Shinsuke Tanaka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Shinsuke Tanaka has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
Ken Morito
Fujitsu Laboratories Ltd., 10-1 Morinosato-Wakamiya, Atsugi, Kanagawa, 243-0197, Japan
2 shared publications- Ken Morito
Network Component PJ, Fujitsu Laboratories Ltd., Atsugi, Kanagawa Japan
2 shared publications Seok-Hwan Jeong
Fujitsu Laboratories Ltd., 10-1 Morinosato-Wakamiya, Atsugi, Kanagawa, 243-0197, Japan
2 shared publications- Shigeaki Sekiguchi
Nanotechnology Research Center, Fujitsu Laboratories Ltd., Atsugi, Kanagawa Japan
2 shared publications - Takasi Simoyama
Network Component PJ, Fujitsu Laboratories Ltd., Atsugi, Kanagawa Japan
2 shared publications - Tatsuya Usuki
Photonics Electronics Technology Research Association (PETRA)
2 shared publications
Latest Publications
- Open Access
- 3 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 39 (4) , 1148-1154
High-Speed Optical Digital-to-Analog Converter Operation of Compact Two-Segment All-Silicon Mach–Zehnder Modulator
An optical digital-to-analog converter (DAC) is a promising solution for the efficient generation of multilevel modulation signals without a high-speed electrical DAC and a large swing linear driver. We report the design and characterization of an all-Si segmented MachZehnder modulator for an optical DAC transmitter. The modulator comprises a forward-biased positive intrinsic negative (PIN) phase shifter integrated with a passive resistance and capacitance (RC) equalizer (PIN-RC) to optimize a tradeoff between modulation efficiency and analog bandwidth. We successfully confirmed an eye diagram of 90-Gbaud NRZ signal owing to a wide 3-dB bandwidth of 43.9 GHz. Additionally, a 70-Gbaud four-level pulse amplitude modulation (PAM4) waveform can be obtained via the optical DAC operation using a lumped segmented modulator because of its broad electrooptic bandwidth and uniform characteristics. A two-segmented modulator has a compact footprint of 300 m 600 m. Error-free performances based on the patterns of the PRBS11 of NRZ signals were obtained at 5070 Gbaud. The bit-error-rates of 60-Gbaud PAM4 and 70-Gbaud PAM4 were less than the 7% hard and 25.5% soft decision forward error correction limits, respectively. The optical DAC transmitter using an all-Si segmented PIN-RC modulator is suitable for next-generation high-speed multilevel modulators.
- 3 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 39 (4) , 1148-1154
Open AccessHigh-Speed Optical Digital-to-Analog Converter Operation of Compact Two-Segment All-Silicon Mach–Zehnder Modulator
An optical digital-to-analog converter (DAC) is a promising solution for the efficient generation of multilevel modulation signals without a high-speed electrical DAC and a large swing linear driver. We report the design and characterization of an all-Si segmented MachZehnder modulator for an optical DAC transmitter. The modulator comprises a forward-biased positive intrinsic negative (PIN) phase shifter integrated with a passive resistance and capacitance (RC) equalizer (PIN-RC) to optimize a tradeoff between modulation efficiency and analog bandwidth. We successfully confirmed an eye diagram of 90-Gbaud NRZ signal owing to a wide 3-dB bandwidth of 43.9 GHz. Additionally, a 70-Gbaud four-level pulse amplitude modulation (PAM4) waveform can be obtained via the optical DAC operation using a lumped segmented modulator because of its broad electrooptic bandwidth and uniform characteristics. A two-segmented modulator has a compact footprint of 300 m 600 m. Error-free performances based on the patterns of the PRBS11 of NRZ signals were obtained at 5070 Gbaud. The bit-error-rates of 60-Gbaud PAM4 and 70-Gbaud PAM4 were less than the 7% hard and 25.5% soft decision forward error correction limits, respectively. The optical DAC transmitter using an all-Si segmented PIN-RC modulator is suitable for next-generation high-speed multilevel modulators.
- 1 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (5) , 1262-1267
Low-Crosstalk Simultaneous 16-Channel × 25 Gb/s Operation of High-Density Silicon Photonics Optical Transceiver
We successfully developed a high density broadband 16-channel x 25 Gb/s on-package silicon photonics optical transceiver. The flip chip bonded bridge structure realized the high density of about 363 Gb/s/cm$^{2}$. We demonstrated the simultaneous all 16-channel error free operations with low crosstalk penalties of Tx-to-Tx 1.4 dB, Rx-to-Rx 1.4 dB, and Tx-to-Rx <0.1 dB.
- 1 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (5) , 1262-1267
Low-Crosstalk Simultaneous 16-Channel × 25 Gb/s Operation of High-Density Silicon Photonics Optical Transceiver
We successfully developed a high density broadband 16-channel x 25 Gb/s on-package silicon photonics optical transceiver. The flip chip bonded bridge structure realized the high density of about 363 Gb/s/cm$^{2}$. We demonstrated the simultaneous all 16-channel error free operations with low crosstalk penalties of Tx-to-Tx 1.4 dB, Rx-to-Rx 1.4 dB, and Tx-to-Rx <0.1 dB.
- Open Access
- 31 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (5) , 1275-1280
Ultralow-Power (1.59 mW/Gbps), 56-Gbps PAM4 Operation of Si Photonic Transmitter Integrating Segmented PIN Mach–Zehnder Modulator and 28-nm CMOS Driver
A highly-power-efficient silicon (Si) photonic PAM4 transmitter was developed by integrating a Si segmented Mach-Zehnder modulator and a CMOS driver chip. Si PIN-type phase shifters are directly driven with a CMOS inverter driver array to realize a low power operation. A passive RC equalizing technique was adopted to extend the modulation bandwidth up to 20GHz while maintaining a low power consumption. By integrating a passive RC filter within the photonics chip, we achieved a very compact foot print for the transmitter (450 $\times$ 950 mu;m). The fabricated modulator exhibited a low V $\pi$ L of 0.19 Vcm and a moderate insertion loss of 23.7 dB/cm. The transmitter successfully demonstrated clear eye-openings of PAM4 signal up to 56 Gbps together with a record-high-efficiency of 1.59 mW/Gbps. A low bit-error-rate below KP4 FEC limit (<2.0 $\times$ 10 $^{-4}$ ) was also confirmed at 50-Gbps PAM4 operation even with an un-equalized receiver.- 31 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (5) , 1275-1280
Open AccessUltralow-Power (1.59 mW/Gbps), 56-Gbps PAM4 Operation of Si Photonic Transmitter Integrating Segmented PIN Mach–Zehnder Modulator and 28-nm CMOS Driver
A highly-power-efficient silicon (Si) photonic PAM4 transmitter was developed by integrating a Si segmented Mach-Zehnder modulator and a CMOS driver chip. Si PIN-type phase shifters are directly driven with a CMOS inverter driver array to realize a low power operation. A passive RC equalizing technique was adopted to extend the modulation bandwidth up to 20GHz while maintaining a low power consumption. By integrating a passive RC filter within the photonics chip, we achieved a very compact foot print for the transmitter (450 $\times$ 950 mu;m). The fabricated modulator exhibited a low V $\pi$ L of 0.19 Vcm and a moderate insertion loss of 23.7 dB/cm. The transmitter successfully demonstrated clear eye-openings of PAM4 signal up to 56 Gbps together with a record-high-efficiency of 1.59 mW/Gbps. A low bit-error-rate below KP4 FEC limit (<2.0 $\times$ 10 $^{-4}$ ) was also confirmed at 50-Gbps PAM4 operation even with an un-equalized receiver. - Open Access
- 24 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (10) , 1959-1969
Accurate SPICE Model of Forward-Biased Silicon PIN Mach–Zehnder Modulator for an Energy-Efficient Multilevel Transmitter
A precise device model of a silicon forward-biased PIN phase shifter was developed to realize a co-design of an integrated multilevel optical transmitter combining a compact silicon-based Mach-Zehnder modulator (MZM) and a low-power CMOS driver circuit by utilizing SPICE simulation. Both electric and optical responses of the PIN phase shifter were carefully investigated at various bias conditions and temperatures in order to build a SPICE device model that precisely emulates a highly nonlinear Electric-to-Optical (EO) response of the PIN phase shifter. The validity of the developed model was assessed for a DC response, small-signal RF electric and optical responses, and also for large-signal EO responses. The simulation outputs exhibited very good agreement with the responses measured at each operation condition. Using this PIN phase shifter model, we designed a multi-level optical transmitter integrating a 750-μm long silicon PIN-based MZM with a 28-nm CMOS driver circuit via passive RC circuit equalizers. The SPICE simulation demonstrated the feasibility of the integrated transmitter for 56Gbps PAM4 operation with a very high energy efficiency : 1.2 mW/Gbps.
- 24 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (10) , 1959-1969
Open AccessAccurate SPICE Model of Forward-Biased Silicon PIN Mach–Zehnder Modulator for an Energy-Efficient Multilevel Transmitter
A precise device model of a silicon forward-biased PIN phase shifter was developed to realize a co-design of an integrated multilevel optical transmitter combining a compact silicon-based Mach-Zehnder modulator (MZM) and a low-power CMOS driver circuit by utilizing SPICE simulation. Both electric and optical responses of the PIN phase shifter were carefully investigated at various bias conditions and temperatures in order to build a SPICE device model that precisely emulates a highly nonlinear Electric-to-Optical (EO) response of the PIN phase shifter. The validity of the developed model was assessed for a DC response, small-signal RF electric and optical responses, and also for large-signal EO responses. The simulation outputs exhibited very good agreement with the responses measured at each operation condition. Using this PIN phase shifter model, we designed a multi-level optical transmitter integrating a 750-μm long silicon PIN-based MZM with a 28-nm CMOS driver circuit via passive RC circuit equalizers. The SPICE simulation demonstrated the feasibility of the integrated transmitter for 56Gbps PAM4 operation with a very high energy efficiency : 1.2 mW/Gbps.
- 4 December 2012
- Published by Optica Publishing Group in Optics Express
- Vol. 20 (27) , 28057-28069
High-output-power, single-wavelength silicon hybrid laser using precise flip-chip bonding technology
An Si/III–V hybrid laser oscillating at a single wavelength was developed for use in a large-scale Si optical I/O chip. The laser had an InP-based reflective semiconductor optical amplifier (SOA) chip integrated with an Si wavelength-selection-mirror chip in a flip-chip configuration. A low coupling loss of 1.55 dB at the Si-SOA interface was accomplished by both mode-field-matching between Si-SOA waveguides and accurately controlling the bonding position. The fabricated Si hybrid laser exhibited a very low threshold current of 9.4 mA, a high output power of 15.0 mW, and a high wall-plug efficiency of 7.6% at 20 °C. Moreover, the device maintained a high output power of >10 mW up to 60°C due to the high thermal conductance between the SOA chip and Si substrate. The short cavity length of the flip-chip bonded laser expanded the longitudinal mode spacing. This resulted in temperature-stable single longitudinal mode lasing and a low RIN level of <−130 dB/Hz.
- 4 December 2012
- Published by Optica Publishing Group in Optics Express
- Vol. 20 (27) , 28057-28069
High-output-power, single-wavelength silicon hybrid laser using precise flip-chip bonding technology
An Si/III–V hybrid laser oscillating at a single wavelength was developed for use in a large-scale Si optical I/O chip. The laser had an InP-based reflective semiconductor optical amplifier (SOA) chip integrated with an Si wavelength-selection-mirror chip in a flip-chip configuration. A low coupling loss of 1.55 dB at the Si-SOA interface was accomplished by both mode-field-matching between Si-SOA waveguides and accurately controlling the bonding position. The fabricated Si hybrid laser exhibited a very low threshold current of 9.4 mA, a high output power of 15.0 mW, and a high wall-plug efficiency of 7.6% at 20 °C. Moreover, the device maintained a high output power of >10 mW up to 60°C due to the high thermal conductance between the SOA chip and Si substrate. The short cavity length of the flip-chip bonded laser expanded the longitudinal mode spacing. This resulted in temperature-stable single longitudinal mode lasing and a low RIN level of <−130 dB/Hz.
- 1 February 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Polarization-insensitive Monolithically-integrated 8:1 SOA Gate Switch with Large Gain and High Extinction Ratio
We developed a monolithic 8:1 SOA gate switch for use in a broadband optical packet-switching system. The device exhibited a large gain of > 12.3 dB and a high extinction ratio of > 65 dB.
- 1 February 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Polarization-insensitive Monolithically-integrated 8:1 SOA Gate Switch with Large Gain and High Extinction Ratio
We developed a monolithic 8:1 SOA gate switch for use in a broadband optical packet-switching system. The device exhibited a large gain of > 12.3 dB and a high extinction ratio of > 65 dB.