Qing Yan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Qing Yan has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Changguang Zhang
School of Civil Engineering, Chang’an University, Xi’an, China
3 shared publications - Zengzeng Zhang
School of Civil Engineering and Geomatics, Shandong University of Technology, Zibo 255000, China
3 shared publications - Junhai Zhao
School of Civil Engineering, Chang’an University, Xi’an 710061, China
2 shared publications - Tian Su
Department of Civil Engineering, School of Civil Engineering and Geomatics, Shandong University of Technology, Zibo 255000, China
2 shared publications - Fakai Dou
School of Civil Engineering and Geomatics, Shandong University of Technology, Zibo 255000, China
1 shared publication - Jianping Liu
School of Civil Engineering and Geomatics, Shandong University of Technology, Zibo 255000, China
1 shared publication
Latest Publications
- Open Access
Thermal Analysis and Thermal–Mechanical Stress Simulation of Polycrystalline Diamond Compact Bits During Rock Breaking Process
Polycrystalline diamond compact (PDC) bits are widely used in oil, gas, and geological exploration. During rock breaking, most of the work is converted into cutting heat, leading to a rise in cutter temperature and potential damage. However, the influence of formation temperature and rock properties on cutting temperature and thermal stress remains insufficiently understood. This study combined numerical simulation and experimental methods to investigate the temperature rise and thermal stress of a single PDC cutter during rock breaking, focusing on the effects of formation temperature (27–250 °C) and rock strength (sandstone, marble, and granite). The results show that the temperature rise of the PDC cutter adheres to the following three distinct stages: rapid increase, slow increase, and stabilization. Rock strength significantly affects the temperature rise rate and stress; when breaking granite, the cutter temperature reached approximately 131.4 °C, about 2–3 times higher than for marble and sandstone, while the rate of penetration (ROP) decreased by 70.6–75.6%. As formation temperature increased from 27 °C to 250 °C, the internal temperature difference within the cutter decreased from 72.6 °C to 35.6 °C, and the equivalent stress first increased and then decreased, peaking at 2.84 GPa at 50 °C. The ROP initially increased and then decreased with an increase in formation temperature. Numerical simulations and experimental findings are in good agreement. This study provides theoretical and technical guidance for optimizing cutter design and improving the rock-breaking efficiency and service life of PDC bits in deep and high-temperature formations.
Open AccessThermal Analysis and Thermal–Mechanical Stress Simulation of Polycrystalline Diamond Compact Bits During Rock Breaking Process
Polycrystalline diamond compact (PDC) bits are widely used in oil, gas, and geological exploration. During rock breaking, most of the work is converted into cutting heat, leading to a rise in cutter temperature and potential damage. However, the influence of formation temperature and rock properties on cutting temperature and thermal stress remains insufficiently understood. This study combined numerical simulation and experimental methods to investigate the temperature rise and thermal stress of a single PDC cutter during rock breaking, focusing on the effects of formation temperature (27–250 °C) and rock strength (sandstone, marble, and granite). The results show that the temperature rise of the PDC cutter adheres to the following three distinct stages: rapid increase, slow increase, and stabilization. Rock strength significantly affects the temperature rise rate and stress; when breaking granite, the cutter temperature reached approximately 131.4 °C, about 2–3 times higher than for marble and sandstone, while the rate of penetration (ROP) decreased by 70.6–75.6%. As formation temperature increased from 27 °C to 250 °C, the internal temperature difference within the cutter decreased from 72.6 °C to 35.6 °C, and the equivalent stress first increased and then decreased, peaking at 2.84 GPa at 50 °C. The ROP initially increased and then decreased with an increase in formation temperature. Numerical simulations and experimental findings are in good agreement. This study provides theoretical and technical guidance for optimizing cutter design and improving the rock-breaking efficiency and service life of PDC bits in deep and high-temperature formations.
- Open Access
Ultimate Bearing Capacity of Vertically Uniform Loaded Strip Foundations near Slopes Considering Heterogeneity, Anisotropy, and Intermediate Principal Stress Effects
Accurate prediction of the bearing capacity of foundations near slopes remains challenging when soils exhibit heterogeneity and anisotropy. Although numerical simulations can account for these effects with high precision, they are computationally demanding and provide limited physical insight. Analytical solutions that can explicitly incorporate spatial variability, directional dependence, and the influence of intermediate principal stress are still lacking. This study addresses this gap by developing an analytical solution for the ultimate bearing capacity of strip foundations near slopes based on the Unified Strength Theory (UST). The method assumes a uniformly distributed surface load and a single-sided failure mode, while introducing heterogeneity and anisotropy coefficients to represent the depth dependent and directional variation of cohesion. Validation against published theoretical, numerical, and experimental results demonstrates strong agreement, with a maximum deviation of 6.2%. Parametric sensitivity analysis indicates that increasing the heterogeneity coefficient from 0 to 1 enhances bearing capacity by 67.9–83.4%, while increasing the anisotropy coefficient from 0.6 to 1.4 reduces it by 20.8–22.3% for different base roughness. Neglecting the intermediate principal stress results in a 64.5–67.9% underestimation of the ultimate bearing capacity with different anisotropy coefficients and base roughness. The proposed analytical model based on the UST provides improved quantitative accuracy and theoretical generality, enabling safer and more economical design of foundations near slopes under heterogeneous and anisotropic soil conditions.
Open AccessUltimate Bearing Capacity of Vertically Uniform Loaded Strip Foundations near Slopes Considering Heterogeneity, Anisotropy, and Intermediate Principal Stress Effects
Accurate prediction of the bearing capacity of foundations near slopes remains challenging when soils exhibit heterogeneity and anisotropy. Although numerical simulations can account for these effects with high precision, they are computationally demanding and provide limited physical insight. Analytical solutions that can explicitly incorporate spatial variability, directional dependence, and the influence of intermediate principal stress are still lacking. This study addresses this gap by developing an analytical solution for the ultimate bearing capacity of strip foundations near slopes based on the Unified Strength Theory (UST). The method assumes a uniformly distributed surface load and a single-sided failure mode, while introducing heterogeneity and anisotropy coefficients to represent the depth dependent and directional variation of cohesion. Validation against published theoretical, numerical, and experimental results demonstrates strong agreement, with a maximum deviation of 6.2%. Parametric sensitivity analysis indicates that increasing the heterogeneity coefficient from 0 to 1 enhances bearing capacity by 67.9–83.4%, while increasing the anisotropy coefficient from 0.6 to 1.4 reduces it by 20.8–22.3% for different base roughness. Neglecting the intermediate principal stress results in a 64.5–67.9% underestimation of the ultimate bearing capacity with different anisotropy coefficients and base roughness. The proposed analytical model based on the UST provides improved quantitative accuracy and theoretical generality, enabling safer and more economical design of foundations near slopes under heterogeneous and anisotropic soil conditions.
- Open Access
Ultimate Bearing Capacity of Strip Foundations Adjacent to Heterogeneous and Anisotropic Slopes Based on the Meyerhof Theory
The soil surrounding foundations is typically heterogeneous and anisotropic; however, existing studies for estimating the ultimate bearing capacity of foundations adjacent to slopes are predominantly applicable to isotropic and homogeneous soils. This study aims to investigate the ultimate bearing capacity of strip foundations adjacent to heterogeneous and anisotropic slopes within the framework of the Meyerhof theory. Considering the soil’s heterogeneity and anisotropy, a unilateral failure mode with varying base roughness is established. An analytical solution for the ultimate bearing capacity is derived using the limit equilibrium method, and the calculation steps are outlined through an iterative trial approach. The proposed formulation is validated by comparisons with theoretical solutions, numerical simulations and experimental data. Results indicate that the ultimate bearing capacity of foundations adjacent to slopes increases with an increase in the heterogeneity coefficient. In contrast, the ultimate bearing capacity decreases as the anisotropy coefficient increases, with a more significant reduction observed for higher cohesion soil. Moreover, the base roughness and the distance to slope crest also markedly influence the ultimate bearing capacity.
Open AccessUltimate Bearing Capacity of Strip Foundations Adjacent to Heterogeneous and Anisotropic Slopes Based on the Meyerhof Theory
The soil surrounding foundations is typically heterogeneous and anisotropic; however, existing studies for estimating the ultimate bearing capacity of foundations adjacent to slopes are predominantly applicable to isotropic and homogeneous soils. This study aims to investigate the ultimate bearing capacity of strip foundations adjacent to heterogeneous and anisotropic slopes within the framework of the Meyerhof theory. Considering the soil’s heterogeneity and anisotropy, a unilateral failure mode with varying base roughness is established. An analytical solution for the ultimate bearing capacity is derived using the limit equilibrium method, and the calculation steps are outlined through an iterative trial approach. The proposed formulation is validated by comparisons with theoretical solutions, numerical simulations and experimental data. Results indicate that the ultimate bearing capacity of foundations adjacent to slopes increases with an increase in the heterogeneity coefficient. In contrast, the ultimate bearing capacity decreases as the anisotropy coefficient increases, with a more significant reduction observed for higher cohesion soil. Moreover, the base roughness and the distance to slope crest also markedly influence the ultimate bearing capacity.
- 27 October 2021
- Published by Springer Nature in Arabian Journal of Geosciences
- Vol. 14 (21) , 1-14
Ultimate bearing capacity of a strip foundation near slopes based on the unified strength theory
- 27 October 2021
- Published by Springer Nature in Arabian Journal of Geosciences
- Vol. 14 (21) , 1-14
Ultimate bearing capacity of a strip foundation near slopes based on the unified strength theory
- Open Access
- 5 April 2021
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2021, 1-10
Safety Factor of Unsaturated Soil Slopes considering the Intermediate Principal Stress Effect and Different Profiles of Matric Suction
Profiles of matric suction are critical for assessing the stability of unsaturated soil slopes, and the strength of unsaturated soils is affected by the intermediate principal stress. This study presents a theoretical formulation of safety factor for infinite unsaturated soil slopes under four different profiles of matric suction using the limit equilibrium method. The unified shear strength equation under plane strain conditions is adopted to capture the effect of intermediate principal stress on the strength of unsaturated soils. The proposed formulation of safety factor is found to have good comparability and broad applicability. The validity of the proposed formulation is demonstrated by comparing its predictions with the results of the extended shear strength method and the finite element method available in the literature. Parametric studies show that the effect of intermediate principal stress on the stability of unsaturated soil slopes is significant; the difference of safety factor among four suction profiles is pronounced, and the safety factor is highest for a linear suction profile. In addition, the safety factor changes with the infiltration depth in two stages, decreases with the slope angle, and increases with effective strength parameters. The results of this study are capable of providing beneficial guidance for optimization designs and disaster preventions of unsaturated soil slopes.
- 5 April 2021
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2021, 1-10
Open AccessSafety Factor of Unsaturated Soil Slopes considering the Intermediate Principal Stress Effect and Different Profiles of Matric Suction
Profiles of matric suction are critical for assessing the stability of unsaturated soil slopes, and the strength of unsaturated soils is affected by the intermediate principal stress. This study presents a theoretical formulation of safety factor for infinite unsaturated soil slopes under four different profiles of matric suction using the limit equilibrium method. The unified shear strength equation under plane strain conditions is adopted to capture the effect of intermediate principal stress on the strength of unsaturated soils. The proposed formulation of safety factor is found to have good comparability and broad applicability. The validity of the proposed formulation is demonstrated by comparing its predictions with the results of the extended shear strength method and the finite element method available in the literature. Parametric studies show that the effect of intermediate principal stress on the stability of unsaturated soil slopes is significant; the difference of safety factor among four suction profiles is pronounced, and the safety factor is highest for a linear suction profile. In addition, the safety factor changes with the infiltration depth in two stages, decreases with the slope angle, and increases with effective strength parameters. The results of this study are capable of providing beneficial guidance for optimization designs and disaster preventions of unsaturated soil slopes.
- Open Access
- 1 January 2020
- Published by Wiley in Advances in Civil Engineering
- Vol. 2020 (1)
Ultimate Bearing Capacity of Strip Foundations in Unsaturated Soils considering the Intermediate Principal Stress Effect
The reasonable determination of ultimate bearing capacity is crucial to an optimal design of shallow foundations. Soils surrounding shallow foundations are commonly located above the water table and are thus in an unsaturated state. The intermediate principal stress has an improving effect on the unsaturated soil strength. In this study, the ultimate bearing capacity formulation of strip foundations in unsaturated soils is presented by using Terzaghi’s theory. The unified shear strength equation of unsaturated soils under a plane strain condition is utilized to capture the intermediate principal stress effect. Furthermore, two profiles of matric suction are considered and a hyperbolic function of the friction angle related to matric suction (φb) is adopted to describe strength nonlinearity. The validity of this study is demonstrated by comparing it with model tests and a theoretical solution reported in the literature. Finally, parameter studies are conducted to investigate the effects of intermediate principal stress, matric suction, and base roughness on the ultimate bearing capacity of strip foundations. Besides, the effect of strength nonlinearity is discussed with two methods representing the angle φb.
- 1 January 2020
- Published by Wiley in Advances in Civil Engineering
- Vol. 2020 (1)
Open AccessUltimate Bearing Capacity of Strip Foundations in Unsaturated Soils considering the Intermediate Principal Stress Effect
The reasonable determination of ultimate bearing capacity is crucial to an optimal design of shallow foundations. Soils surrounding shallow foundations are commonly located above the water table and are thus in an unsaturated state. The intermediate principal stress has an improving effect on the unsaturated soil strength. In this study, the ultimate bearing capacity formulation of strip foundations in unsaturated soils is presented by using Terzaghi’s theory. The unified shear strength equation of unsaturated soils under a plane strain condition is utilized to capture the intermediate principal stress effect. Furthermore, two profiles of matric suction are considered and a hyperbolic function of the friction angle related to matric suction (φb) is adopted to describe strength nonlinearity. The validity of this study is demonstrated by comparing it with model tests and a theoretical solution reported in the literature. Finally, parameter studies are conducted to investigate the effects of intermediate principal stress, matric suction, and base roughness on the ultimate bearing capacity of strip foundations. Besides, the effect of strength nonlinearity is discussed with two methods representing the angle φb.