OGOleksandr Grebenikov

Oleksandr Grebenikov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Oleksandr Grebenikov has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Особливості технології виробництва закрилків крила літаків транспортної категорії

    by Олександр Григорович Гребеніков, Віталій Євгенович Василевський

    This work analyses and summarises the technological features of assembling flaps on transport aircraft, as well as identifying the main areas for improvement in assembly processes. An analysis of the design features of transport aircraft flaps, the formation of technological requirements for their assembly, a review of a typical technological assembly process, and an assessment of the problems and prospects for the development of this branch of aviation production are carried out. Strict re­quirements for accuracy are imposed on the design and assembly of flaps, which are regulated by design documentation and industry standards. These requirements can only be met by using a well-thought-out assembly scheme, precise equipment and a developed quality control system at all stages of the technological process. The paper considers the technology of flap assembly, taking into account design, technological and organisational factors. An analysis of the design and features of transport category flaps has been carried out. One of these features is the high sensitivity of their aerodynamic characteristics to deviations in geometric shape. In this regard, strict re­quirements for accuracy are imposed on the design and assembly of flaps, which are regulated by design documentation and industry standards. These requirements can only be met by using a well-thought-out assembly scheme, precise equipment and a developed quality control system at all stages of the technological process. Techno­logical requirements provide for strict control of connection parameters: diameter and shape of holes, fastening installation force, absence of gaps and defects. When using adhesives and sealants, the conditions for performing operations are additionally regu­lated: ambient temperature and humidity, surface preparation, holding time and methods of quality control of joints. The technological requirements for the assembly of transport category aircraft flaps are a set of interrelated conditions and restrictions aimed at ensuring high precision, strength, reliability and reproducibility of the design. The article discusses the preparation for the production of transport category aircraft flaps, which is one of the key stages in the product life cycle and largely determines the quality, labour intensity and economic efficiency of subsequent assembly proces­ses. The system for controlling and ensuring the quality of the assembly of transport category aircraft flaps is considered, which is a multi-level system aimed at preventing defects and ensuring high precision and reliability of the structure. An important direction in the development of flap assembly technology is the introduction of digital technologies, including the use of three-dimensional models, digital twins and virtual assembly process testing systems.

  • Метод визначення характеристик загального напружено-деформованого стану хвостової балки вертольота транспортної категорії

    by Олександр Григорович Гребеніков, Михайло Миколайович Орловський, Володимир Миколайович Костанді

    A method for determining the characteristics of the general stress-strain state of a helicopter tail boom, taking into account cutouts and reinforcing plates, has been developed, which includes the creation of a three-dimensional parametric finite element model, the design of the tail boom is presented, a calculation scheme for the tail boom of a transport category helicopter has been developed, and a finite element model.In the practice of world helicopter construction, single-rotor helicopters are most widely used, which are characterized by relative simplicity of design, convenient control and relatively low cost. The tail beam is the most complex part in the production of a helicopter. For a single-rotor helicopter, the tail beam is a very critical part of the structure, the destruction of which in most cases leads to an aviation accident. Ensuring the requirements for strength is an extremely responsible task, therefore it is regulated by the airworthiness standards mandatory for designers, which are an integral part of the Aviation Rules. These standards set the initial requirements for the calculation and experimental work to ensure strength, determine the loading conditions, and give instructions for determining the magnitude of the loads. In the practice of helicopter construction, the experience accumulated in aircraft construction in forming structural and power schemes of frame units is used.One of the main tasks of modern aviation science is the creation of a rational structural and power scheme of helicopter units, which makes it possible to achieve high indicators of weight efficiency and structural resource. This scientific problem is solved by studying the stress-strain state of the structure analytically, numerically or experimentally. Numerical modeling is increasingly and widely used in the design of aircraft structures to determine the optimal parameters at given operating modes. The main numerical method that has become widespread in engineering calculations is the finite element method.The main design case for the tail boom is the exit from a dive. The corresponding design load cases acting on the helicopter's tail boom are determined as a result of calculations performed in accordance with the requirements of the aviation rules and other regulatory documents for the creation of a transport category helicopter, as well as the results of tests.

  • Open Access

    Analysis of Effectiveness of Combined Surface Treatment Methods for Structural Parts with Holes to Enhance Their Fatigue Life

    by Olexander Grebenikov, Andrii Humennyi, Serhii Svitlychnyi, Vasyl Lohinov, Valerii Matviienko

    The typical and most widespread stress concentrators in the lower wing panels of aircraft are the drain holes located on the stringer vertical ribs. These are prime sources for the initiation and development of fatigue cracks, which lead to early failure of the wing structure. Therefore, improving fatigue life in these critical areas is one of the significant issues for research. Two combined methods of surface plastic treatment in the location around drain holes are discussed in this paper. Using the finite element method and ANSYS software, we created a finite element model and obtained nonlinear solution results in the case of tension in a plate with three holes. In addition, the development of residual stress due to the surface plastic treatment of the hole-adjacent areas was taken into account. In this paper, it is shown that after surface treatment of the corresponding areas of the holes, residual stress, which exceeds the yield stress for the plate material, is induced. When combined with alternative tensile stress, these reduce the amplitude of the local stresses, thus increasing the number of stress cycles before failure. The benefits of this technology were confirmed by fatigue test results, which include the fatigue failure types of the plates. Graphs showing the impact of applicable surface treatment combined methods on the number of cycles to failure were also plotted.


  • Open Access

    Design Method for Pressurised and Non-Pressurised Tail Cargo Door’s Fairings Compartment in Transport Category Aircraft

    by Oleksandr Grebenikov, Andrii Humennyi, Vasyl Loginov, Olexandr Dveirin, Dmytro Konyshev

    The method for determining the main parameters of the tail cargo doors of transport category aircrafts is developed. A methodology for the ascertainment of these parameters has been described. An example based on an existing transport aircraft is considered. Gathered were information pertaining to the necessary design, operational and regulatory parameters and requirements of the international regulatory organisations Federal Aviation Regulations (FAR), Certification Specification (CS) and Aviation Regulations (AR). The principle of determining the dimensions of the cargo compartment, cargo floor and the hitting platforms, in the form of a ramp with a pressure door and ladders, is presented based on the initial data. Considering the described loading and unloading, as well as landing, operations, the dependence of the ramp length on the length of the cargo floor is ascertained. A method for designing a cargo door fairings in the transport category aircraft fuselage tail part is presented. The main features of the fairings compartment have been determined, together with those of its main components and their varieties, depending on the scheme of the cargo door. Information is provided on the fairings compartment structural elements parameters selection.

  • Design of High Fatigue Life Joints of Fuselage Structures Considering Fracture Mechanics

    by Dmytro Zhyriakov, Oleksandr Grebenikov, Andrig Humennyi, Dmytro Konyshev


  • Open Access

    The KhAI-90 Light Civil Turboprop Airplane Pilot Project

    by Oleksandr Grebenikov, Vasyl Loginov, Andrii Humennyi, Liliia Buival, Anton Chumak

    The pilot project of new light civil turboprop aircraft, called the KhAI-90, featuring a cruising speed of 350km/h, payload of 600 kg at 500 km range, and equipped with two turboprop Rolls-Royce 250-B17F engines each with power of 420 hp (alternatively, two AI-450C engines each with power of 450 hp may be installed) is presented herein. Based on the developed technical task, the concept for creating the KhAI-90 new competitive light civil aircraft, and the analysis of prototypes’ aircraft parameters and characteristics, the main tactical and technical requirements are assigned. The take-off weight of the new aircraft is determined in three approximations at the preliminary design stage of light civil turboprop aircraft, using the iterative software “CLA-TOW”, studying the influence of the wing geometric parameters and lift devices on aerodynamic performance, the power-to-weight ratio and the airplane weight parameters. The following parameters are calculated for the design: minimum take-off weight WTO min = 3,600 kg, optimal wing loading p 0 opt = 130 daN/m2, optimal aspect ratio 9.6, taper ratio 2.25, sweep angle at leading edge 3 degrees, airfoil relative thickness 10.6%. A general view and three-dimensional parametric models of the master-geometry and passenger cabin space distribution are constructed for the KhAI-90 by means of the SIEMENS NX computer integrated system. More broadly, this pilot project has also demonstrated the viability of the method we developed and previously reported for determining light civil turboprop airplane parameters.

  • Open Access

    Devising a concept of integrated design and modeling of aircraft

    by Oleksandr Grebenikov, Andrii Humennyi, Oleksandr Dveirin, Oleksandr Soboliev, Lilia Buival

    The analysis of aircraft design methods reported here has revealed that building a competitive aircraft necessitates devising a scientifically based concept of integrated aircraft design employing CAD/CAM/CAE/PLM software suites. A generalized concept of integrated design and three-dimensional computer modeling of aircraft involving the CAD/CAM/CAE/PLM systems has been developed. Based on the proposed concept, the principles of integrated design of aircraft were devised. The features of designing the training and training-combat aircraft, transport-category aircraft, light civilian aircraft have been described. A method for determining the take-off weight, design parameters, and formation of the general appearance of aircraft has been improved. The method is intended to form the appearance of the aircraft at the stages of preliminary design, the purpose of which is reduced to determining the permissible version of the aircraft project. The project must meet the predefined requirements and restrictions in the selected aircraft scheme and the assigned set of parameters that characterize its airframe and power plant. A method of parametric modeling of aircraft has been improved, which includes the stages of creating a master geometry of the aircraft and a model of space distribution. Parametric models of master geometry and models of space distribution, training and training-combat aircraft, transport-category aircraft, light civilian aircraft have been constructed. Methods of integrated design of aircraft main units have been devised and theoretically substantiated. Parametric models of master geometry of the wing for a training aircraft, the wings, appendage, and fuselage of a light civilian aircraft were built, taking into consideration the design features of aircraft units of various categories


  • Open Access

    Preliminary Design for a Jet Training Aircraft

    by Vasyl Loginov, Oleksandr Grebenikov, Andrii Humennyi, Serhii Eremenko, Oleksandr Soboliev

    This paper present the results of our project to develop the preliminary design of a jet trainer plane (JTP) with a two-person crew, the base version of which is intended for cadet training. We first consider the assumptions and requirements for the new aircraft, and review the parameters of existing aircraft designs in the similarly-purposed class. Next we argue for certain design choices, regarding the aircraft layout, cockpit configuration, wing location and wingform, tail scheme, and powerplant. The resulting aircraft design is calculated to have a maximum flight speed of 940 km/h, a ground-level rate of climb of 100 m/s, and a range of 1130 km. The plane’s take-off mass is calculated, in three approximations, at 2264 kg. Lastly we present the training plane’s geometrical parameters, general view, and master geometry.

  • Transport Aircrafts Rear Cargo Door Ramp with Sealed Floor Main Parameters and Components Description and Determination

    by Dmytro Konyshev, Andriy Humennyi, Oleksandr Grebenikov, Anton Chumak, Liliya Buival

  • Transport Category Airplane Fuselage Master Geometry Parametrical Modeling Method

    by Anton Chumak, Liliia Buival, Andrii Humennyi, Oleksandr Grebenikov, Dmytro Konyshev