Jun Nishiyama
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jun Nishiyama has a total of 93 co-authors. Here are the top co-authors by number of shared publications:
- Toru Obara
Tokyo Institute of Technology
9 shared publications - Anton D. Smirnov
Institute of Nuclear Physics and Engineering, National Research Nuclear University MEPhI, Kashirskoe Shosse, 31, Moscow, Russian Federation, 115409
2 shared publications - Ekaterina V. Bogdanova
Department of theoretical and experimental physics of nuclear reactors, National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Kashirskoe shosse 31, Moscow, Russia
2 shared publications - Georgiy V. Tikhomirov
National Research Nuclear University “MEPhI” (NRNU MEPhI), Moscow, Russia
2 shared publications - Hiroki Takezawa
Tokyo City University, Department of Nuclear Safety Engineering, Faculty of Engineering, Tokyo, Japan
2 shared publications - I. S. Saldikov
National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Department of Theoretical and Experimental Physics of Nuclear Reactors, 31, Kashirskoye shosse, 115409, Moscow, Russia
2 shared publications
Latest Publications
- Open Access
- 20 May 2024
- Published by Taylor & Francis in Nuclear Science and Engineering
- Vol. 199 (2) , 266-279
Practical Design of a Breed-and-Burn Lead-Cooled Fast Reactor with Rotational Fuel Shuffling Strategy
- 20 May 2024
- Published by Taylor & Francis in Nuclear Science and Engineering
- Vol. 199 (2) , 266-279
Open AccessPractical Design of a Breed-and-Burn Lead-Cooled Fast Reactor with Rotational Fuel Shuffling Strategy
- Open Access
- 18 November 2022
- Published by Taylor & Francis in Nuclear Science and Engineering
- Vol. 197 (4) , 711-718
Core Concept of Small Rotational Fuel-Shuffling Breed-and-Burn Fast Reactor with Nitride Fuel and Sodium Coolant
The purpose of this study is to clarify the possibility of designing a small rotational fuel-shuffling breed-and-burn fast reactor (RFBB) with nitride fuel and sodium coolant based on neutronic and heat removal analyses. In these reactor analyses, uranium nitride fuel with a helium bond and sodium coolant was applied to the RFBB, whose thermal power is 450 MW. The structural and cladding materials are oxide dispersion-strengthened ferritic steel. Calculation results showed that the core with rotational fuel shuffling achieved an equilibrium state at criticality near unity, and the average discharge burnup of discharged fuel was 187 MWd/kg heavy metal. In this equilibrium state, reactor characteristics, such as neutron flux and the power profile, were almost stable, and the maximum displacements-per-atom value was slightly higher than 650. A steady-state heat removal analysis was performed for the hottest channel in the core, revealing that the fuel temperature was lower than the operational limit temperature and that the cladding temperature was lower than its melting temperature. However, it was slightly higher than the suggested value of 600°C for retaining nitride fuel integrity for high burnup. It was shown that the core radius could be smaller than that of the metal-fueled core of the previous study.
- 18 November 2022
- Published by Taylor & Francis in Nuclear Science and Engineering
- Vol. 197 (4) , 711-718
Open AccessCore Concept of Small Rotational Fuel-Shuffling Breed-and-Burn Fast Reactor with Nitride Fuel and Sodium Coolant
The purpose of this study is to clarify the possibility of designing a small rotational fuel-shuffling breed-and-burn fast reactor (RFBB) with nitride fuel and sodium coolant based on neutronic and heat removal analyses. In these reactor analyses, uranium nitride fuel with a helium bond and sodium coolant was applied to the RFBB, whose thermal power is 450 MW. The structural and cladding materials are oxide dispersion-strengthened ferritic steel. Calculation results showed that the core with rotational fuel shuffling achieved an equilibrium state at criticality near unity, and the average discharge burnup of discharged fuel was 187 MWd/kg heavy metal. In this equilibrium state, reactor characteristics, such as neutron flux and the power profile, were almost stable, and the maximum displacements-per-atom value was slightly higher than 650. A steady-state heat removal analysis was performed for the hottest channel in the core, revealing that the fuel temperature was lower than the operational limit temperature and that the cladding temperature was lower than its melting temperature. However, it was slightly higher than the suggested value of 600°C for retaining nitride fuel integrity for high burnup. It was shown that the core radius could be smaller than that of the metal-fueled core of the previous study.
- Open Access
- 18 October 2021
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 59 (4) , 438-445
Granular fuel debris shape modeling in MPS-DEM for the simulation of fuel debris bed formation in water
During the decommissioning of the Fukushima Daiichi Nuclear Power Station, it is vital to ensure that work stays safely under the subcriticality state in order to protect workers and the public from a criticality accident. To improve criticality evaluation accuracy, this study was performed to clarify whether the effect of fuel debris shape can be modeled by adjusting the friction coefficient in an MPS-DEM simulation of fuel debris behavior in water. The results showed it was possible to efficiently adjust the friction coefficients to model the shape effect in underwater conditions. Then, from the validation of the adjusted friction coefficients, we clarified that this method can be applied under conditions where the interaction between the fine grain fuel debris is dominant. On the other hand, further research is needed when this model is applied where water flow is dominant.
- 18 October 2021
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 59 (4) , 438-445
Open AccessGranular fuel debris shape modeling in MPS-DEM for the simulation of fuel debris bed formation in water
During the decommissioning of the Fukushima Daiichi Nuclear Power Station, it is vital to ensure that work stays safely under the subcriticality state in order to protect workers and the public from a criticality accident. To improve criticality evaluation accuracy, this study was performed to clarify whether the effect of fuel debris shape can be modeled by adjusting the friction coefficient in an MPS-DEM simulation of fuel debris behavior in water. The results showed it was possible to efficiently adjust the friction coefficients to model the shape effect in underwater conditions. Then, from the validation of the adjusted friction coefficients, we clarified that this method can be applied under conditions where the interaction between the fine grain fuel debris is dominant. On the other hand, further research is needed when this model is applied where water flow is dominant.
- Open Access
- 4 October 2021
- Published by Taylor & Francis in Nuclear Science and Engineering
- Vol. 196 (3) , 322-341
Neutron Balance Features in Breed-and-Burn Fast Reactors
Since nuclear power plants were first developed over 80 years ago, most have had thermal reactors with enriched uranium as the main fuel. As a result, huge amounts of depleted uranium must be stockpiled and stored. Fast reactors operating in breed-and-burn (B&B) conditions are one potential approach to reducing the need for storage facilities to hold spent nuclear fuel and maximize the effective use of uranium resources. Sustaining B&B operating conditions depends on the choice of core materials. Here, we perform neutron balance analyses to determine the best combination of fuel and coolant material. We identify the features of the reactor core needed to maintain B&B operating mode by the amount of neutron loss from the core and coolant heat removal capability. Finally, we demonstrate that a large or small sodium-cooled fast reactor core with metallic or enriched nitride fuel, respectively, can sustain the chain reaction and B&B operation mode.
- 4 October 2021
- Published by Taylor & Francis in Nuclear Science and Engineering
- Vol. 196 (3) , 322-341
Open AccessNeutron Balance Features in Breed-and-Burn Fast Reactors
Since nuclear power plants were first developed over 80 years ago, most have had thermal reactors with enriched uranium as the main fuel. As a result, huge amounts of depleted uranium must be stockpiled and stored. Fast reactors operating in breed-and-burn (B&B) conditions are one potential approach to reducing the need for storage facilities to hold spent nuclear fuel and maximize the effective use of uranium resources. Sustaining B&B operating conditions depends on the choice of core materials. Here, we perform neutron balance analyses to determine the best combination of fuel and coolant material. We identify the features of the reactor core needed to maintain B&B operating mode by the amount of neutron loss from the core and coolant heat removal capability. Finally, we demonstrate that a large or small sodium-cooled fast reactor core with metallic or enriched nitride fuel, respectively, can sustain the chain reaction and B&B operation mode.
- 24 August 2021
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 59 (2) , 230-239
Impact of neutron generation time on released energy in falling fuel debris at supercritical condition
The risk of criticality accidents by fuel debris in the decommissioning of Fukushima Dai-ichi Nuclear Power Station is unlikely to be negligible. Therefore, an estimation of the consequences of such accidents is important. According to the latest study, estimating the energy that would be released if fuel debris became supercritical while falling into water is thought to be important. In falling fuel debris systems, the geometry changes substantially with time, which could cause large changes in neutron generation time. Treating the change in neutron generation time in a kinetics analysis might have a large impact on results such as released energy. Clarifying such phenomena could contribute to conducting a reasonable analysis and avoiding misleading results. Thus, in this study we seek to clarify whether it is necessary to consider changes of neutron generation time when evaluating released energy in a falling fuel debris system at supercritical conditions in water with a kinetics analysis based on a point reactor kinetics model. We found that change of neutron generation time should be considered when evaluating released energy in falling fuel debris systems at supercritical conditions; otherwise, obtained results could be unrealistic.
- 24 August 2021
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 59 (2) , 230-239
Impact of neutron generation time on released energy in falling fuel debris at supercritical condition
The risk of criticality accidents by fuel debris in the decommissioning of Fukushima Dai-ichi Nuclear Power Station is unlikely to be negligible. Therefore, an estimation of the consequences of such accidents is important. According to the latest study, estimating the energy that would be released if fuel debris became supercritical while falling into water is thought to be important. In falling fuel debris systems, the geometry changes substantially with time, which could cause large changes in neutron generation time. Treating the change in neutron generation time in a kinetics analysis might have a large impact on results such as released energy. Clarifying such phenomena could contribute to conducting a reasonable analysis and avoiding misleading results. Thus, in this study we seek to clarify whether it is necessary to consider changes of neutron generation time when evaluating released energy in a falling fuel debris system at supercritical conditions in water with a kinetics analysis based on a point reactor kinetics model. We found that change of neutron generation time should be considered when evaluating released energy in falling fuel debris systems at supercritical conditions; otherwise, obtained results could be unrealistic.
- 17 August 2021
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 59 (1) , 34-43
Monte Carlo codes benchmarking on sub-critical fuel debris particles system for neutronic analysis
Fuel debris removal is the most challenging part of damaged nuclear power station decommissioning. It is important to carry out nuclear safety calculations accurately and quickly enough. Here, it was clarified that modern codes based on the Monte Carlo method were capable of performing neutronic analysis with the same accuracy and without significant differences in the results. The benchmark calculations were performed using three codes: MVP, Serpent, and MCU. In this study, the comparison focused on multiplication factor, neutron fluxes and reaction rates relative difference, and calculation time of many fuel debris particles system. Then the calculation results were used when codes comparing. It was shown that the calculation results showed good agreement between all codes. It was assumed that minor differences in the thermal range of neutron fluxes can be caused by different thermal neutrons scattering treatment for all codes. The study also showed that solving such problems requires significant computing power and time. It has been proven that the statistical geometry model in the MVP and the explicit stochastic geometry model in the Serpent have the possibility to provide solutions with the same accuracy, but much faster.
- 17 August 2021
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 59 (1) , 34-43
Monte Carlo codes benchmarking on sub-critical fuel debris particles system for neutronic analysis
Fuel debris removal is the most challenging part of damaged nuclear power station decommissioning. It is important to carry out nuclear safety calculations accurately and quickly enough. Here, it was clarified that modern codes based on the Monte Carlo method were capable of performing neutronic analysis with the same accuracy and without significant differences in the results. The benchmark calculations were performed using three codes: MVP, Serpent, and MCU. In this study, the comparison focused on multiplication factor, neutron fluxes and reaction rates relative difference, and calculation time of many fuel debris particles system. Then the calculation results were used when codes comparing. It was shown that the calculation results showed good agreement between all codes. It was assumed that minor differences in the thermal range of neutron fluxes can be caused by different thermal neutrons scattering treatment for all codes. The study also showed that solving such problems requires significant computing power and time. It has been proven that the statistical geometry model in the MVP and the explicit stochastic geometry model in the Serpent have the possibility to provide solutions with the same accuracy, but much faster.
- Open Access
- 29 July 2021
- Published by Taylor & Francis in Nuclear Science and Engineering
- Vol. 196 (1) , 109-120
Feasibility of Sodium-Cooled Breed-and-Burn Reactor with Rotational Fuel Shuffling
The objective of the present study is to show that it is feasible to establish the breed-and-burn (B&B) mode of operation with rotational fuel shuffling in the S-PRISM core based on neutronic and thermal-hydraulic analyses. The results quantified the impact of major core design choices on the criticality of a core that uses sodium as a coolant material and HT9 steel as structural material. The design variables examined include the binary metallic fuel U-Zr with different weight percentages of zirconium as well as different core heights and fuel rod pitch-to-diameter ratios (P/Ds) in the fuel assembly. We found that a core using the binary metallic fuel U-Zr with 2 wt% zirconium, with a core height of 200 cm, a P/D of 1.086, and a core power of 400 MW(thermal), could overcome some major design constraints. It was also found that with shuffling intervals of 1125 to 1250 days, the core with rotational fuel shuffling was critical in the equilibrium state, and the possible average discharged burnup was from 274.8 to 305.3 GWd/ton HM. Reactor characteristics such as neutron flux and power profile were almost stable during the equilibrium cycle. A steady-state thermal-hydraulic analysis was performed for the hottest channel in the core. It revealed that both the fuel and cladding maximum temperatures were less than the melting point of the fuel and the chemical interaction temperature of the HT-9, respectively. The mixed coolant outlet temperature was somewhat below the temperature usually observed in sodium-cooled fast reactors. Thus, it appears that the S-PRISM can be principally designed to have a B&B core.
- 29 July 2021
- Published by Taylor & Francis in Nuclear Science and Engineering
- Vol. 196 (1) , 109-120
Open AccessFeasibility of Sodium-Cooled Breed-and-Burn Reactor with Rotational Fuel Shuffling
The objective of the present study is to show that it is feasible to establish the breed-and-burn (B&B) mode of operation with rotational fuel shuffling in the S-PRISM core based on neutronic and thermal-hydraulic analyses. The results quantified the impact of major core design choices on the criticality of a core that uses sodium as a coolant material and HT9 steel as structural material. The design variables examined include the binary metallic fuel U-Zr with different weight percentages of zirconium as well as different core heights and fuel rod pitch-to-diameter ratios (P/Ds) in the fuel assembly. We found that a core using the binary metallic fuel U-Zr with 2 wt% zirconium, with a core height of 200 cm, a P/D of 1.086, and a core power of 400 MW(thermal), could overcome some major design constraints. It was also found that with shuffling intervals of 1125 to 1250 days, the core with rotational fuel shuffling was critical in the equilibrium state, and the possible average discharged burnup was from 274.8 to 305.3 GWd/ton HM. Reactor characteristics such as neutron flux and power profile were almost stable during the equilibrium cycle. A steady-state thermal-hydraulic analysis was performed for the hottest channel in the core. It revealed that both the fuel and cladding maximum temperatures were less than the melting point of the fuel and the chemical interaction temperature of the HT-9, respectively. The mixed coolant outlet temperature was somewhat below the temperature usually observed in sodium-cooled fast reactors. Thus, it appears that the S-PRISM can be principally designed to have a B&B core.
- 1 April 2021
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 153, 108040
Optimization of reactor size in the small sodium-cooled CANDLE burning reactor
- 1 April 2021
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 153, 108040
Optimization of reactor size in the small sodium-cooled CANDLE burning reactor
- Open Access
- 21 November 2019
- Published by Springer Nature in Respiratory Research
- Vol. 20 (1) , 1-16
Analysis of key clinical features for achieving complete remission in stage III and IV non-small cell lung cancer patients
Background: Although development of immune checkpoint inhibitors and various molecular target agents has extended overall survival time (OS) in advanced non-small cell lung cancer (NSCLC), a complete cure remains rare. We aimed to identify features and treatment modalities of complete remission (CR) cases in stages III and IV NSCLC by analyzing long-term survivors whose OS exceeded 3 years.Methods: From our hospital database, 1,699 patients, registered as lung cancer between 1stMar 2004 and 30thApr 2011, were retrospectively examined. Stage III or IV histologically or cytologically confirmed NSCLC patients with chemotherapy initiated during this period were enrolled. A Cox proportion hazards regression model was used. Data collection was closed on 13thFeb 2017.Results: There were 164 stage III and 279 stage IV patients, including 37 (22.6%) and 51 (18.3%) long-term survivors and 12 (7.3%) and 5 (1.8%) CR patients, respectively. The long-term survivors were divided into three groups: 3 ≤ OS < 5 years, 5 years ≤ OS with tumor, and 5 years ≤ OS without tumor (CR). The median OS of these groups were 1,405, 2,238, and 2,876 days in stage III and 1,368, 2,503, and 2,643 days in stage IV, respectively. The mean chemotherapy cycle numbers were 16, 20, and 10 in stage III and 24, 25, and 5 in stage IV, respectively. In the stage III CR group, all patients received chemoradiation, all oligometastases were controlled by radiation, and none had brain metastases. Compared with non-CR patients, the stage IV CR patients had smaller primary tumors and fewer metastases, which were independent prognostic factors for OS among long-term survivors. The 80% stage IV CR patients received radiation or surgery for controlling primary tumors, and the surgery rate for oligometastases was high. Pathological findings in the stage IV CR patients revealed that numerous inflammatory cells existed around and inside resected lung and brain tumors, indicating strong immune response.Conclusions: Multiple line chemotherapies with primary and oligometastatic controls by surgery and/or radiation might achieve cure in certain advanced NSCLC. Cure strategies must be changed according to stage III or IV.This study was retrospectively registered on 16thJun 2019 in UMIN Clinical Trials Registry (number UMIN000037078).
- 21 November 2019
- Published by Springer Nature in Respiratory Research
- Vol. 20 (1) , 1-16
Open AccessAnalysis of key clinical features for achieving complete remission in stage III and IV non-small cell lung cancer patients
Background: Although development of immune checkpoint inhibitors and various molecular target agents has extended overall survival time (OS) in advanced non-small cell lung cancer (NSCLC), a complete cure remains rare. We aimed to identify features and treatment modalities of complete remission (CR) cases in stages III and IV NSCLC by analyzing long-term survivors whose OS exceeded 3 years.Methods: From our hospital database, 1,699 patients, registered as lung cancer between 1stMar 2004 and 30thApr 2011, were retrospectively examined. Stage III or IV histologically or cytologically confirmed NSCLC patients with chemotherapy initiated during this period were enrolled. A Cox proportion hazards regression model was used. Data collection was closed on 13thFeb 2017.Results: There were 164 stage III and 279 stage IV patients, including 37 (22.6%) and 51 (18.3%) long-term survivors and 12 (7.3%) and 5 (1.8%) CR patients, respectively. The long-term survivors were divided into three groups: 3 ≤ OS < 5 years, 5 years ≤ OS with tumor, and 5 years ≤ OS without tumor (CR). The median OS of these groups were 1,405, 2,238, and 2,876 days in stage III and 1,368, 2,503, and 2,643 days in stage IV, respectively. The mean chemotherapy cycle numbers were 16, 20, and 10 in stage III and 24, 25, and 5 in stage IV, respectively. In the stage III CR group, all patients received chemoradiation, all oligometastases were controlled by radiation, and none had brain metastases. Compared with non-CR patients, the stage IV CR patients had smaller primary tumors and fewer metastases, which were independent prognostic factors for OS among long-term survivors. The 80% stage IV CR patients received radiation or surgery for controlling primary tumors, and the surgery rate for oligometastases was high. Pathological findings in the stage IV CR patients revealed that numerous inflammatory cells existed around and inside resected lung and brain tumors, indicating strong immune response.Conclusions: Multiple line chemotherapies with primary and oligometastatic controls by surgery and/or radiation might achieve cure in certain advanced NSCLC. Cure strategies must be changed according to stage III or IV.This study was retrospectively registered on 16thJun 2019 in UMIN Clinical Trials Registry (number UMIN000037078).