Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Maria Alejandra Aparicio-Ardila has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Shear Behavior of HDPE Geomembrane Interfaces with Tropical Soils

    by Henrique Rodrigues Lopes, Maria Alejandra Aparicio-Ardila, Jefferson Lins da Silva

    Understanding the mechanisms governing soil–geomembrane interface behavior is essential for defining appropriate testing conditions and obtaining reliable design parameters. This study investigates the interface shear behavior of flat-die fabricated HDPE geomembranes, focusing on the combined effects of soil type, surface texture, and support material. Smooth and textured geomembranes were tested in contact with two tropical soils: a cohesive lateritic clay and non-cohesive washed river sand. Large-scale direct shear tests were performed using a 300 mm × 300 mm apparatus under a reduced-area configuration, considering two conditions for filling the lower half-box (rigid base and soil). Results showed that, for the cohesive soil, the textured geomembrane promoted efficient interaction, with interface strength exceeding the soil’s internal strength, whereas the smooth geomembrane exhibited limited strength mobilization. In non-cohesive soil, interface strength remained lower than soil strength, even with textured surfaces. The type of support material had little influence on the behavior of the cohesive soil interface, whereas it had a significant effect on the granular soil interface. The results demonstrate that soil type governs the predominant interface interaction mechanisms, altering even the failure mode and the way shear strength is mobilized. Additionally, geomembrane surface texture enhances shear resistance by increasing interface friction and interlocking, which is particularly important in controlling soil-geomembrane interaction performance.

  • Open Access

    Textured high-density polyethylene geomembranes in geotechnical and environmental engineering: an overview

    by Maria Alejandra Aparicio-Ardila, Jefferson Lins da Silva

    Textured high-density polyethylene (HDPE) geomembranes are widely used as liners in environmental containment systems, particularly in mining facilities and sanitary landfills. Their textured surfaces enhance interface friction, improving the mechanical stability of geosynthetic barrier systems. This article presents a comprehensive review of their applications, interface behavior, and long-term performance, with emphasis on durability. Key manufacturing processes and technological advances, including conductive, Ethylene Vinyl Alcohol (EVOH), and colored layers, are discussed. Beyond manufacturing aspects, installation quality is also addressed, emphasizing that proper welding procedures, certified installers, and field quality control are essential to ensure long-term performance and minimize premature failures. Although various texturing methods are employed, the literature still lacks systematic comparative studies that isolate variables such as asperity height, which limits understanding of how manufacturing processes influence interface behavior. Furthermore, recent findings suggest that surface texturing, depending on material formulation and exposure conditions, may accelerate antioxidant depletion, potentially affecting service life. Field exposure and exhumation studies remain scarce, yet they are fundamental for validating laboratory predictions and refining design approaches. The findings highlight the need for standardized testing protocols and long-term studies tailored to the environmental conditions under which textured HDPE geomembranes are exposed. Overall, the information presented herein provides both scientific insight and practical guidance for the selection of materials and installation practices that ensure the long-term durability of geotechnical and environmental barrier systems.


  • Open Access

    Durability of Nonwoven Geotextile (PP and PET) Under Natural Weathering: A Comprehensive Evaluation Using Thermal, Mechanical, and Microstructural Analysis

    by Clever Aparecido Valentin, Jefferson Lins da Silva, Marcelo Kobelnik, Marta Pereira da Luz, Maria Alejandra Aparicio-Ardila, Gabriel Orquizas Mattielo Pedroso, Marcell Gustavo Chagas Santos

    This study evaluates the long‐term durability of two commercial nonwoven geotextiles—polypropylene (PP) and polyester (PET)—subjected to natural weathering for up to 36 months. The materials were analyzed using mechanical tests (tensile strength, puncture resistance), thermal methods (TGA, DSC, and DMA), and scanning electron microscopy (SEM) to assess degradation in their physical, mechanical, and microstructural properties. Results showed significantly higher degradation in the PP geotextile compared with PET, with up to 84% loss in tensile strength after 36 months. The PET geotextile retained more than 50% of its strength, not reaching the 50% degradation threshold within the study period. Thermal analyses confirmed changes in molecular structure, with PP showing a more pronounced loss of thermal stability. SEM images further supported these findings, revealing greater fiber damage in PP. The findings highlight the superior performance of PET geotextiles under long‐term environmental exposure, supporting their selection in applications requiring enhanced durability.

  • Open Access

    Comparative Performance Evaluation of Smooth and Textured White Geomembranes Under UV Exposure

    by Maria Alejandra Aparicio-Ardila, Jefferson Lins da Silva

    High-density polyethylene (HDPE) geomembranes are widely utilized in environmental protection projects, where they are produced in various colours to meet specific technical requirements. The addition of colour to these geomembranes involves the use of additives other than carbon black, which is traditionally employed for its cost-effectiveness and superior Ultraviolet (UV) protection properties, giving HDPE geomembranes their characteristic black colour. This study examines the degradation of smooth and textured HDPE geomembranes with a white surface. These geomembranes, with a nominal thickness of 1.00 mm, were manufactured using both flat die and round die processes and subjected to accelerated UV aging for 500 and 1000 hours, with the white surface exposed. Physical and mechanical tests were conducted to assess the performance of the geomembranes post-exposure. Initial High Load Melt Index (HLMI) and Low Load Melt Index (LLMI) values indicate differences in manufacturing processes and composition despite both geomembranes achieving similar HLMI values after 500 hours of UV exposure. The textured geomembrane exhibited a significant reduction in strain at break, likely linked to its high standard deviation, a typical characteristic of textured geomembranes. Despite these differences, both geomembranes subjected to accelerated ageing exceeded the minimum tensile property requirements specified by the GRI-GM13.


  • Natural weathering effects of nonwoven geotextile exposed to different climate conditions

    by J. L. E. Dias Filho, J. L. Silva, C. A. Valentin, M. P. Fleury, M. A. Aparicio-Ardila, D. M. Vidal, C. M. L. Costa

    Humidity, air temperature, rainfall and solar radiation all contribute to the weathering of geosynthetics. Over time, their useful life can be affected and changes in properties can be observed, which affects the performance of these materials. As geosynthetics durability analyses must encompass each work condition, assessing the climate effects is essential for design purposes. This study exposed a nonwoven needle-punched poly(ethylene) terephthalate geotextile to natural weathering in three Brazilian cities (different exogenous environments) for 18 months. Mechanical tests were conducted to evaluate the geotextile changes due to weathering. This was demonstrated by the results: exposure to weather leads to the deterioration of the geotextile mechanical properties and increased stiffness. After four months, the tensile strength fell by half, while the deformation needed more than 12 months to have this same reduction; ultraviolet radiation intensity was the most effective weathering condition in the field; humidity and rainfall can affect the stiffness of geotextiles; the impact of accumulated climate factors gradually showed a convergence in the response of geotextile to weathering. Thus, this work highlights the need to evaluate the climate conditions in each location to understand the material's behavior on the exposure time.


  • Natural weathering effects on white, green, and black HDPE textured GMs

    by M. A. Aparicio-Ardila, M. Kobelnik, C. A. Valentin, C. F. Palomino, L. P. Sabogal-Paz, J. Lins Silva

    This study investigates the degradation of textured High-Density Polyethene (HDPE) geomembranes (GMs) subjected to natural weathering for 8.5 to 10.5 years. The GMs, denoted as GM-W/B (white and black), GM-G (green) and GM-B (black), had a nominal thickness of 1.00 mm and were manufactured using a flat die process with texture on both surfaces. Standard Oxidation Induction Time (Std-OIT) tests and Thermogravimetric Analysis (TG/DTG) were performed to assess the antioxidant depletion and thermal decomposition. Additionally, degradation due to Ultraviolet (UV) radiation and environmental agents was assessed through retained physical and mechanical properties, including the Melt Flow Index (MFI) measured under various loading conditions. Antioxidant depletion and TG/DTG analyses indicated that environmental exposure compromised the thermal stability of these GMs. Among the tested GMs, GM-W/B exhibited the greatest reduction in both Std-OIT and MFI, followed by GM-G and GM-B, suggesting a direct correlation between these properties. While GM-B appeared to be still in the antioxidant depletion stage (Stage I), GM-W/B and GM-G showed signs of degradation beyond Stage I. This study provides insights into the degradation of textured HDPE GMs in the face of weathering exposure effects and the durability of colored HDPE GMs.


  • Geometric and strain behaviour of full-scale geotextile tubes for dewatering sludge

    by S. T. de Souza Paranhos, M. A. Aparicio-Ardila, J. Lins da Silva

    Geotextile tubes have been presented as a viable alternative for dewatering sludge generated in different industries, characterised by having fine grain and high moisture content. The material commonly used to develop this system is woven geotextile due to its high strength properties. However, nonwoven geotextile tubes are a possible underexplored alternative that have good cost benefits. This paper presents the geometric and strain behaviour of two full-scale nonwoven geotextile tubes used for dewatering water treatment plant (WTP) sludge. Four technologies were used to monitor the full-scale tests: ultrasonic sensor (US), perspective laser tracking (PLT), light detection and ranging (LIDAR) and draw wire sensor (DWS). The geometric parameters of a quarter of the cross-section and the strains in the geotextile were obtained during sequential fills. These data were compared with results obtained from an analytical method based on membrane theory that considers the non-linear-elastic behaviour of the geotextile. The DWS and LIDAR technologies were the most suitable for monitoring the strains and shapes of the tubes, respectively. Good agreement was found between analytical and experimental results, indicating the applicability of the adopted method to the design of the first filling cycle of the monitored nonwoven geotextile tubes.


  • Open Access

    Mechanical and Thermoanalytical Study of Polypropylene Geomats Exposed in the Field and the Laboratory

    by Jefferson Lins da Silva, Clever Aparecido Valentin, Marcelo Kobelnik, Gabriel Orquizas Mattielo Pedroso, Maria Alejandra Aparício-Ardila, Luiz Paulo Vieira de Araújo Júnior, Marta Pereira da Luz

    A Hydroelectric Power Plant (HPP) presents erosion problems on reservoir slopes and margins. Geomats are a biotechnical composite technology increasingly used to protect soils against erosion. Survivability or durability of geomats is essential for successful application. This work analyses the degradation of geomats exposed in the field for more than six years. These geomats were used as erosion-control treatment in a slope at HPP Simplício in Brazil. The degradation of the geomats in the laboratory was also analysed through exposure in a UV ageing chamber for 500 h and 1000 h. Degradation was quantitatively evaluated by testing the tensile strength of the geomat wires and thermal tests such as thermogravimetry (TG) and differential scanning calorimetry (DSC). The results showed that the geomat wires exposed in the field had a greater decrease in resistance compared to the samples exposed in the laboratory. In the samples collected in the field, it could be observed that the degradation of the virgin sample occurred earlier than in the exposed samples, contrary to what was observed in the TG tests carried out with the samples exposed in the laboratory. The DSC analysis showed that the samples had similar behaviours for the melting peaks. This evaluation of the wires of the geomats was presented as an alternative to analysing the tensile strengths of discontinuous geosynthetic materials such as the geomats.


  • Analysis of Textured Geomembrane–Soil Interface Strength to Mining Applications

    by Sergio Luiz da Costa Junior, Maria Alejandra Aparicio-Ardila, Carolina Fofonka Palomino, Jefferson Lins da Silva