OKOleksii Kulyk

Oleksii Kulyk

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Oleksii Kulyk has a total of 23 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Prospects for the creation of small-sized high-speed unmanned aerial vehicles based on WIG-craft

    by Andrii Dreus, Sergey Alekseyenko, Oleksii Kulyk, Valeriі Nekrasov

    WIG-craft are high-speed vehicles that use the dynamic principle of support above the ground. Today, the current examples and projects of such vessels concern, mainly, only large-sized or medium-sized manned vehicles, for which it is possible to ensure stable aerodynamic characteristics during flight. At the same time, modern trends in the development of vehicles indicate a growing interest in small unmanned vehicles. Currently, the issue of creating small manned and unmanned WIG-crafts has become relevant. In the presented work, based on the von Karman–Gabrielli methodology, the efficiency of transport WIG-craft among other types of vehicles was evaluated. The possibility of using such small-sized devices as unmanned devices is considered. The productivity of a WIG-craft is depends on its aerodynamic characteristics. Scale factor is very important for WIG-craft, because the aerodynamics is depended on wings size. The design of a small-sized WIG-craft based on the aerodynamic scheme of an airplane is proposed. The aerodynamic characteristics of the proposed device were evaluated using CFD modeling. Outcomes indicates that the aerodynamic properties of a ship are greatly affected by clearance and velocity. Ground effect is allowed to increase the aerodynamic quality up to 1.5 times, provide the transport of payloads at velocities as high as 250 km/h with a take-off weight of 2.7 tons. The analysis of computation results shows that the proposed project of an unmanned WIG-craft is fully operational and promising for solving the problems of high-speed delivery of small payloads. According to the computation results of the aerodynamic characteristics, the specific power of the device was determined, which indicates the high theoretical efficiency of the proposed means.


  • Open Access

    Верифікація методичних підходів до оцінки характеристик твердих сумішевих ракетних палив

    by Vladyslav Proroka, Vadym Solntsev, Oleksii Kulyk, Oleksandr Dobrodomov, Artem Shvets, Illia Lukianenko, Mykola Dron

    Предметом вивчення в статті є процеси теоретичної оцінки основних параметрів твердих сумішевих ракетних палив. Метою є верифікація існуючих методик оцінки параметрів твердих сумішевих ракетних палив шляхом порівняння цих результатів з експериментальними даними, що були отримані в ході проведення стендових вогневих випробувань реальних ракетних двигунів з тягою до 5000 Н. Завдання: провести пошук та аналіз методичних підходів до оцінки параметрів твердих сумішевих ракетних палив, включаючи використання програмного забезпечення, що допомагає виконувати дану задачу; виконати співставлення результатів розрахунків з використанням обраного програмного забезпечення та аналітичними залежностями динаміки газового потоку; дослідити вплив фактору наявності конденсованої фази на основні параметри палив; провести стендові вогневі випробування серії ракетних двигунів твердого палива з тягою до 5000 Н з фіксацією основних параметрів їх роботи; обробити дані, отримані в ході проведення стендових вогневих випробувань; порівняти результати стендових випробувань з даними, отриманими за існуючими теоретичними методиками. Отримані такі результати. Порівняння розрахованих параметрів твердих сумішевих ракетних палив, отриманих за допомогою програмного забезпечення ProPEP 3 та аналітичними залежностями динаміки газового потоку показують близькі результати. Обрані для розгляду у роботі два варіанти ракетних палив мають значний ступінь металізації з використанням порошку алюмінію. Враховуючи це, а також невеликий розмір ракетних двигунів твердого палива, які випробовувалися в ході вогневих випробувань, значною мірою проявляється вплив фактору наявності у продуктах згорання конденсованої фази. Існуюча методика розрахунку параметрів двофазного газового потоку дає результати, що значною мірою підтверджуються експериментальними даними, отриманими в ході стендових випробувань. Для розглянутих ракетних двигунів твердого палива показано, що збільшення ступеню металізації, незважаючи на протилежні результати отримані з припущення поведінки продуктів згорання як ідеального газу, не призводить до реального зростання питомої тяги і супроводжується збільшенням температури всередині камери згорання. Висновки. Встановлено, що відносне відсоткове відхилення по величині питомого імпульсу між експериментальними та розрахунковими даними складає менше 3%, що дозволяє говорити про високий показник співпадіння між розглянутою методикою та експериментальними даними для двигунів обраного розміру та величини тяги.


  • Open Access

    Вдосконалення процесу обробки абразивно-повітряним струменем робочих поверхонь лопаток моноколіс закритого типу на основі даних чисельного моделювання за допомогою програмного комплексу ANSYS CFX

    by Yurii Shashko, Oleksiy Kulyk

    The correct choice of technological modes can guarantee the results of inkjet processing. However, the need to consider a significant amount of input data, namely the parameters of the equipment, the abrasive jet, the physical and mechanical properties of the material, and the shape of the processed product surfaces, as well as the lack of clear recommendations and technological data, significantly complicates the process. The subject of this study is the process of processing the surface of closed-type blades with an abrasive-air jet made in one piece with a disk of the "monowheel" type, using the SLM technology of Inconel 718 alloy. The goal of this task is to model the jet processing of closed-type monowheel blades using the ANSYS CFX finite element analysis software system. This article presents the results of numerical modeling of the surface treatment of closed turbine blades and the identification of technological factors that affect the roughness and quality of the surface of the compressed air environment on samples of closed turbine blades made of Inconel 718 alloy. The task: to develop a research plan and study the processing process and accompanying phenomena occurring during processing using the finite element method using the ANSYS CFX software complex, considering the physical and mechanical properties of the abrasive often, the environment, and the processed material. The following results were obtained: during mathematical modeling using the finite element method, data were obtained for sixteen calculation variants of blade surface treatment, from which the most optimal one was chosen, which provides the largest contact area of abrasive particles and their uniform interaction with the processing surface. In addition, during the research, the impact of "unevenness of erosion" and the graininess of abrasive materials on the quality of the treated surface was studied. Further analysis of the data of the research results made it possible to find ways to solve these tasks, which was confirmed by the control and verification results. Conclusions. The scientific novelty of the obtained results is as follows: for the first time, the processing of closed turbine blades made in one piece with a "monowheel" type disk and obtained by the additive method with an abrasive air jet was investigated. The obtained research data were used as a basis for developing a real route technological process for processing closed-type turbine blades manufactured using the additive method.

  • Open Access

    Evaluation of the results of the flight tests of the small research rocket K80 Meteo 7000 on the way to the creation of the Ukrainian family of suborbital launch vechicles

    by Vladyslav Proroka, Mykola Dron, Oleksii Kulyk, Vadym Solntsev, Svitlana Klymenko

    The object of this research is the process of choice the strategy for the development of the Ukrainian segment of suborbital launch vehicles (SOLVs). Problems arising in this process are analyzed and a search of ways of overcoming them was carried out. The strategy of development of a family of SOLVs is based on the previous experience of developing SOLVs in other countries. A family of SOLVs is proposed which includes five rockets with the apogee from 2 to 150 kilometers. The problem of the exclusion zones which can be reserved for falling of discarded parts of vehicles during the launch was considered. Experience of other countries in overcoming this problem was analyzed. It was decided to begin the process of formulation of a concept of a simplified SOLVs control system that would ensure keeping the rocket over the area of the launch. Within this task, a choice of components of the onboard electronic equipment (OBEE) was made. For testing the OBEE in the conditions of a real flight, a K80 Meteo 7000 rocket, a member of the proposed SOLV family, was chosen. In flight tests, most of the chosen OBEE components confirmed their operability, though some showed shortcomings in their operation. Main flight parameters of the K80 Meteo 7000 rocket were demonstrated. The reach of the apogee of 6,375 m and the velocity of Mach 1.733 was confirmed. This research sets preconditions for practical implementation of launches of SOLVs with substantial altitudes of the apogee, while limiting the areas reserved for falling parts of the rockets. Availability of such SOLVs will enable solution of a wide range of problems in many fields of scientific research and the use of SOLVs as platforms for working out new technical solutions for other branches of rocketry


  • Approximation of blades of radial machines with multiparameter family of smooth surfaces

    by M Katrenko, V Borsch, O Kulyk

    Purpose. Development of a mathematical model for creating the spatial forms of blade devices of rotating radial dynamic blade machines. Methodology. An approach to the development of a mathematical model of blade profiling of radial dynamic blade machines, as parts of power plants, air-jet engines and fuel component supply systems of rocket engines, has been suggested. The approach is based on a physical model of the working body flow over helical surfaces. Findings. A system of equations for describing the blade of a radial dynamic blade machine of any purpose as a family of smooth surfaces has been obtained. A multi-parameter correction of the shape of the smooth surface of the blade, accounting for the change in geometric data, based on input and output parameters of the blade, has been developed. Based on a review of modern technology samples, possible configurations of the spatial shape of the blade of the radial and radial-axial type, geometric factors affecting the surface of the blade being created are taken into account. The possibility of obtaining a multi-level blade apparatus by changing the conditions of the geometric parameters at the entrance is shown. Originality. As part of the developed approach, in relation to the conditions for ensuring the calculated geometric parameters and the working process conditions of the blade machine, blade machines operating on compressible and non-compressible working bodies are considered. In particular, the possibility is shown of ensuring the construction of the spatial surface of the blade of the impellers of radial blade machines with a wide range of angles of the blades at the entrance and exit using smooth surfaces. Practical value. The use of a developed mathematical method allows you to perform the profile of rotating vane devices for radial vane dynamic machines of various purposes, such as centrifugal pumps and compressors, centrifugal radial turbines, as well as diagonal type vane machines. The practical significance of the obtained results is determined by the use of dynamic radial vane machines in aviation and rocket technology, aggregates of the mining industry, and technological devices of chemical industry enterprises.


  • Open Access

    AN OVERVIEW OF METHODS AND TECHNICAL MEANS OF SPACE DEBRIS REMOVAL FROM LOW EARTH ORBITS

    by А.O. Аbaturov, М.M. Dron, О.V. Kulyk, V.A. Proroka

    Debris in Earth's orbit poses a significant threat to existing spacecraft and hinders the safe launch of new spacecraft. This paper discusses various methods of space debris removal from orbit. In particular, active, passive, and combined methods are considered. The possibility of using  suborbital rockets to    launch   the    removal    system   into  orbit  is  also considered. The purpose of this paper is to review existing methods and technical means of space debris de-orbiting and analyze and identify promising areas for the development of such systems. A patent analysis was conducted for the period from 2002 to 2022. Modern scientific works on various methods of space debris removal were also analyzed. The papers on the combined method of space debris removal were analyzed separately. Non-standard approaches to space debris removal are considered. In particular, the possibility of using suborbital launch vehicles to launch removal systems into orbit is considered. As a result of the work, the current state of development of methods and technical means for space debris removal was determined. It has been found that the most commonly patented and studied in scientific papers are technical means based on the passive removal method. At the same time, the active method receives less attention in scientific papers. Because of this, it has been established that the study of passive and combined methods and the development of technical means based on these methods are promising areas. It was found that the combined method is promising, but little was studied, and the basic requirements for systems using suborbital launch vehicles were also identified. This work allowed us to summarize the current state of the problem of space debris management and identify the most promising areas for the development of space debris removal systems.


  • Open Access

    Determining energetic characteristics and selecting environmentally friendly components for solid rocket propellants at the early stages of design

    by Olena Kositsyna, Kostiantyn Varlan, Mykola Dron, Oleksii Kulyk

    This paper has investigated the possibility to theoretically calculate a value of the specific impulse for highly energetic compositions using only two parameters – the heat of the reaction and the number of moles of gaseous decomposition reaction products. Specific impulse is one of the most important energetic characteristics of rocket propellant. It demonstrates the level of achieving the value of engine thrust and propellant utilization efficiency. Determining the specific impulse experimentally is a complex task that requires meeting special conditions. For the stage of synthesis of new promising components, the comparative analysis of energetic characteristics, forecasting the value of specific impulse, especially relevant are calculation methods. Most of these methods were first developed to determine the energetic characteristics of explosives. Since explosives and rocket propellants in many cases have similar energy content and similar chemical composition, some estimation methods can be used to assess the specific impulse of solid rocket propellant. The specific impulse has been calculated for 45 compositions based on environmentally friendly oxidizers (ammonium dinitramide, hydrazinium nitroformate, hexanitrohexaazaisowurtzitane) and polymer binders polybutadiene with terminal hydroxyl groups, glycidylazide polymer, poly-3-nitratomethyl-3-methyloxetane). It was established that the estimation data obtained correlate well with literary data. Deviation of the derived values of the specific impulse from those reported in the literature is from 0.4 % to 1.8 %. The calculation results could be used for preliminary forecasting of energetic characteristics for highly energetic compositions, selecting the most promising components, as well as their ratios.


  • Вибір оптимальних методів чистової обробки лопаток закритих моноколіс турбонасосних агрегатів, отриманих адитивним методом прямого лазерного спікання порошку

    by Юрій Анатолійович Шашко, Олексій Володимирович Кулик, Роман Федосійович Максимчук, Анатолій Федорович Санін

    The creation of complex structural elements of aircraft using is promising and is widely used since such elements have several structural and technological advantages over the manufacture of parts using classical technologies. However, it requires the solution of several scientific and technical problems to obtain products of high accuracy and roughness, the development of a technological process, the development of processing modes, and sometimes the development of a new design of products. For the development of technologies in modern rocketry, improving the quality and accuracy of the production of turbines of turbopump units, an important task is to search for new and improve existing technological solutions for the manufacture of such parts with high surface quality. The work aimed to analyze the existing processing methods for parts of turbopump units with complex geometry and select the most technologically advanced one for further use in technological processes. The objective of this article is an analytical review of existing methods of surface treatment of critical parts and the selection of the most technologically advanced method for finishing the blades of a closed-type turbine (with a shroud) to reduce the roughness and improve the quality of the working surface. The object of the research is the process of machining a segment of a turbine impeller made of Inconel 718 nickel alloy (domestic analog – alloy HN45MVTJuBR), which is a key element of a turbopump unit. The blank part of the turbine monowheel type was made using 3D printing technology. As a result of the work, the optimal processing method was chosen, namely, the DryLyte dry electrochemical polishing technology, which has quite significant advantages in comparison with illogical methods. This method has been tested experimentally and is being actively implemented abroad. To introduce this DryLyte technology, it is necessary to carry out additional experiments on finishing the inner channels of small size (24 mm) using the example of interscapular channels of turbines, which will make it possible to fully assess the capabilities of the technology.

  • ОЦЕНКА ВОЗМОЖНОСТЕЙ ПРИМЕНЕНИЯ СУБОРБИТАЛЬНЫХ РАКЕТ-НОСИТЕЛЕЙ ДЛЯ ВЫВЕДЕНИЯ СРЕДСТВ УВОДА ОБЪЕКТОВ КОСМИЧЕСКОГО МУСОРА С НИЗКИХ ОКОЛОЗЕМНЫХ ОРБИТ

    by Николай Михайлович Дронь, Кирилл Валерьевич Коростюк, Александр Вячеславович Голубек, Людмила Григорьевна Дубовик, Алексей Владимирович Кулик

    The article is devoted to an actual problem of clearing of low earth orbits from space objects of a technogenic origin. Existing versions of struggle against space debris, in particular, removal of technogenic objects with help of the special means for deorbiting delivered into a target orbit by launch vehicles that are especially actual for bulky space debris are considered. Recognizing that the ascent of such means for deorbiting by orbital launch vehicles demands large financial expenses, for an increase of efficiency of delivery the means for deorbiting on a low earth orbit widely known sub-orbital launch vehicles are offered: MAXUS, TEXUS (VSB-30), REXUS (Improved Orion), SS-520, MH-300, Black Brant 12А and the estimation of a capability of their application also is conducted. Are considered the use of sub-orbital launch vehicles for the ascent the means for deorbiting on altitudes of a concentration of space debris on a low earth orbit on a trajectory, close to vertical, with the subsequent operations of interception of demanded space objects, and also modernization of launch vehicles by addition of an additional stage. Results of calculations of an injection trajectory of the means for deorbiting in weight in a layer of space debris in altitude 600 … 1200 km showed of 150 kg that sub-orbital launch vehicles MAXUS, SS-520, Black Brant 12A allow executing delivery the means for deorbiting to altitudes from 770 km to 1200 km and to supply time of its presence in a layer of space debris 420 … 850 s. The most perspective sub-orbital rocket is MAXUS. It possesses higher power and a capability of installation of an additional stage by a decrease in weight of a payload with small losses the power of the first stage. It is shown that the given configuration of the rocket with engine thrust specific impulse in vacuum 300 s and engine thrust in vacuum 16 кН is capable to inject into an elliptical orbit with an altitude of apogee 600 km and altitude of a perigee 130 km with a corner of an inclination 5,5 degrees payload in weight of 55 kg. For orbit short circuit in apogee at the altitude, the upper stage should supply 600 km increase the speeds, equal 133 m/s. Mass characteristics of the second stage are induced.