Oleksandr Dveirin
Research Subjects
Research Interests
Oleksandr Dveirin has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Andrii Kondratiev
O.M. Beketov National University of Urban Economy in Kharkiv
4 shared publications - Tetyana Nabokina
National Aerospace University “Kharkiv Aviation Institute
4 shared publications - Andrii Humennyi
National Aerospace University "Kharkiv Aviation Institute", Kharkiv
3 shared publications - Anton Tsaritsynskyi
National Aerospace University “Kharkiv Aviation Institute
2 shared publications - Dmytro Konyshev
State Company “Antonov
2 shared publications - Oleksandr Grebenikov
Kharkiv Aviation Institute – National Aerospace University , 17 Chkalov Str., Kharkiv, 61070 , Ukraine
2 shared publications
Latest Publications
- 27 September 2024
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1126, 49-60
Anisotropy of Composite Shearing Strength in the Mechanical Joints
Studying of the strength characteristics of polymer composite materials, which are used in the structures for various applications, is an important subject for research. Here one of the major issues is the development of fastening techniques to maximize the strength characteristics of composite fibers. Based on the modification of the available test methods, a set of specimens and devices has been developed to determine the shearing (cut) strength from the fastener hole to the edge of the composite part. For this purpose, we used the modified specimen sequentially shearing along the contour after each test cycle in order to find the required parameter depending on the distance from the fastener to the part edge. According to the result of experimental studies, possible types of shearing test and shear test failures were identified. It is demonstrated that shearing strength and shear strength in the specimen plane are different characteristics with no correlation between them. It is found that a shearing in the classic sense is observed only for high-anisotropy structures when they are loaded in the more rigid direction, whereas the complex modes of failure occur for the heavily reinforced composites used. For example, during testing a pure shearing was observed in 0° planes in the specimens with the package structure of [0°0.7; ±45°0.2; 90°0.1], while it was observed both for the holes drilled in 0° and 22.5° directions in the specimen with the structure of [0°0.8; ±45°0.2]. We obtained the quadratic engineering dependence to predict shearing strength of the heavily reinforced basic composite. Based on processing of the experimental results, a recommendation has been made on the need for constant experimental support of the design process, which can be implemented by the proposed specimen and testing device.
- 27 September 2024
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1126, 49-60
Anisotropy of Composite Shearing Strength in the Mechanical Joints
Studying of the strength characteristics of polymer composite materials, which are used in the structures for various applications, is an important subject for research. Here one of the major issues is the development of fastening techniques to maximize the strength characteristics of composite fibers. Based on the modification of the available test methods, a set of specimens and devices has been developed to determine the shearing (cut) strength from the fastener hole to the edge of the composite part. For this purpose, we used the modified specimen sequentially shearing along the contour after each test cycle in order to find the required parameter depending on the distance from the fastener to the part edge. According to the result of experimental studies, possible types of shearing test and shear test failures were identified. It is demonstrated that shearing strength and shear strength in the specimen plane are different characteristics with no correlation between them. It is found that a shearing in the classic sense is observed only for high-anisotropy structures when they are loaded in the more rigid direction, whereas the complex modes of failure occur for the heavily reinforced composites used. For example, during testing a pure shearing was observed in 0° planes in the specimens with the package structure of [0°0.7; ±45°0.2; 90°0.1], while it was observed both for the holes drilled in 0° and 22.5° directions in the specimen with the structure of [0°0.8; ±45°0.2]. We obtained the quadratic engineering dependence to predict shearing strength of the heavily reinforced basic composite. Based on processing of the experimental results, a recommendation has been made on the need for constant experimental support of the design process, which can be implemented by the proposed specimen and testing device.
- 11 November 2023
- Published by Springer Nature
- p. 169-207
Transport Category Aircraft Fuselage Integrated Design
- 11 November 2023
- Published by Springer Nature
- p. 169-207
Transport Category Aircraft Fuselage Integrated Design
- Open Access
- 1 September 2023
- Published by Walter de Gruyter GmbH in Transactions on Aerospace Research
- Vol. 2023 (3) , 55-71
Design Method for Pressurised and Non-Pressurised Tail Cargo Door’s Fairings Compartment in Transport Category Aircraft
The method for determining the main parameters of the tail cargo doors of transport category aircrafts is developed. A methodology for the ascertainment of these parameters has been described. An example based on an existing transport aircraft is considered. Gathered were information pertaining to the necessary design, operational and regulatory parameters and requirements of the international regulatory organisations Federal Aviation Regulations (FAR), Certification Specification (CS) and Aviation Regulations (AR). The principle of determining the dimensions of the cargo compartment, cargo floor and the hitting platforms, in the form of a ramp with a pressure door and ladders, is presented based on the initial data. Considering the described loading and unloading, as well as landing, operations, the dependence of the ramp length on the length of the cargo floor is ascertained. A method for designing a cargo door fairings in the transport category aircraft fuselage tail part is presented. The main features of the fairings compartment have been determined, together with those of its main components and their varieties, depending on the scheme of the cargo door. Information is provided on the fairings compartment structural elements parameters selection.
- 1 September 2023
- Published by Walter de Gruyter GmbH in Transactions on Aerospace Research
- Vol. 2023 (3) , 55-71
Open AccessDesign Method for Pressurised and Non-Pressurised Tail Cargo Door’s Fairings Compartment in Transport Category Aircraft
The method for determining the main parameters of the tail cargo doors of transport category aircrafts is developed. A methodology for the ascertainment of these parameters has been described. An example based on an existing transport aircraft is considered. Gathered were information pertaining to the necessary design, operational and regulatory parameters and requirements of the international regulatory organisations Federal Aviation Regulations (FAR), Certification Specification (CS) and Aviation Regulations (AR). The principle of determining the dimensions of the cargo compartment, cargo floor and the hitting platforms, in the form of a ramp with a pressure door and ladders, is presented based on the initial data. Considering the described loading and unloading, as well as landing, operations, the dependence of the ramp length on the length of the cargo floor is ascertained. A method for designing a cargo door fairings in the transport category aircraft fuselage tail part is presented. The main features of the fairings compartment have been determined, together with those of its main components and their varieties, depending on the scheme of the cargo door. Information is provided on the fairings compartment structural elements parameters selection.
- 26 November 2022
- Published by Springer Nature
- p. 208-218
Determination of Composite’s Bearing Strength in the Area of Circular Hole of Fastening Element
- 26 November 2022
- Published by Springer Nature
- p. 208-218
Determination of Composite’s Bearing Strength in the Area of Circular Hole of Fastening Element
- 15 July 2022
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 334, 162-172
Compliance of Fasteners in Metal-Composite Joints
The greatest difficulties in creating a new structure or upgrading an old one are associated with designing joints and connecting parts of the structure, especially composite and metal ones. Nowadays, the problem of designing and improving such joints is timely and is being actively studied so that the best solutions are found. The article presents the research carried out to determine the main parameters of elements of mechanical joints made of polymer composite materials, as factors affecting the requirements for precision of connection compliance estimation. There has been found the influence of the number of fastener rows on estimating the maximum forces which act in the joint, as well as the influence of the ratio of the connection compliance to the compliance of the part. A field of possible states of the joint has been built. Within the field, the following areas have been identified: the area of high sensitivity to precision of estimating the parameters of the joint elements, requiring experimental confirmation and more accurate models; the area of average sensitivity of the joint to precision of estimating the parameters of its elements, permitting the use of known dependences; and the area of low sensitivity, where simplified models can be used. In the course of the developed model testing, joint samples were tested to evaluate the force connection compliance, and a reference variant was calculated using the Douglas formula. The reference variant of the joint sample was chosen based on the principle of equal compliances of the parts to be joined, presented by a series of samples assembled from a composite package of 80 layers and two surface layers made of 3.98 mm-thick steel. The parts were connected with steel bolts with a diameter of 6 and 8 mm. Numerically, the ratio of the connection compliance to the part compliance is 85...96 for the experimental data, and 9...10 for the calculated data. This indicated that the joint was in the transition area between high and medium sensitivity of the joint to the accuracy of compliance estimation, which requires continuous refinement of the connection parameters.
- 15 July 2022
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 334, 162-172
Compliance of Fasteners in Metal-Composite Joints
The greatest difficulties in creating a new structure or upgrading an old one are associated with designing joints and connecting parts of the structure, especially composite and metal ones. Nowadays, the problem of designing and improving such joints is timely and is being actively studied so that the best solutions are found. The article presents the research carried out to determine the main parameters of elements of mechanical joints made of polymer composite materials, as factors affecting the requirements for precision of connection compliance estimation. There has been found the influence of the number of fastener rows on estimating the maximum forces which act in the joint, as well as the influence of the ratio of the connection compliance to the compliance of the part. A field of possible states of the joint has been built. Within the field, the following areas have been identified: the area of high sensitivity to precision of estimating the parameters of the joint elements, requiring experimental confirmation and more accurate models; the area of average sensitivity of the joint to precision of estimating the parameters of its elements, permitting the use of known dependences; and the area of low sensitivity, where simplified models can be used. In the course of the developed model testing, joint samples were tested to evaluate the force connection compliance, and a reference variant was calculated using the Douglas formula. The reference variant of the joint sample was chosen based on the principle of equal compliances of the parts to be joined, presented by a series of samples assembled from a composite package of 80 layers and two surface layers made of 3.98 mm-thick steel. The parts were connected with steel bolts with a diameter of 6 and 8 mm. Numerically, the ratio of the connection compliance to the part compliance is 85...96 for the experimental data, and 9...10 for the calculated data. This indicated that the joint was in the transition area between high and medium sensitivity of the joint to the accuracy of compliance estimation, which requires continuous refinement of the connection parameters.
- 1 January 2022
- Published by Springer Nature
- p. 14-25
Assessment of Error of the Experimental Determination of Interlaminar Shear Strength
- 1 January 2022
- Published by Springer Nature
- p. 14-25
Assessment of Error of the Experimental Determination of Interlaminar Shear Strength
- Open Access
- 31 October 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (1(113)) , 15-23
Devising a concept of integrated design and modeling of aircraft
The analysis of aircraft design methods reported here has revealed that building a competitive aircraft necessitates devising a scientifically based concept of integrated aircraft design employing CAD/CAM/CAE/PLM software suites. A generalized concept of integrated design and three-dimensional computer modeling of aircraft involving the CAD/CAM/CAE/PLM systems has been developed. Based on the proposed concept, the principles of integrated design of aircraft were devised. The features of designing the training and training-combat aircraft, transport-category aircraft, light civilian aircraft have been described. A method for determining the take-off weight, design parameters, and formation of the general appearance of aircraft has been improved. The method is intended to form the appearance of the aircraft at the stages of preliminary design, the purpose of which is reduced to determining the permissible version of the aircraft project. The project must meet the predefined requirements and restrictions in the selected aircraft scheme and the assigned set of parameters that characterize its airframe and power plant. A method of parametric modeling of aircraft has been improved, which includes the stages of creating a master geometry of the aircraft and a model of space distribution. Parametric models of master geometry and models of space distribution, training and training-combat aircraft, transport-category aircraft, light civilian aircraft have been constructed. Methods of integrated design of aircraft main units have been devised and theoretically substantiated. Parametric models of master geometry of the wing for a training aircraft, the wings, appendage, and fuselage of a light civilian aircraft were built, taking into consideration the design features of aircraft units of various categories
- 31 October 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (1(113)) , 15-23
Open AccessDevising a concept of integrated design and modeling of aircraft
The analysis of aircraft design methods reported here has revealed that building a competitive aircraft necessitates devising a scientifically based concept of integrated aircraft design employing CAD/CAM/CAE/PLM software suites. A generalized concept of integrated design and three-dimensional computer modeling of aircraft involving the CAD/CAM/CAE/PLM systems has been developed. Based on the proposed concept, the principles of integrated design of aircraft were devised. The features of designing the training and training-combat aircraft, transport-category aircraft, light civilian aircraft have been described. A method for determining the take-off weight, design parameters, and formation of the general appearance of aircraft has been improved. The method is intended to form the appearance of the aircraft at the stages of preliminary design, the purpose of which is reduced to determining the permissible version of the aircraft project. The project must meet the predefined requirements and restrictions in the selected aircraft scheme and the assigned set of parameters that characterize its airframe and power plant. A method of parametric modeling of aircraft has been improved, which includes the stages of creating a master geometry of the aircraft and a model of space distribution. Parametric models of master geometry and models of space distribution, training and training-combat aircraft, transport-category aircraft, light civilian aircraft have been constructed. Methods of integrated design of aircraft main units have been devised and theoretically substantiated. Parametric models of master geometry of the wing for a training aircraft, the wings, appendage, and fuselage of a light civilian aircraft were built, taking into consideration the design features of aircraft units of various categories