SSSergey Sakhno

Sergey Sakhno

*This is an algorithmically generated author record based on publicly available information.

Sergey Sakhno has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • ВИЗНАЧЕННЯ ОСНОВНИХ ФАКТОРІВ НАДІЙНОЇ РОБОТИ ДЕТАЛЕЙ ОТРИМАНИХ МЕТОДОМ ПЛАЗМОВИХ АДИТИВНИХ ТЕХНОЛОГІЙ У СКЛАДІ АВІАЦІЙНОГО ДВИГУНА

    by Микола Миколайович Котов, Юрій Анатолійович Марченко, Сергій Сергійович Сахно, Сергій Борисович Снєсарь

    Метою роботи є аналіз та визначення основних факторів, які забезпечують надійну роботу авіаційних деталей, виготовлених методом плазмового адитивного наплавлення. Методом МПН на роботизованій установці були вирощені зразки з порошку ЭП648ВИ. На даних зразках були проведені металографічні дослідження та визначено механічні характеристики. Увага приділяється впливу таких чинників, як хімічний склад наплавленого металу, наявність дефектів, мікроструктура матеріалу, а також параметри режиму плазмового наплавлення, на експлуатаційні властивості виробів. Визначено основні чинники, що впливають на надійність роботи деталей у складі авіаційного двигуна – хімічний склад наплавленого металу; дефекти в наплавленому металі; мікроструктура наплавленого металу; параметри режиму плазмового наплавлення. Проведено комплексний аналіз факторів, які впливають на надійність роботи авіаційних деталей. Дослідження розглядає взаємозв’язок між хімічним складом наплавленого металу, наявності дефектів, мікроструктури матеріалу, а також параметрами режиму плазмового наплавлення та надійністю роботи авіаційних деталей. Це дозволяє встановити оптимальні умови для підвищення механічних властивостей деталей, зменшення дефектів та забезпечення їх довговічності в умовах експлуатації в авіаційних двигунах. Практична цінність роботи полягає в можливості підвищення надійності авіаційних деталей, виготовлених методом плазмового наплавлення, що сприяє збільшенню їх довговічності та безпечної експлуатації.

  • Open Access

    DETERMINATION OF OPTIMAL CONDITIONS FOR HERMETIC WELDING OF THIN FOILS WHEN USED IN MEMBRANE-TYPE STRUCTURES

    by К. Б. Балушок, I. Petrik I., S. Chigileychik, Y. Marchenko, S. Sakhno, І. А. Петрик, С. Л. Чигілейчик, Ю. А. Марченко

    Purpose. Development of optimal technology for welding thin-walled shells mode of 12Х18Н10Т steel (δ=0.15 mm), working at alternating loads. Research methods. Research methods. For welding automatic argon-arc welding (AAAW) equipment was used for of orbital welding, which includes a MW 2600 current source (FRONIUS) with software control unit and welding head of closed type MW40. Research warks showed that this type of welding is not enough for such small thicknesses concentration of the welding arc, which does not allow stable forming of the bath and obtaining solid uniform seam. A special robotic complex was used for microplasma welding STARWELD 190H, which includes: a power source for the regular arc INV 50; source main arc power supply INV 190; SIEMENS Simatic S 7-300 control unit; robot CR3-535M (MITSUBISHI); manipulator and HPH 80 plasmatron. Welding quality control was carried out by visual inspection and metallographic examination. Taking into account the conditions of operation of the parts, according to the technical conditions of the drawing, it was also provided pneumohydraulic control method. Obtained results. Visual inspection the outer surface of the welds showed the absence of defects in the form of pores, cracks, shells, no fusions, undercuts, etc. The geometric dimensions of the weld met the requirements of the standard documentation valid at the enterprise. Metallographic studies of the boxes membranes, welded by microplasma welding, gave a positive result. Defects of metallurgical character were not found in the welds. Practical value. The optimal method of welding that can be applied is determined for the manufacture of thin-walled membrane structures, from the point of view of manufacturability and economy expediency It has been established that microplasma welding allows obtaining a hermetically tight seam, when the thickness of parts to be welded is about 0.15 mm. The performance of welded membrane boxes is confirmed in the barostatic valve of an aircraft engine. It is established that micro plasma welding can be used in the manufacture of thin-walled shells made of 12X18H10T steel (δ=0.15 mm), which work at variable loads. The technological process of welding is introduced into the series production.


  • Open Access

    Оцінка можливості виявлення тріщин під час контролю ЛЮМ1-ОВ на лопатках турбін після нанесення комплексних жаростійких покриттів

    by Konstantin Balushok, Oleksandr Seliverstov, Oleksandr Prokopenko, Sergii Sakhno

    Currently, gas turbine engines (GTD) are being improved and made more powerful by increasing the temperature of the gases in front of the turbine and increasing the air compression ratio in the compressor. In the aviation industry, nickel heat-resistant alloys such as ЖС6У-ВІ, ЖС26-ВІ, ЖС32-ВІ, etc. are used to manufacture GTD blades. Despite their high properties in terms of corrosion resistance and heat resistance, the service life of GTD blades and their protection against oxidation and corrosion damage is ensured by applying coatings using various technologies both to the flowing surface of the blade blades (heat-resistant and heat-protective) and to the inner surfaces of the cooled channels (diffusion coatings). Failure of turbine blades is one of the most severe types of damage to turbine blades, so at different stages of serial production, including after applying heat-resistant coatings, LUM1-OV inspection of blades is performed to detect cracks that can form during processing and lead to their failure during engine operation. The paper evaluates the possibility of detecting cracks on GTD turbine blades with complex heat-resistant coatings GCP+SDP-2. The study was carried out on samples of working blades in the form of an experiment. First, fatigue tests of the samples were carried out on a test bench until cracks appeared. Then, a complex heat-resistant coating of GCP (CrAl gas circulation coating) + SDP-2 (heat-resistant alloy of the Ni-Cr-Al-Y system) was applied to the blade profile in stages according to the serial technology. After each coating was applied, the blades were inspected by the LUM1-OV method to determine the possibility of crack detection. The results showed that immediately after the application of the complex heat-resistant coating, cracks on the blades were not detected, because they spread only in the GCP layer and partially pass into the SDP-2 layer without reaching the surface. The results obtained can be the basis for removing the luminescent inspection operation from the technological process, immediately after applying complex heat-resistant coatings. Since this does not allow detecting cracks in the blade material and can lead to unnecessary costs for additional technological operations.

  • Виготовлення авіаційних деталей з жароміцних нікелевих сплавів методом адитивного плазмового наплавлення

    by Михайло Олегович Гнатенко, Сергій Леонідович Чігілейчик, Сергій Сергійович Сахно

    The aviation part of the ring-type was made of heat-resistant structural alloy EI 868 (HN60VT) by the method of additive multilayer plasma surfacing with wire. The traditional technology for obtaining this type of ring blank is the stamping of rods, which are then brought to the final shape of the part by further machining. The disadvantage of traditional technology is the significant cost of metal, which in the process of machining the pressed rod, is converted into chips and not reused, which increases the cost of the finished product. The use of additive technologies will significantly reduce the cost of material in obtaining annular workpieces by manufacturing a workpiece with a configuration as close as possible to the geometry of the part. Additive surfacing was performed on a robotic complex consisting of a plasma power supply SBI PMI-350 AC/DC TL and work FANUC M-710iC on a rigidly fixed substrate of steel 20. To determine the possibility of obtaining aviation parts using the method of layer-by-layer plasma surfacing, a study of the deposited material was conducted The structure of the grown part was studied, it was found that the microstructure corresponds to the normal state of the alloy EI868 (HN60W) in the microstructure of the fusion line is not visible, the structure is homogeneous with the mutual germination of grains between layers. Alloy parts obtained using the method of additive cultivation are at the level of cast blanks and forgings and at T = 900oC are: sв =35±5 кгс/мм2,s0,2 =49±5 кгс/мм2, y = 62±5 %. After machining the grown workpiece, a capillary method of control and radiation control of the grown part - cracks and other types of critical metallurgical defects was not detected. The practical significance of the introduction of this method is a significant reduction in material costs in obtaining parts and ensuring economic efficiency, which is about 159 thousand hryvnias.


  • Open Access

    Detecting the influence of heat sources on material properties when producing aviation parts by a direct energy deposition method

    by Mikhail Gnatenko, Pavel Zhemanyuk, Igor Petryk, Sergey Sakhno, Sergey Chigileichik, Valery Naumik, Alexander Ovchinnikov, Maria Matkovskaya

    Detecting the influence of heat sources on material properties when producing aviation parts by a direct energy deposition method