Mbulelo Ngqase
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mbulelo Ngqase has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Maje Phasha
Advanced Materials Division, Mintek, 200 Malibongwe Drive, Randburg 2125, South Africa
2 shared publications - Takalani Madzivhandila
University of Johannesburg, South Africa
2 shared publications - Willie Nheta
Mineral Processing and Technology Research Centre, University of Johannesburg, P.O. Box 17011, Doornfontein, Johannesburg 2028, South Africa
2 shared publications - Xiaowei Pan
University of Johannesburg
2 shared publications M Phasha
Mintek, Adv Mat Div, Private Bag X3015, ZA-2125 Johannesburg, South Africa
1 shared publicationT Madzivhandila
Univ Johannesburg, Fac Engn & Built Environm, POB 524, ZA-2006 Johannesburg, South Africa
1 shared publication
Latest Publications
- Open Access
Effect of Casting Shakeout Temperature on Residual Stresses of Hypoeutectic High-Chromium Iron Alloys Using the Hole-Drilling Method
In this investigation, optical emission spectrometers, a Brinell hardness tester, optical light and scanning microscopes, and X-ray diffraction were used for general metallurgical characterization of the experimental irons in as-cast states. The hole-drilling method was used to assess residual stress distributions under gross and net casting weight conditions. To create experimental irons using the casting process, raw materials were transformed from a solid to a liquid state using an industrial furnace and ladle to melt and cast, respectively. The casting shakeout temperatures for samples A and B were recorded at 60 °C and 180 °C, respectively, after a characteristic stress lattice casting component was allowed to cool for about 1645 min and 1295 min. Chemical analysis verified the experimental hypoeutectic irons of ASTM A532, Type A, Class III, 25%Cr, i.e., high chromium white cast iron alloys. Additionally, it was discovered that micrographs were made of an austenitic-martensitic matrix that contained eutectic M7C3 and secondary M23C6-type carbides. The residual stress distributions were found to be influenced by various carbide and metallic volume fraction proportions, casting section thickness, and casting shakeout duration and temperature. Optimal hardness values, however, were shown to be associated with higher residual stress distributions and an increase in major alloying elements in experimental irons. Consequently, different residual stress distributions are produced by casting shakeout temperatures at lower and higher values under gross and net casting weight conditions.
Open AccessEffect of Casting Shakeout Temperature on Residual Stresses of Hypoeutectic High-Chromium Iron Alloys Using the Hole-Drilling Method
In this investigation, optical emission spectrometers, a Brinell hardness tester, optical light and scanning microscopes, and X-ray diffraction were used for general metallurgical characterization of the experimental irons in as-cast states. The hole-drilling method was used to assess residual stress distributions under gross and net casting weight conditions. To create experimental irons using the casting process, raw materials were transformed from a solid to a liquid state using an industrial furnace and ladle to melt and cast, respectively. The casting shakeout temperatures for samples A and B were recorded at 60 °C and 180 °C, respectively, after a characteristic stress lattice casting component was allowed to cool for about 1645 min and 1295 min. Chemical analysis verified the experimental hypoeutectic irons of ASTM A532, Type A, Class III, 25%Cr, i.e., high chromium white cast iron alloys. Additionally, it was discovered that micrographs were made of an austenitic-martensitic matrix that contained eutectic M7C3 and secondary M23C6-type carbides. The residual stress distributions were found to be influenced by various carbide and metallic volume fraction proportions, casting section thickness, and casting shakeout duration and temperature. Optimal hardness values, however, were shown to be associated with higher residual stress distributions and an increase in major alloying elements in experimental irons. Consequently, different residual stress distributions are produced by casting shakeout temperatures at lower and higher values under gross and net casting weight conditions.
- Open Access
- 27 June 2025
- Published by MDPI AG in Preprints.org
Effect of Casting Shakeout Temperature on Residual Stresses of Hypoeutectic High Chromium Iron Alloys Using Hole-Drilling Method
Attention on residual stress development, magnitude, and distribution on abrasive wear materials, such as high chromium iron alloys, has been minimal, even though these materials are prone to tearing or inferior mechanical properties because of distortion during manufacturing processes, such as casting and heat treatment, leading to premature failure of cast components. Identification of the source and succeeding management of residual stress provides an opportune possibility to enhance product quality. In the current study, the as-cast hypoeutectic irons of ASTM A532, Type A, Class III, 25% Cr, i.e., sample A and sample B, were cast at 1384 and 1390 degrees Celsius and allowed to solidify and cool for approximately 1645 and 1295 minutes, respectively. Thus, the shakeout temperatures of sample A and sample B products were established to be approximately 60 and 180°C, respectively. Resultant residual stress and macrohardness were determined at ambient temperatures using the hole-drilling method and Brinell hardness tester machines, respectively. Higher hardness values of 600 BHN were established on sample B compared to 526 BHN for sample A. In addition, casting shakeout at higher temperatures, i.e., 180°C on sample B, yielded higher magnitudes of residual stress distribution compared to 60°C shakeout for sample A.
- 27 June 2025
- Published by MDPI AG in Preprints.org
Open AccessEffect of Casting Shakeout Temperature on Residual Stresses of Hypoeutectic High Chromium Iron Alloys Using Hole-Drilling Method
Attention on residual stress development, magnitude, and distribution on abrasive wear materials, such as high chromium iron alloys, has been minimal, even though these materials are prone to tearing or inferior mechanical properties because of distortion during manufacturing processes, such as casting and heat treatment, leading to premature failure of cast components. Identification of the source and succeeding management of residual stress provides an opportune possibility to enhance product quality. In the current study, the as-cast hypoeutectic irons of ASTM A532, Type A, Class III, 25% Cr, i.e., sample A and sample B, were cast at 1384 and 1390 degrees Celsius and allowed to solidify and cool for approximately 1645 and 1295 minutes, respectively. Thus, the shakeout temperatures of sample A and sample B products were established to be approximately 60 and 180°C, respectively. Resultant residual stress and macrohardness were determined at ambient temperatures using the hole-drilling method and Brinell hardness tester machines, respectively. Higher hardness values of 600 BHN were established on sample B compared to 526 BHN for sample A. In addition, casting shakeout at higher temperatures, i.e., 180°C on sample B, yielded higher magnitudes of residual stress distribution compared to 60°C shakeout for sample A.
- Open Access
- 29 October 2024
- Published by IOP Publishing in Engineering Research Express
- Vol. 6 (4) , 045414
Exploring residual stress analysis in the machining of hypoeutectic high chromium white cast iron alloys through the hole-drilling method
High chromium white cast irons (HCWCIs), ASTM A352, Type A and Class III, i.e., 25%Cr iron in as-cast condition consists of proeutectic austenite (γ-Fe), transformed martensite (α-Fe) and discontinuous Cr-rich, i.e., M7C3/ (Cr, Fe)7C3 type of carbides, which are hard and brittle in nature. Fully annealed thermal treatment was performed to improve iron’s machinability leading to fully pearlitic matrix with minor retained γ-Fe content. Eutectic (Cr, Fe)7C3 type of carbides are not affected by heat treatment processes. Resulting from corresponding manufacturing process, the magnitude and distribution of residual stresses (RSs) in as-cast and after machining were measured using hole-drilling method (HDM), as they are known to be harmful to corrosion and fatigue resistance. Furthermore, general metallurgical material characterisation was performed in as-cast and heat-treated conditions. As a result, this study revealed hardness variation, 547 and 555BHN in as-cast as compared to 327BHN in heat-treated condition. Furnace and actual cast component chemical analysis revealed a slight variation, especially between carbon (C) and chromium (Cr). Furthermore, eutectic type of carbides and precipitated secondary, i.e., (Cr, Fe)23C6 type of carbides within fully pearlitic matrix with minor amounts of retained γ-Fe were detected within the dominant matrix, i.e., pearlitic matrix in as-annealed condition. Detected magnitude and distributions of RSs on heat-treated sample resulted in higher tensile stresses in the surface and compressive in the interior as compared to sample in as-cast condition. Thus, this study was successfully in measuring RSs in as-cast and upon machining of hypoeutectic irons of HCWCI alloys using HDM.
- 29 October 2024
- Published by IOP Publishing in Engineering Research Express
- Vol. 6 (4) , 045414
Open AccessExploring residual stress analysis in the machining of hypoeutectic high chromium white cast iron alloys through the hole-drilling method
High chromium white cast irons (HCWCIs), ASTM A352, Type A and Class III, i.e., 25%Cr iron in as-cast condition consists of proeutectic austenite (γ-Fe), transformed martensite (α-Fe) and discontinuous Cr-rich, i.e., M7C3/ (Cr, Fe)7C3 type of carbides, which are hard and brittle in nature. Fully annealed thermal treatment was performed to improve iron’s machinability leading to fully pearlitic matrix with minor retained γ-Fe content. Eutectic (Cr, Fe)7C3 type of carbides are not affected by heat treatment processes. Resulting from corresponding manufacturing process, the magnitude and distribution of residual stresses (RSs) in as-cast and after machining were measured using hole-drilling method (HDM), as they are known to be harmful to corrosion and fatigue resistance. Furthermore, general metallurgical material characterisation was performed in as-cast and heat-treated conditions. As a result, this study revealed hardness variation, 547 and 555BHN in as-cast as compared to 327BHN in heat-treated condition. Furnace and actual cast component chemical analysis revealed a slight variation, especially between carbon (C) and chromium (Cr). Furthermore, eutectic type of carbides and precipitated secondary, i.e., (Cr, Fe)23C6 type of carbides within fully pearlitic matrix with minor amounts of retained γ-Fe were detected within the dominant matrix, i.e., pearlitic matrix in as-annealed condition. Detected magnitude and distributions of RSs on heat-treated sample resulted in higher tensile stresses in the surface and compressive in the interior as compared to sample in as-cast condition. Thus, this study was successfully in measuring RSs in as-cast and upon machining of hypoeutectic irons of HCWCI alloys using HDM.
- Open Access
- 1 March 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1495 (1) , 012023
An Overview on Types of White Cast Irons and High Chromium White Cast Irons
Crushing and grinding are widely used in mining, mineral processing, cement making, and coal power generation. The mechanical components that contact with materials being processed are working under the conditions of high abrasion and impact. How to reduce the wearing damages and prevent from the cracking failure of the mechanical parts is one of the crucial challenges facing the operations of many industries, involved crushing and grinding processes. Whit cast irons, and specifically high chromium white cast irons, have been developed and deployed worldwide for making mechanical components of crushing and grinding machines due to the combination of high wear resistance and good mechanical strength. The paper is aimed to give an overview on the white cast iron alloys, and particularly high chromium white cast iron alloys, including their classifications, their standard specifications in USA, China and Australia, their main usages and the new developments.
- 1 March 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1495 (1) , 012023
Open AccessAn Overview on Types of White Cast Irons and High Chromium White Cast Irons
Crushing and grinding are widely used in mining, mineral processing, cement making, and coal power generation. The mechanical components that contact with materials being processed are working under the conditions of high abrasion and impact. How to reduce the wearing damages and prevent from the cracking failure of the mechanical parts is one of the crucial challenges facing the operations of many industries, involved crushing and grinding processes. Whit cast irons, and specifically high chromium white cast irons, have been developed and deployed worldwide for making mechanical components of crushing and grinding machines due to the combination of high wear resistance and good mechanical strength. The paper is aimed to give an overview on the white cast iron alloys, and particularly high chromium white cast iron alloys, including their classifications, their standard specifications in USA, China and Australia, their main usages and the new developments.
- Open Access
- 1 March 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1495 (1) , 012024
Microstructural Investigation on Heat Treatment of Hypoeutectic High Chromium White Cast Irons
High chromium white cast irons (HCWCI) are widely used as abrasion resistant materials in cement manufacturing, mineral processing and slurry pumping industries. Their high resistance to wear in these demanding situations stems from the presence of hard eutectic (Cr, Fe)7C3 carbides in their microstructures. In this context, the properties of hypoeutectic iron of HCWCI containing 25 wt. %Cr-2.5 wt. %C were investigated after destabilisation heat treatments, cooling (slow and fast cooling) to ambient temperatures, their influence on the microstructure was investigated. For characterization of the hypoeutectic iron of HCWCI, several experimental tests were performed using the following laboratory equipment: light optical microscope, scanning electron microscope. The amount of retained austenite also depends on the alloying additions in the melt during melting processes, destabilisation temperatures, soaking time and the cooling rates during heat treatment processes.
- 1 March 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1495 (1) , 012024
Open AccessMicrostructural Investigation on Heat Treatment of Hypoeutectic High Chromium White Cast Irons
High chromium white cast irons (HCWCI) are widely used as abrasion resistant materials in cement manufacturing, mineral processing and slurry pumping industries. Their high resistance to wear in these demanding situations stems from the presence of hard eutectic (Cr, Fe)7C3 carbides in their microstructures. In this context, the properties of hypoeutectic iron of HCWCI containing 25 wt. %Cr-2.5 wt. %C were investigated after destabilisation heat treatments, cooling (slow and fast cooling) to ambient temperatures, their influence on the microstructure was investigated. For characterization of the hypoeutectic iron of HCWCI, several experimental tests were performed using the following laboratory equipment: light optical microscope, scanning electron microscope. The amount of retained austenite also depends on the alloying additions in the melt during melting processes, destabilisation temperatures, soaking time and the cooling rates during heat treatment processes.