Xiaohui Qian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Xiaohui Qian has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Xiao-Yan Ma
Institute of High Energy Physics
5 shared publications - Jianxia Xiao
Jiangsu Domchamp New Material Technology Co., Ltd, Taixing City, China
3 shared publications - Shaojing Hou
Institute of High Energy Physics, Chinese Academy of Science, Beijing, China
3 shared publications - Wei He
Institute of High Energy Physics, Chinese Academy of Science, Beijing, China
3 shared publications - Xiaoyu Yang
Institute of High Energy Physics, Chinese Academy of Sciences, Beijing, China
3 shared publications - Yatian Pei
Institute of High Energy Physics, Chinese Academy of Science, Beijing, China
3 shared publications
Latest Publications
- 4 September 2026
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics A
Study of cluster counting method for CEPC drift chamber
Flavor physics and jet research at the Circular Electron and Positron Collider (CEPC) impose increasingly stringent requirements on particle identification (PID). As an alternative central tracker for the CEPC reference detector, one of the key optimization objectives of the drift chamber is its PID capability. The dN/dx method offers superior PID performance for the drift chamber by counting primary ionization. A prototype system including a 120-channel drift chamber, high-bandwidth readout electronics and DAQ software was developed and tested with cosmic rays. Preliminary results show a high signal-to-noise ratio (SNR) of 108.87 and an average rise time of 2.08[Formula: see text]ns, thereby demonstrating the low-noise and high-bandwidth performance of the electronics. Calibration and preliminary reconstruction have been completed, which lays a foundation for subsequent studies on dN/dx resolution.
- 4 September 2026
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics A
Study of cluster counting method for CEPC drift chamber
Flavor physics and jet research at the Circular Electron and Positron Collider (CEPC) impose increasingly stringent requirements on particle identification (PID). As an alternative central tracker for the CEPC reference detector, one of the key optimization objectives of the drift chamber is its PID capability. The dN/dx method offers superior PID performance for the drift chamber by counting primary ionization. A prototype system including a 120-channel drift chamber, high-bandwidth readout electronics and DAQ software was developed and tested with cosmic rays. Preliminary results show a high signal-to-noise ratio (SNR) of 108.87 and an average rise time of 2.08[Formula: see text]ns, thereby demonstrating the low-noise and high-bandwidth performance of the electronics. Calibration and preliminary reconstruction have been completed, which lays a foundation for subsequent studies on dN/dx resolution.
- Open Access
- 1 June 2023
- Published by IOP Publishing in Materials Research Express
- Vol. 10 (6) , 065303
Design and experiment of high load-bearing acrylic connection node for the world's largest acrylic spherical vessel
Acrylic is a kind of polymer material and is gradually applied to load-bearing components. The working stress and ultimate bearing capacity of the acrylic structure are the main design indexes. Aiming at the world’s largest acrylic spherical vessel, the structural design, finite element analysis and full-size prototype tensile test of a new acrylic connection node were carried out in this paper. This acrylic node will bear 90 kN tension force for 20 years. According to the viscoelastic characteristics of the material and the working environment, the stress of acrylic should be controlled below 3.5 MPa for long term used. At the time, the ultimate bearing capacity should be greater than 6 times the working load. According to the stress-strain curve of acrylic, its tensile strength is about 75 MPa. There is no obvious plastic deformation after fracture, showing the material characteristics of brittle fracture. According to the failure analysis of previous acrylic node structures and the characteristics of acrylic, the new acrylic node structure is proposed in this paper. Its performance is improved by reducing the cutting amount of acrylic nodes, optimizing the structure of embedded part and avoiding sharp corners. A 1/4 symmetrical acrylic node model is established FEA software, and the nonlinear problems such as material nonlinearity and friction contact are solved by finite element method. The FEA results show that the maximum principal stress of the node is about 2.92 MPa. The relative error between the FEA results and the experimental results is 7.24%, indicating that the FEA results are credible. The ultimate tensile load of the node can reach 1000 kN, which is about 11 times the working load. The failure of the node occurs at a sharp corner of the groove, instead of the maximum stress point. Therefore, stress concentration caused by sharp corners should be avoided in the design of acrylic structure.
- 1 June 2023
- Published by IOP Publishing in Materials Research Express
- Vol. 10 (6) , 065303
Open AccessDesign and experiment of high load-bearing acrylic connection node for the world's largest acrylic spherical vessel
Acrylic is a kind of polymer material and is gradually applied to load-bearing components. The working stress and ultimate bearing capacity of the acrylic structure are the main design indexes. Aiming at the world’s largest acrylic spherical vessel, the structural design, finite element analysis and full-size prototype tensile test of a new acrylic connection node were carried out in this paper. This acrylic node will bear 90 kN tension force for 20 years. According to the viscoelastic characteristics of the material and the working environment, the stress of acrylic should be controlled below 3.5 MPa for long term used. At the time, the ultimate bearing capacity should be greater than 6 times the working load. According to the stress-strain curve of acrylic, its tensile strength is about 75 MPa. There is no obvious plastic deformation after fracture, showing the material characteristics of brittle fracture. According to the failure analysis of previous acrylic node structures and the characteristics of acrylic, the new acrylic node structure is proposed in this paper. Its performance is improved by reducing the cutting amount of acrylic nodes, optimizing the structure of embedded part and avoiding sharp corners. A 1/4 symmetrical acrylic node model is established FEA software, and the nonlinear problems such as material nonlinearity and friction contact are solved by finite element method. The FEA results show that the maximum principal stress of the node is about 2.92 MPa. The relative error between the FEA results and the experimental results is 7.24%, indicating that the FEA results are credible. The ultimate tensile load of the node can reach 1000 kN, which is about 11 times the working load. The failure of the node occurs at a sharp corner of the groove, instead of the maximum stress point. Therefore, stress concentration caused by sharp corners should be avoided in the design of acrylic structure.
- 11 March 2022
- Published by Springer Nature in Radiation Detection Technology and Methods
- Vol. 6 (1) , 122-128
Research on thermoforming process of JUNO large acrylic spherical panel
- 11 March 2022
- Published by Springer Nature in Radiation Detection Technology and Methods
- Vol. 6 (1) , 122-128
Research on thermoforming process of JUNO large acrylic spherical panel
- Open Access
- 1 September 2021
- Published by IOP Publishing in Materials Research Express
- Vol. 8 (9) , 095305
Application of non-contact strain measurement based on CCD camera in PMMA material constitutive model
The Jiangmen Underground Neutrino Observation (JUNO) will build a polymethyl methacrylate (PMMA) spherical vessel of a diameter of 35.4 meters. The constitutive model of PMMA is a key parameter for the design of PMMA structure. The bulk polymerization bonding area is often the weak point of the PMMA structure, so it is useful to understand the constitutive model of bonding areas for FEA. However, the traditional contact strain measurement methods, such as the strain extensometer and resistance strain gauge, will have an impact on the strain of PMMA, as the lossy measurement. Traditional measuring methods also can’t measure the small-sized bonding areas as 3 mm in most structures. The non-contact strain measurement method based on the CCD camera is studied. The tensile test result shows that the influence of environment on the strain value is less than 0.01%. The two strain measurement methods, the CCD camera and strain extensometer, are compared. The strain curves obtained by the two methods are highly consistent, and the maximum strain difference is 8.53 e-4. The fracture strain of the PMMA tensile specimen is 4.32% and slight plastic deformation has occurred. The Zhu-Wang-Tang (ZWT) nonlinear viscoelastic constitutive model of PMMA is obtained by fitting the stress-strain data. The tensile test result of PMMA specimen with bulk polymerization bonding area shows that the constitutive equations are different when the length ratio of the bonding area is different. By analyzing the relationship between the length ratio and the coefficients of constitutive equation, the constitutive equation of the bonding area is finally obtained. The results show that the coefficient E 0 of the constitutive equation of the bonding area is smaller than that of the mother material. The fracture strain of PMMA specimen with bonding area is 2.60%, lower than that of mother material, which makes the coefficient β of the bonding area constitutive equation opposite to the sign of the mother material. The tensile strength of specimen with bonding area is about 85.68% of that of the mother material. The lower tensile strength makes the bonding area become one of the weak points of the structure.
- 1 September 2021
- Published by IOP Publishing in Materials Research Express
- Vol. 8 (9) , 095305
Open AccessApplication of non-contact strain measurement based on CCD camera in PMMA material constitutive model
The Jiangmen Underground Neutrino Observation (JUNO) will build a polymethyl methacrylate (PMMA) spherical vessel of a diameter of 35.4 meters. The constitutive model of PMMA is a key parameter for the design of PMMA structure. The bulk polymerization bonding area is often the weak point of the PMMA structure, so it is useful to understand the constitutive model of bonding areas for FEA. However, the traditional contact strain measurement methods, such as the strain extensometer and resistance strain gauge, will have an impact on the strain of PMMA, as the lossy measurement. Traditional measuring methods also can’t measure the small-sized bonding areas as 3 mm in most structures. The non-contact strain measurement method based on the CCD camera is studied. The tensile test result shows that the influence of environment on the strain value is less than 0.01%. The two strain measurement methods, the CCD camera and strain extensometer, are compared. The strain curves obtained by the two methods are highly consistent, and the maximum strain difference is 8.53 e-4. The fracture strain of the PMMA tensile specimen is 4.32% and slight plastic deformation has occurred. The Zhu-Wang-Tang (ZWT) nonlinear viscoelastic constitutive model of PMMA is obtained by fitting the stress-strain data. The tensile test result of PMMA specimen with bulk polymerization bonding area shows that the constitutive equations are different when the length ratio of the bonding area is different. By analyzing the relationship between the length ratio and the coefficients of constitutive equation, the constitutive equation of the bonding area is finally obtained. The results show that the coefficient E 0 of the constitutive equation of the bonding area is smaller than that of the mother material. The fracture strain of PMMA specimen with bonding area is 2.60%, lower than that of mother material, which makes the coefficient β of the bonding area constitutive equation opposite to the sign of the mother material. The tensile strength of specimen with bonding area is about 85.68% of that of the mother material. The lower tensile strength makes the bonding area become one of the weak points of the structure.
- Open Access
- 18 January 2021
- Published by Springer Nature in Research Square
Structural Design and Tensile Experiment of Connection Node between acrylic and Stainless Steel
Acrylic are widely used as load-bearing structural parts. In this study, the structural design, finite element analysis (FEA) and tensile experiment of the connection node of the acrylic spherical vessel designed for Jiangmen Underground Neutrino Observation (JUNO) are carried out. The acrylic connection node needs to withstand a tensile load of 90 kN for 20 years, and its ultimate bearing capacity is required to be 6 times the working load. Under working load, the stress of the acrylic structure should be less than 3.5 MPa. In the study, a connection node connecting acrylic and stainless steel is designed. By embedding the steel ring in the acrylic structure to connect with the support rod, the acrylic connection node can withstand high loads. A 1/4 symmetric model of connection node is established, and the FEA method is used to solve nonlinear problems such as material nonlinearity and frictional contact. The results of FEA show that the maximum principle stress of the connection node is about 2.92 MPa. By comparing the stress of the FEA results with the experimental results, the relative difference is 7.24 %, indicating that the FEA results are credible. The experiment results also show that the ultimate tensile load of the connection node can reach 1000 kN, which is about 11 times the working load. The breakdown of the connection node occurs at the sharp corner of the groove instead of the maximum stress point. Through the design, simulation and experiment of the connection node, for the brittle materials such as acrylic, the structure should avoid the defects such as sharp corner.
- 18 January 2021
- Published by Springer Nature in Research Square
Open AccessStructural Design and Tensile Experiment of Connection Node between acrylic and Stainless Steel
Acrylic are widely used as load-bearing structural parts. In this study, the structural design, finite element analysis (FEA) and tensile experiment of the connection node of the acrylic spherical vessel designed for Jiangmen Underground Neutrino Observation (JUNO) are carried out. The acrylic connection node needs to withstand a tensile load of 90 kN for 20 years, and its ultimate bearing capacity is required to be 6 times the working load. Under working load, the stress of the acrylic structure should be less than 3.5 MPa. In the study, a connection node connecting acrylic and stainless steel is designed. By embedding the steel ring in the acrylic structure to connect with the support rod, the acrylic connection node can withstand high loads. A 1/4 symmetric model of connection node is established, and the FEA method is used to solve nonlinear problems such as material nonlinearity and frictional contact. The results of FEA show that the maximum principle stress of the connection node is about 2.92 MPa. By comparing the stress of the FEA results with the experimental results, the relative difference is 7.24 %, indicating that the FEA results are credible. The experiment results also show that the ultimate tensile load of the connection node can reach 1000 kN, which is about 11 times the working load. The breakdown of the connection node occurs at the sharp corner of the groove instead of the maximum stress point. Through the design, simulation and experiment of the connection node, for the brittle materials such as acrylic, the structure should avoid the defects such as sharp corner.
- 11 August 2020
- Published by Springer Nature in Radiation Detection Technology and Methods
- Vol. 4 (3) , 345-355
Structure design and compression experiment of the supporting node for JUNO PMMA detector
- 11 August 2020
- Published by Springer Nature in Radiation Detection Technology and Methods
- Vol. 4 (3) , 345-355
Structure design and compression experiment of the supporting node for JUNO PMMA detector
- Open Access
- 1 March 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 774 (1)
FE Analysis on the Thermoforming Behaviour of Large Spherical PMMA Panelapplied in JUNO
Jiangmen Underground Neutrino Observation (JUNO) mainly focuses on determining neutrino mass hierarchy. The central detector is one of the keys to JUNO experiment, which is a spherical liquid scintillator detector with 20 kton target mass. The target vessel of the central detector is a huge acrylic vessel with a diameter of 35.4 m. Its construction will certainly face many enormous challenges and difficulties. This paper introduces the thermoforming process for huge acrylic spherical panel, which is a very important step in panel production. The effect of temperature on panel’s curvature during thermoforming is discussed. The temperature field and thermal deformation of the panel during thermoforming are analysed by finite element method. The temperature field affects the panel’s shape and cause its radius smaller than the thermoforming mold’s. The paper presents some suggestions on improving the shape of spherical panel. The temperature at concave and convex surfaces of panel should be controlled as equal as possible during thermoforming. The other method to get a spherical panel with design radius is increasing the forming mold’s radius appropriately.
- 1 March 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 774 (1)
Open AccessFE Analysis on the Thermoforming Behaviour of Large Spherical PMMA Panelapplied in JUNO
Jiangmen Underground Neutrino Observation (JUNO) mainly focuses on determining neutrino mass hierarchy. The central detector is one of the keys to JUNO experiment, which is a spherical liquid scintillator detector with 20 kton target mass. The target vessel of the central detector is a huge acrylic vessel with a diameter of 35.4 m. Its construction will certainly face many enormous challenges and difficulties. This paper introduces the thermoforming process for huge acrylic spherical panel, which is a very important step in panel production. The effect of temperature on panel’s curvature during thermoforming is discussed. The temperature field and thermal deformation of the panel during thermoforming are analysed by finite element method. The temperature field affects the panel’s shape and cause its radius smaller than the thermoforming mold’s. The paper presents some suggestions on improving the shape of spherical panel. The temperature at concave and convex surfaces of panel should be controlled as equal as possible during thermoforming. The other method to get a spherical panel with design radius is increasing the forming mold’s radius appropriately.
- 1 January 2019
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 55 (12) , 91-98
Analysis of Glass Shell's Thermal Stress Based on Orthogonal Experiment
- 1 January 2019
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 55 (12) , 91-98
Analysis of Glass Shell's Thermal Stress Based on Orthogonal Experiment