery
Electrospinning can create customized flow-through electrodes for redox flow batteries with small fibers to enhance reactive surface area. A downside is higher pressure drop and parasitic pumping losses. Multilayered electrodes are a promising remedy, but it is not obvious what properties each layer should have to get the most benefit. In this work, a multiphysics simulation was used to explore the impact of varying the properties of each layer on the performance of a cell, including fiber size, fiber alignment, and porosity. The results showed that a 300% increase in limiting current can be obtained over commercial materials when the layer near the membrane has larger fibers with smaller fibers in each successive layer (1.8, 1.0 & 0.2 um, respectively). This arrangement had relatively lower overall efficiency once pumping power was taken into account. A compromise was obtained by placing a high porosity layer near the membrane with lower porosity in each successive layer (91%, 86%, and 81%, respectively). This case resulted in a 250% increase in limiting current, while expending only 0.1% of the output power on pumping.
- Open Access
- 1 July 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (7) , 074502
Numerical Modeling and Topology Optimization for Designing the Anode Catalyst Layer in Proton Exchange Membrane Water Electrolyzers Considering Mass Transport Limitation
With the escalation of global warming primarily attributed to fossil fuel and other non-renewable energy consumption, the production of green hydrogen emerges as a mitigation strategy to reduce fossil fuel usage and effectively harness renewable energy sources for energy storage. The proton exchange membrane water electrolyzer (PEMWE) stands out as a promising technology, boasting high efficiency and a rapid response to variations in current density. Despite its stellar performance, the reliance on precious materials presents a cost challenge. To address this concern, we developed a numerical model considering mass transport limitations and temperature variation. The topology optimization (TO) method is employed to generate the optimal structure of the electrode by organizing the two primary constituent materials. Additionally, the impact of optimization points representing low (1.73 V) and high (2.03 V) operating voltage characteristics is analyzed. The optimal structure demonstrates a maximum performance improvement of up to 2.7 times at an operating voltage of 2.03 V compared to the homogeneous electrode structure. The gas coverage model influences the rearrangement of constituent materials, particularly the void fraction, creating channels to facilitate the reaction. Optimization at high voltage points yields a more significant improvement compared to the low voltage scenario.
- 1 July 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (7) , 074502
Open AccessNumerical Modeling and Topology Optimization for Designing the Anode Catalyst Layer in Proton Exchange Membrane Water Electrolyzers Considering Mass Transport Limitation
With the escalation of global warming primarily attributed to fossil fuel and other non-renewable energy consumption, the production of green hydrogen emerges as a mitigation strategy to reduce fossil fuel usage and effectively harness renewable energy sources for energy storage. The proton exchange membrane water electrolyzer (PEMWE) stands out as a promising technology, boasting high efficiency and a rapid response to variations in current density. Despite its stellar performance, the reliance on precious materials presents a cost challenge. To address this concern, we developed a numerical model considering mass transport limitations and temperature variation. The topology optimization (TO) method is employed to generate the optimal structure of the electrode by organizing the two primary constituent materials. Additionally, the impact of optimization points representing low (1.73 V) and high (2.03 V) operating voltage characteristics is analyzed. The optimal structure demonstrates a maximum performance improvement of up to 2.7 times at an operating voltage of 2.03 V compared to the homogeneous electrode structure. The gas coverage model influences the rearrangement of constituent materials, particularly the void fraction, creating channels to facilitate the reaction. Optimization at high voltage points yields a more significant improvement compared to the low voltage scenario.
- Open Access
- 25 June 2024
- Published by Elsevier in Computers & Structures
- Vol. 301
Topological optimization for tailored designs of advection–diffusion-reaction porous reactors based on pore scale modeling and simulation: A PNM-NSGA framework
- 25 June 2024
- Published by Elsevier in Computers & Structures
- Vol. 301
Open AccessTopological optimization for tailored designs of advection–diffusion-reaction porous reactors based on pore scale modeling and simulation: A PNM-NSGA framework
- Open Access
- 21 March 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Topological optimization for tailored designs of advection-diffusion-reaction porous reactors based on pore scale modeling and simulation
Reactive transport within porous reactors is crucial to many diverse applications, and the efficacy of these reactors hinges on their microstructure. Mathematical modeling and optimization play a pivotal role in the exploration of efficient designs, enabling the generation of structures that may not be achievable through random realizations of packings. In this study, we propose a framework for high-resolution topological optimization of porous flow-through reactors based on pore-scale simulations using a non-dominated sorting genetic algorithm II. A pore network model for an advection-diffusion-reaction system is developed to simulate reactor performance. This model is integrated with a mathematical optimization algorithm, incorporating a background grid and Delaunay tessellation. The optimization framework generates enhanced porous structures, simultaneously maximizing conversion rates while minimizing pumping costs. Striking a balance between permeability and reactive surface area, the final designs yield a set of Pareto optimal solutions, encompassing diverse non-dominated designs with varying reaction rates and hydraulic requirements. The results demonstrate that optimal pore configurations lead to a 280% increase in conversion rates and a 6% reduction in pumping costs at one end, while on the opposite end of the Pareto front, a 15.2% increase in reaction rates and an 11.3% reduction in pumping costs are observed.
- 21 March 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessTopological optimization for tailored designs of advection-diffusion-reaction porous reactors based on pore scale modeling and simulation
Reactive transport within porous reactors is crucial to many diverse applications, and the efficacy of these reactors hinges on their microstructure. Mathematical modeling and optimization play a pivotal role in the exploration of efficient designs, enabling the generation of structures that may not be achievable through random realizations of packings. In this study, we propose a framework for high-resolution topological optimization of porous flow-through reactors based on pore-scale simulations using a non-dominated sorting genetic algorithm II. A pore network model for an advection-diffusion-reaction system is developed to simulate reactor performance. This model is integrated with a mathematical optimization algorithm, incorporating a background grid and Delaunay tessellation. The optimization framework generates enhanced porous structures, simultaneously maximizing conversion rates while minimizing pumping costs. Striking a balance between permeability and reactive surface area, the final designs yield a set of Pareto optimal solutions, encompassing diverse non-dominated designs with varying reaction rates and hydraulic requirements. The results demonstrate that optimal pore configurations lead to a 280% increase in conversion rates and a 6% reduction in pumping costs at one end, while on the opposite end of the Pareto front, a 15.2% increase in reaction rates and an 11.3% reduction in pumping costs are observed.