Mykhailo Kholodov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mykhailo Kholodov has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Anton Kholodov
Kharkiv National Automobile and Highway University
4 shared publications - Mikhail Podrigalo
National Academy of the National Guard of Ukraine
4 shared publications Dmytro Klets
Kharkov National Auto and Highway University
3 shared publicationsMikhail Podrigalo
Kharkov National Auto and Highway University
3 shared publicationsVolodymyr Rudzinskyi
Zhytomyr State Technological University
3 shared publications- Dmytro Klets
Kharkiv National Automobile and Highway University
2 shared publications
Latest Publications
- Open Access
- 29 April 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (3 (134)) , 25-36
Improving the efficiency of transportation convoys using unmanned vehicles
The object of this study is the movement process of a vehicle convoy formed with the help of unmanned vehicles. The research aims to solve the task related to improving the controllability, maneuverability, energy efficiency of vehicle convoys, as well as the throughput capacity of roads. One of the ways to address this issue is the use of unmanned vehicles. The subject of this study is the assessment of the possibility to improve the indicators of maneuverability, controllability, energy efficiency of vehicle convoys, as well as the throughput capacity of roads, through the use of unmanned vehicles. During the study, the concepts of controllability and maneuverability of unmanned vehicle convoys have been defined. The relationship between the use of unmanned vehicles and the improvement of maneuverability and controllability of convoys was established. The use of unmanned vehicles makes it possible to eliminate the need to consider braking distance when setting inter-vehicle distances and to reduce the safety gap from 5 meters to zero. The paper shows that the use of unmanned vehicle convoys improves maneuverability and controllability compared to conventional convoys. For example, the time to pass a short road section for a convoy of 40 vehicles traveling at 90 km/h is reduced by 60 seconds, and the length of a convoy of 20 vehicles moving at the same speed is reduced by 800 meters. An evaluation of the reduction in energy consumption for convoys with unmanned vehicles was carried out. A condition was derived, the fulfillment of which ensures a reduction in additional engine energy losses through the use of unmanned vehicles in a convoy. Applying the results will make it possible to bring the efficiency of road transport to the level of railroad transport, which is achieved by assembling vehicle trains
- 29 April 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (3 (134)) , 25-36
Open AccessImproving the efficiency of transportation convoys using unmanned vehicles
The object of this study is the movement process of a vehicle convoy formed with the help of unmanned vehicles. The research aims to solve the task related to improving the controllability, maneuverability, energy efficiency of vehicle convoys, as well as the throughput capacity of roads. One of the ways to address this issue is the use of unmanned vehicles. The subject of this study is the assessment of the possibility to improve the indicators of maneuverability, controllability, energy efficiency of vehicle convoys, as well as the throughput capacity of roads, through the use of unmanned vehicles. During the study, the concepts of controllability and maneuverability of unmanned vehicle convoys have been defined. The relationship between the use of unmanned vehicles and the improvement of maneuverability and controllability of convoys was established. The use of unmanned vehicles makes it possible to eliminate the need to consider braking distance when setting inter-vehicle distances and to reduce the safety gap from 5 meters to zero. The paper shows that the use of unmanned vehicle convoys improves maneuverability and controllability compared to conventional convoys. For example, the time to pass a short road section for a convoy of 40 vehicles traveling at 90 km/h is reduced by 60 seconds, and the length of a convoy of 20 vehicles moving at the same speed is reduced by 800 meters. An evaluation of the reduction in energy consumption for convoys with unmanned vehicles was carried out. A condition was derived, the fulfillment of which ensures a reduction in additional engine energy losses through the use of unmanned vehicles in a convoy. Applying the results will make it possible to bring the efficiency of road transport to the level of railroad transport, which is achieved by assembling vehicle trains
- Open Access
- 10 October 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Hydraulic machines and hydraulic units
- No. 1,p. 35-42
ANALYSIS OF DYNAMICS OF VOLUME HYDRAULIC POWER STEERING SELF-PROPELLED TRACTOR CHASSIS
Goal. Analysis of the dynamics of the hydraulic fluid power steering drive of the wheeled tractor self-propelled chassis СШ2540 by simulating the operation of a hydraulic cylinder with a one-sided rod for moving the steering trapezoid when turning the wheels and studying the change in the pressure of the working fluid and the movement of the hydraulic cylinder rod under different load modes. Research methodology. The method of simulation modeling is used, when the variables describing the behavior of the steering hydraulic cylinder are determined by certain load algorithms and operating fluid flows, and are described by differential equations. The differential equations that determine the pressure of the working fluid in the cavities of the hydraulic cylinder and the movement of its rod when the working fluid is fed into the piston or rod cavity are based on the laws of mechanics, the principle of the continuity of the flow of the working fluid and its compressibility. The VisSim package of application programs was used for modeling according to the proposed methodology. The changes of the parameters in the hydraulic cylinder of turning the wheels when they are shifted from the task of the control action in the form of an increase in the external load and the flow of the working fluid in the output channels of the metering pump overcome by the hydraulic cylinder were studied. The influence of the modulus of elasticity of the working fluid, which decreases when it is saturated with undissolved air, was also investigated. The results. When starting the hydraulic steering drive, i.e. when turning the steering wheel from its neutral position, depending on the external load and the intensity of the driver's work at the wheel, oscillatory processes take place in the hydraulic cylinder cavities, which can significantly exceed the working pressure. The results of the research give a reason to conclude that it is necessary to study the nature of the increase in the flow rate and pressure of the working fluid on a full-scale sample of the tractor chassis metering pump, i.e. by replacing the flow rate simulation with its actual value. Setting the loading time and flow rate of the working fluid using the map-VisSim unit is more convenient than setting it with analytical expressions, as it makes it possible to simulate different acceleration rates of the hydraulic cylinder and, if necessary, to control the stationary mode of the steering wheel in the neutral position.
- 10 October 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Hydraulic machines and hydraulic units
- No. 1,p. 35-42
Open AccessANALYSIS OF DYNAMICS OF VOLUME HYDRAULIC POWER STEERING SELF-PROPELLED TRACTOR CHASSIS
Goal. Analysis of the dynamics of the hydraulic fluid power steering drive of the wheeled tractor self-propelled chassis СШ2540 by simulating the operation of a hydraulic cylinder with a one-sided rod for moving the steering trapezoid when turning the wheels and studying the change in the pressure of the working fluid and the movement of the hydraulic cylinder rod under different load modes. Research methodology. The method of simulation modeling is used, when the variables describing the behavior of the steering hydraulic cylinder are determined by certain load algorithms and operating fluid flows, and are described by differential equations. The differential equations that determine the pressure of the working fluid in the cavities of the hydraulic cylinder and the movement of its rod when the working fluid is fed into the piston or rod cavity are based on the laws of mechanics, the principle of the continuity of the flow of the working fluid and its compressibility. The VisSim package of application programs was used for modeling according to the proposed methodology. The changes of the parameters in the hydraulic cylinder of turning the wheels when they are shifted from the task of the control action in the form of an increase in the external load and the flow of the working fluid in the output channels of the metering pump overcome by the hydraulic cylinder were studied. The influence of the modulus of elasticity of the working fluid, which decreases when it is saturated with undissolved air, was also investigated. The results. When starting the hydraulic steering drive, i.e. when turning the steering wheel from its neutral position, depending on the external load and the intensity of the driver's work at the wheel, oscillatory processes take place in the hydraulic cylinder cavities, which can significantly exceed the working pressure. The results of the research give a reason to conclude that it is necessary to study the nature of the increase in the flow rate and pressure of the working fluid on a full-scale sample of the tractor chassis metering pump, i.e. by replacing the flow rate simulation with its actual value. Setting the loading time and flow rate of the working fluid using the map-VisSim unit is more convenient than setting it with analytical expressions, as it makes it possible to simulate different acceleration rates of the hydraulic cylinder and, if necessary, to control the stationary mode of the steering wheel in the neutral position.
- Open Access
- 26 July 2023
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 52,p. 41-53
To the issue of decomposition of mathematical models of disturbed motion of complex discrete-continuous dynamic systems
Problem. Usually, complex dynamic systems are characterized by a high order of equations in their mathematical models and intricate interconnections among subsystems that constitute the complex dynamic system. Naturally, the analysis and synthesis of complex dynamic systems require the use of powerful computational systems with vast memory and high processing speed. Goal. The aim is quantitative assessment of the influence of the continuum part of a dynamic system on the behavior of its discrete part and the possibility to perform decomposition of the mathematical model of perturbed motion of a discrete-continuum system based on this assessment. Methodology. The measures are aimed at addressing issues that are based on the discrete-continuum capabilities and their decomposition. Results. For three types of complex dynamic systems described by infinite-dimensional systems of ordinary differential equations, quantitative assessments of the influence of the continuum part on the discrete part of the system have been proposed. These assessments determine the decomposition of the mathematical models of perturbed motion for such systems. Originality. Simplified mathematical models for three types of discrete-continuous dynamic systems were obtained. Practical value. The obtained results can be recommended for the study of the specialized course on the motion characteristics of cargo trucks during the transportation of liquids in tanks. Through optimization using the MATLAB software package, it is possible to simulate various parameters of both the cargo truck and the cargo being transported.
- 26 July 2023
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 52,p. 41-53
Open AccessTo the issue of decomposition of mathematical models of disturbed motion of complex discrete-continuous dynamic systems
Problem. Usually, complex dynamic systems are characterized by a high order of equations in their mathematical models and intricate interconnections among subsystems that constitute the complex dynamic system. Naturally, the analysis and synthesis of complex dynamic systems require the use of powerful computational systems with vast memory and high processing speed. Goal. The aim is quantitative assessment of the influence of the continuum part of a dynamic system on the behavior of its discrete part and the possibility to perform decomposition of the mathematical model of perturbed motion of a discrete-continuum system based on this assessment. Methodology. The measures are aimed at addressing issues that are based on the discrete-continuum capabilities and their decomposition. Results. For three types of complex dynamic systems described by infinite-dimensional systems of ordinary differential equations, quantitative assessments of the influence of the continuum part on the discrete part of the system have been proposed. These assessments determine the decomposition of the mathematical models of perturbed motion for such systems. Originality. Simplified mathematical models for three types of discrete-continuous dynamic systems were obtained. Practical value. The obtained results can be recommended for the study of the specialized course on the motion characteristics of cargo trucks during the transportation of liquids in tanks. Through optimization using the MATLAB software package, it is possible to simulate various parameters of both the cargo truck and the cargo being transported.
- Open Access
- 7 May 2023
- Published by Private Company Technology Center
- p. 172-179
Hybrid drives as a way to efficient road construction
Effective use of means, including financial ones, in today's realities is the primary task of every region, every industry, every enterprise. Taking into account the scale of destruction of the road complex caused by military aggression, this task is particularly urgent. One of the methods of such savings in road construction is the use of hybrid drives. The impact of modern technologies in the field of creating hybrid drives on increasing the effective construction of the road construction complex as a whole is considered. The strategy for the development of hybrid drives of earthmoving machines (EMM) is considered on the example of the world's leading manufacturers of equipment. An analysis of the structural performance of the power drive as a whole and its individual elements, the interaction of power plant units in different operating modes is given.
- 7 May 2023
- Published by Private Company Technology Center
- p. 172-179
Open AccessHybrid drives as a way to efficient road construction
Effective use of means, including financial ones, in today's realities is the primary task of every region, every industry, every enterprise. Taking into account the scale of destruction of the road complex caused by military aggression, this task is particularly urgent. One of the methods of such savings in road construction is the use of hybrid drives. The impact of modern technologies in the field of creating hybrid drives on increasing the effective construction of the road construction complex as a whole is considered. The strategy for the development of hybrid drives of earthmoving machines (EMM) is considered on the example of the world's leading manufacturers of equipment. An analysis of the structural performance of the power drive as a whole and its individual elements, the interaction of power plant units in different operating modes is given.
- Open Access
- 29 December 2022
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 51,p. 26-34
Assessment of increased energy efficiency of vehicles with a rational reduction of engine capacity
Problem. The tendency to reduce the working volume of internal combustion engines, which has emerged in recent years in the global automotive industry, is due to the need to improve the environmental situation and energy efficiency of road transport. Goal. The aim of the study is to increase the energy efficiency of vehicles by rationally reducing the maximum effective engine capacity. Methodology. The work uses the method of partial accelerations, implemented in a mobile registration and measurement complex, which allowed the authors to obtain an improved formula for calculating the force of aerodynamic resistance. Experimental studies of car aerodynamics were also carried out. Results. The article presents the results of the authors' research, which made it possible to prove the possibility of reducing the power of the internal combustion engine while maintaining the specified maximum speed and the specified level of indicators of the dynamic properties of cars. Originality. The relationship between the degree of use of the maximum engine power and the relative change in the effective specific fuel consumption of a carburetor gasoline engine with direct injection of gasoline and diesel is determined. Practical value. Calculations performed on the example of the ZAZ-1103 "Slavuta" car showed that a rational reduction in effective power allows for a 9.5% reduction in fuel consumption, and for an engine with direct injection of gasoline and diesel engines, this leads to an increase in fuel consumption by 6.7 % and 20.3%, respectively.
- 29 December 2022
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 51,p. 26-34
Open AccessAssessment of increased energy efficiency of vehicles with a rational reduction of engine capacity
Problem. The tendency to reduce the working volume of internal combustion engines, which has emerged in recent years in the global automotive industry, is due to the need to improve the environmental situation and energy efficiency of road transport. Goal. The aim of the study is to increase the energy efficiency of vehicles by rationally reducing the maximum effective engine capacity. Methodology. The work uses the method of partial accelerations, implemented in a mobile registration and measurement complex, which allowed the authors to obtain an improved formula for calculating the force of aerodynamic resistance. Experimental studies of car aerodynamics were also carried out. Results. The article presents the results of the authors' research, which made it possible to prove the possibility of reducing the power of the internal combustion engine while maintaining the specified maximum speed and the specified level of indicators of the dynamic properties of cars. Originality. The relationship between the degree of use of the maximum engine power and the relative change in the effective specific fuel consumption of a carburetor gasoline engine with direct injection of gasoline and diesel is determined. Practical value. Calculations performed on the example of the ZAZ-1103 "Slavuta" car showed that a rational reduction in effective power allows for a 9.5% reduction in fuel consumption, and for an engine with direct injection of gasoline and diesel engines, this leads to an increase in fuel consumption by 6.7 % and 20.3%, respectively.
- Open Access
- 24 December 2021
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 49,p. 36-44
Improvement evaluation methodology of vehicle load and energy efficiency
Анотація Проблема. Виникла необхідність розширити відому концепцію експлуатаційних властивостей автомобіля - економічність палива виникла у зв'язку з появою нових альтернативних електростанцій (електродвигуни, маховики, гібридні електростанції тощо), що вимагає включення не тільки теплову енергію палива, але й інші види енергії (електричну та механічну). У статті проведено дослідження вибору та обґрунтування показників енергоефективності автомобіля шляхом оцінки витрат енергії двигуна на його рух. Було проведено аналіз взаємозв’язку між енергетичними характеристиками динаміки та ефективністю автомобіля. Мета. Метою дослідження є аналіз методів оцінки енергоефективності транспортного засобу. Для досягнення цієї мети необхідно визначити показники, які дозволять проводити порівняльний аналіз показників енергоефективності різних транспортних засобів. Методологія. Підходи, прийняті в роботі для вирішення цієї мети, ґрунтуються на обґрунтуванні показників енергоефективності автомобіля шляхом оцінки споживання енергії двигуном на його рух. Результати. На нашу думку, при проектуванні та оцінці динамічних властивостей транспортних засобів раціонально використовувати енергетичні показники транспортного засобу, для яких необхідно розробити відповідні критерії оцінки. Аналіз результатів розрахунку показників і, у таблиці 1, показав, що показник у порівнянні з має меншу дисперсію. Оригінальність. Отримані результати впливу параметрів транспортних засобів на рівень їх енергетичного навантаження показують, що показник має меншу дисперсію, ніж. Крім того, значення не корелює з роком випуску автомобіля, що дозволяє використовувати цей показник на етапі проектування транспортних засобів. Необхідно лише встановити раціональне нормативне значення цього показника. Практичне значення. Отримані результати можна рекомендувати спеціалістам для використання при проектуванні, виробництві, сертифікації та експлуатації автомобільних транспортних засобів, енергоефективності транспортних засобів, комбінованої електростанції.
- 24 December 2021
- Published by Kharkiv National Automobile and Highway University in Automobile Transport
- No. 49,p. 36-44
Open AccessImprovement evaluation methodology of vehicle load and energy efficiency
Анотація Проблема. Виникла необхідність розширити відому концепцію експлуатаційних властивостей автомобіля - економічність палива виникла у зв'язку з появою нових альтернативних електростанцій (електродвигуни, маховики, гібридні електростанції тощо), що вимагає включення не тільки теплову енергію палива, але й інші види енергії (електричну та механічну). У статті проведено дослідження вибору та обґрунтування показників енергоефективності автомобіля шляхом оцінки витрат енергії двигуна на його рух. Було проведено аналіз взаємозв’язку між енергетичними характеристиками динаміки та ефективністю автомобіля. Мета. Метою дослідження є аналіз методів оцінки енергоефективності транспортного засобу. Для досягнення цієї мети необхідно визначити показники, які дозволять проводити порівняльний аналіз показників енергоефективності різних транспортних засобів. Методологія. Підходи, прийняті в роботі для вирішення цієї мети, ґрунтуються на обґрунтуванні показників енергоефективності автомобіля шляхом оцінки споживання енергії двигуном на його рух. Результати. На нашу думку, при проектуванні та оцінці динамічних властивостей транспортних засобів раціонально використовувати енергетичні показники транспортного засобу, для яких необхідно розробити відповідні критерії оцінки. Аналіз результатів розрахунку показників і, у таблиці 1, показав, що показник у порівнянні з має меншу дисперсію. Оригінальність. Отримані результати впливу параметрів транспортних засобів на рівень їх енергетичного навантаження показують, що показник має меншу дисперсію, ніж. Крім того, значення не корелює з роком випуску автомобіля, що дозволяє використовувати цей показник на етапі проектування транспортних засобів. Необхідно лише встановити раціональне нормативне значення цього показника. Практичне значення. Отримані результати можна рекомендувати спеціалістам для використання при проектуванні, виробництві, сертифікації та експлуатації автомобільних транспортних засобів, енергоефективності транспортних засобів, комбінованої електростанції.
- 30 August 2020
- Published by Springer Nature
- p. 92-100
Modelling and Simulation of Metal Construction Stress-Strain Behaviour When Designing Road-Building Machines
- 30 August 2020
- Published by Springer Nature
- p. 92-100
Modelling and Simulation of Metal Construction Stress-Strain Behaviour When Designing Road-Building Machines
- 15 September 2019
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Analysis of the Tractor-Trailer Dynamics during Braking
The intensive development of tractor-building industry in the world has led to the widespread use of wheeled tractors and tractor trains in transportations on public highways. This requires an increase of engine capacity and speed of tractor trains, as well as strict demands for their braking systems.The formation of the necessary braking properties of wheeled tractors and tractor trains on their basis should be carried out at the design phase, taking into account a wide range of aggregated machines and tools.Blocking the wheels of the trailer with different sequence of their blocking and blocking the wheels of the tractor has significant impact on the total braking force, deceleration and stability of the tractor train. It is advisable to take this into account when modeling the braking process of a tractor train.The article deals with the braking dynamics of the tractor train and the impact of the dynamic distribution of normal reactions between the axles on the brake properties of the tractor train. The mathematical model of the braking process of the tractor-trailer train (consisting of a wheeled tractor and a two-axle trailer at the limit of blocking the wheels) has been obtained. The coefficients of the total braking force distribution between the to the front and rear axles of the tractor, front and rear axles of the trailer, ensuring the directional stability of the tractor-trailer train, have been determined.
- 15 September 2019
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Analysis of the Tractor-Trailer Dynamics during Braking
The intensive development of tractor-building industry in the world has led to the widespread use of wheeled tractors and tractor trains in transportations on public highways. This requires an increase of engine capacity and speed of tractor trains, as well as strict demands for their braking systems.The formation of the necessary braking properties of wheeled tractors and tractor trains on their basis should be carried out at the design phase, taking into account a wide range of aggregated machines and tools.Blocking the wheels of the trailer with different sequence of their blocking and blocking the wheels of the tractor has significant impact on the total braking force, deceleration and stability of the tractor train. It is advisable to take this into account when modeling the braking process of a tractor train.The article deals with the braking dynamics of the tractor train and the impact of the dynamic distribution of normal reactions between the axles on the brake properties of the tractor train. The mathematical model of the braking process of the tractor-trailer train (consisting of a wheeled tractor and a two-axle trailer at the limit of blocking the wheels) has been obtained. The coefficients of the total braking force distribution between the to the front and rear axles of the tractor, front and rear axles of the trailer, ensuring the directional stability of the tractor-trailer train, have been determined.
- 15 September 2019
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Stability of Wheel Tractors during Braking
The dynamic distribution of normal reactions between the axles of the wheeled tractor has a significant impact on the stability against skidding and the wheeled tractor braking effectiveness. At the same time, the clarification of the normal reactions distribution between the axles allows to choose more rational braking forces distribution between the axles. It is shown that the best way to ensure the highest braking efficiency is the braking mode when the rear wheels of the tractor are at the blocking limit. An assessment of the expediency of installing brake mechanisms on only one axle of the tractor was made. The increase of braking efficiency of wheeled tractors with all brake wheels provided that they ensure directional stability is considered. The laws of braking forces distribution between the axles of wheel tractors for different sequence of wheels locking are determined. Using the method of partial accelerations an improved method for estimating the effect of a brake system on the stability of wheeled tractor is proposed. The criterion in the form of angular acceleration in the road plane ώz, by the value and sign of which one we can estimate the operational stability of the brake mechanisms has obtained.
- 15 September 2019
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Stability of Wheel Tractors during Braking
The dynamic distribution of normal reactions between the axles of the wheeled tractor has a significant impact on the stability against skidding and the wheeled tractor braking effectiveness. At the same time, the clarification of the normal reactions distribution between the axles allows to choose more rational braking forces distribution between the axles. It is shown that the best way to ensure the highest braking efficiency is the braking mode when the rear wheels of the tractor are at the blocking limit. An assessment of the expediency of installing brake mechanisms on only one axle of the tractor was made. The increase of braking efficiency of wheeled tractors with all brake wheels provided that they ensure directional stability is considered. The laws of braking forces distribution between the axles of wheel tractors for different sequence of wheels locking are determined. Using the method of partial accelerations an improved method for estimating the effect of a brake system on the stability of wheeled tractor is proposed. The criterion in the form of angular acceleration in the road plane ώz, by the value and sign of which one we can estimate the operational stability of the brake mechanisms has obtained.
- 15 September 2019
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
The Improvement Brake’s Qualities of Vehicle by Developing the Method of the Choosing Frictional Pairs of the Brakes Mechanisms
One of the reasons for the large number of road accidents on highways in Ukraine [1] is the instability of the braking properties due to the unstable characteristics of the brake mechanisms’ friction pairs. The manufacturer produces new automobiles with installed brake pairs (brake pads and their counter bodies), which have passed long-term tests for the stability of the friction coefficient and braking forces distribution of between the axles. This ensures the compatibility of the friction pairs characteristics for front and rear brake mechanisms according to the criteria of heat resistance. During operation, instead of worn-out brake pads, brake discs and drums, drivers can purchase new ones, manufactured as spare parts. However, in the well-known literature there are no methods that allow to check the compatibility of the friction pairs characteristics for front and rear brake mechanisms according to the criteria of heat resistance. In the article a method for choosing a set of friction pairs of brake mechanisms for passenger car during operation is proposed. Assessment of the compatibility of the friction pairs characteristics for front and rear brake mechanisms was carried out according to the criteria of heat resistance.
- 15 September 2019
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
The Improvement Brake’s Qualities of Vehicle by Developing the Method of the Choosing Frictional Pairs of the Brakes Mechanisms
One of the reasons for the large number of road accidents on highways in Ukraine [1] is the instability of the braking properties due to the unstable characteristics of the brake mechanisms’ friction pairs. The manufacturer produces new automobiles with installed brake pairs (brake pads and their counter bodies), which have passed long-term tests for the stability of the friction coefficient and braking forces distribution of between the axles. This ensures the compatibility of the friction pairs characteristics for front and rear brake mechanisms according to the criteria of heat resistance. During operation, instead of worn-out brake pads, brake discs and drums, drivers can purchase new ones, manufactured as spare parts. However, in the well-known literature there are no methods that allow to check the compatibility of the friction pairs characteristics for front and rear brake mechanisms according to the criteria of heat resistance. In the article a method for choosing a set of friction pairs of brake mechanisms for passenger car during operation is proposed. Assessment of the compatibility of the friction pairs characteristics for front and rear brake mechanisms was carried out according to the criteria of heat resistance.