Gürkan Kaya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gürkan Kaya has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
Fatih Yıldız
10 shared publications- Tevfik Oğuzhan Ergüder
KAFKAS ÜNİVERSİTESİ, MÜHENDİSLİK-MİMARLIK FAKÜLTESİ, MAKİNE MÜHENDİSLİĞİ BÖLÜMÜ
5 shared publications - Yusuf Polat
Erzurum Technical University
4 shared publications - Elanur Çelebi Kavdir
ERZURUM TEKNİK ÜNİVERSİTESİ, MÜHENDİSLİK VE MİMARLIK FAKÜLTESİ, MAKİNE MÜHENDİSLİĞİ BÖLÜMÜ
3 shared publications Ali Fatih Yetim
Department of Mechanical Engineering, Erzurum Technical University, Erzurum, Turkey
2 shared publications- Emre Mandev
Department of Mechanical Engineering, Erzurum Technical University, Erzurum, Turkey
2 shared publications
Latest Publications
- Open Access
Cooling-Regime Effects on the Residual Mechanical Properties, Hardness and Fracture Characteristics of Fire-Exposed Hardox Abrasion-Resistant Steels
This study examines how cooling history affects the residual properties of 4-mm-thick Hardox 450 and Hardox 500 Tuf abrasion-resistant steels after thermal exposure. The programme includes an unheated reference at 23 °C and exposures to 300, 400, 500, 600, 800 and 1000 °C, followed by air cooling (AC), water spray cooling (WSC) or blanket cooling (BC). Room-temperature tensile tests and Vickers microhardness measurements characterize the residual response; X-ray diffraction (XRD) and scanning electron microscopy (SEM) examine the reference and 800 °C conditions. Each hardness value represents the mean of five indentations. Both grades retain most of their reference ultimate tensile strength at 300 °C, whereas strength loss becomes pronounced at 500–600 °C. After 1000 °C exposure, WSC specimens retain approximately 52.5% and 79% of the reference ultimate tensile strength for Hardox 450 and Hardox 500 Tuf, respectively, with strains at maximum stress of 3.50% and 3.79%. Local post-tensile hardness remains substantially below the reference level. The results therefore show that recovery of tensile strength does not establish restoration of the original property balance. XRD and fractography support qualitative interpretation at 800 °C but do not verify the transformation mechanism at 1000 °C. Continuous piecewise linear equations describe the measured trends within the investigated conditions; their predictive accuracy and between-specimen variability remain unestablished.
Open AccessCooling-Regime Effects on the Residual Mechanical Properties, Hardness and Fracture Characteristics of Fire-Exposed Hardox Abrasion-Resistant Steels
This study examines how cooling history affects the residual properties of 4-mm-thick Hardox 450 and Hardox 500 Tuf abrasion-resistant steels after thermal exposure. The programme includes an unheated reference at 23 °C and exposures to 300, 400, 500, 600, 800 and 1000 °C, followed by air cooling (AC), water spray cooling (WSC) or blanket cooling (BC). Room-temperature tensile tests and Vickers microhardness measurements characterize the residual response; X-ray diffraction (XRD) and scanning electron microscopy (SEM) examine the reference and 800 °C conditions. Each hardness value represents the mean of five indentations. Both grades retain most of their reference ultimate tensile strength at 300 °C, whereas strength loss becomes pronounced at 500–600 °C. After 1000 °C exposure, WSC specimens retain approximately 52.5% and 79% of the reference ultimate tensile strength for Hardox 450 and Hardox 500 Tuf, respectively, with strains at maximum stress of 3.50% and 3.79%. Local post-tensile hardness remains substantially below the reference level. The results therefore show that recovery of tensile strength does not establish restoration of the original property balance. XRD and fractography support qualitative interpretation at 800 °C but do not verify the transformation mechanism at 1000 °C. Continuous piecewise linear equations describe the measured trends within the investigated conditions; their predictive accuracy and between-specimen variability remain unestablished.
- 31 July 2026
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 28 (2) , 738-748
Effect of fiber orientation and stress level on creep behavior of glass fiber reinforced epoxy composites
Glass fiber reinforced polymer (GFRP) composites, made of glass fiber and plastic, are widely used in structural applications because of their high strength and resistance to corrosion. But the orientation of the fibers and the level of stress have a major effect on their performance characteristics when subjected to constant stress. This paper experimentally investigates the flexural and flexural creep behavior of glass fiber-reinforced epoxy composites with varying fiber orientations. Composite laminates were made using the vacuum-assisted resin transfer molding (VARTM) process. The specimens with fiber orientations of 0°, 30°, 45°, and 60° were prepared and tested. Initially, static three-point bending tests were conducted to determine the ultimate flexural strength values. Creep tests were conducted at stress levels of 25%, 50%, and 75% of the maximum flexural strength for 120 minutes, based on these values. The results showed that the fiber orientation significantly affected both flexural strength and creep response. The specimens with a 0° fiber orientation showed the highest flexural strength as 133.1 ± 17.8 MPa and the lowest creep deformations which are 0.78 mm, 1.48 mm, and 2.69 mm for 25%, 50%, and 75% stress levels, respectively after two hours. On the contrary, the 45° fiber orientation showed the lowest strength as 63.2 ± 8.9 MPa and hence highest creep deformations which are 1.01 mm, 2.53 mm, and nearly 10 mm for 25%, 50%, and 75% stress levels, respectively. The 45° fiber-oriented sample was failed after nearly 2000 seconds which could not reach the two hours under 75% stress level. With an increase in the fiber orientation angle, the stiffness reduced and the displacement increased due to the dominance of matrix-dominated deformation mechanisms. As stress levels rose, the impact of fiber orientation intensified, leading to unstable creep behavior, especially in 45° specimens at a 75% stress level. The findings demonstrate that both fiber orientation and applied stress level must be considered in the design of GFRP components subjected to long-term loading conditions.
- 31 July 2026
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 28 (2) , 738-748
Effect of fiber orientation and stress level on creep behavior of glass fiber reinforced epoxy composites
Glass fiber reinforced polymer (GFRP) composites, made of glass fiber and plastic, are widely used in structural applications because of their high strength and resistance to corrosion. But the orientation of the fibers and the level of stress have a major effect on their performance characteristics when subjected to constant stress. This paper experimentally investigates the flexural and flexural creep behavior of glass fiber-reinforced epoxy composites with varying fiber orientations. Composite laminates were made using the vacuum-assisted resin transfer molding (VARTM) process. The specimens with fiber orientations of 0°, 30°, 45°, and 60° were prepared and tested. Initially, static three-point bending tests were conducted to determine the ultimate flexural strength values. Creep tests were conducted at stress levels of 25%, 50%, and 75% of the maximum flexural strength for 120 minutes, based on these values. The results showed that the fiber orientation significantly affected both flexural strength and creep response. The specimens with a 0° fiber orientation showed the highest flexural strength as 133.1 ± 17.8 MPa and the lowest creep deformations which are 0.78 mm, 1.48 mm, and 2.69 mm for 25%, 50%, and 75% stress levels, respectively after two hours. On the contrary, the 45° fiber orientation showed the lowest strength as 63.2 ± 8.9 MPa and hence highest creep deformations which are 1.01 mm, 2.53 mm, and nearly 10 mm for 25%, 50%, and 75% stress levels, respectively. The 45° fiber-oriented sample was failed after nearly 2000 seconds which could not reach the two hours under 75% stress level. With an increase in the fiber orientation angle, the stiffness reduced and the displacement increased due to the dominance of matrix-dominated deformation mechanisms. As stress levels rose, the impact of fiber orientation intensified, leading to unstable creep behavior, especially in 45° specimens at a 75% stress level. The findings demonstrate that both fiber orientation and applied stress level must be considered in the design of GFRP components subjected to long-term loading conditions.
- 30 July 2026
- Published by Journal of Innovative Engineering and Natural Science in Journal of Innovative Engineering and Natural Science
- Vol. 6 (2) , 551-562
DIC controlled tensile creep behavior of glass fiber reinforced epoxy composites
This study aims to investigation of digital image correlation (DIC) technique application to measure the time-dependent strain distribution under creep behavior of glass fiber reinforced polymer (GFRP) composites. A plain-woven glass fiber fabric reinforced epoxy was produced and creep behavior were characterized by considering the effects of fiber orientation. First, the 0°, 30°, 45°, and 60° oriented samples were tested under tensile loading conditions to see the force – displacement behavior of GFRP. Then, same geometry of samples was used to test creep behavior under tensile conditions. The 50% of the ultimate stress for each fiber orientation was set for the creep test. The DIC technique is used to measure the creep strain at various loads at room temperature. The DIC application for creating strain maps showed that the fiber orientation has significant effect on creep, especially for 45°sample due to shear-based deformation. Overall, the DIC technique presented accurate and practical results on time dependent strain behavior of GFRP composites under constant load.
- 30 July 2026
- Published by Journal of Innovative Engineering and Natural Science in Journal of Innovative Engineering and Natural Science
- Vol. 6 (2) , 551-562
DIC controlled tensile creep behavior of glass fiber reinforced epoxy composites
This study aims to investigation of digital image correlation (DIC) technique application to measure the time-dependent strain distribution under creep behavior of glass fiber reinforced polymer (GFRP) composites. A plain-woven glass fiber fabric reinforced epoxy was produced and creep behavior were characterized by considering the effects of fiber orientation. First, the 0°, 30°, 45°, and 60° oriented samples were tested under tensile loading conditions to see the force – displacement behavior of GFRP. Then, same geometry of samples was used to test creep behavior under tensile conditions. The 50% of the ultimate stress for each fiber orientation was set for the creep test. The DIC technique is used to measure the creep strain at various loads at room temperature. The DIC application for creating strain maps showed that the fiber orientation has significant effect on creep, especially for 45°sample due to shear-based deformation. Overall, the DIC technique presented accurate and practical results on time dependent strain behavior of GFRP composites under constant load.
- Open Access
- 15 March 2026
- Published by Tulpar Academic Publishing in Challenge Journal of Structural Mechanics
- Vol. 12 (1) , 45
Investigating Iosipescu shear properties of laser powder bed fusion 316L stainless steel via digital image correlation technique
Laser Powder Bed Fusion (LPBF) has been widely adopted for producing stainless steel 316L components with complex geometries; however, despite extensive research on its tensile performance, the shear behavior of LPBF 316L remains insufficiently characterized. Reliable shear properties are crucial for structural components operating under multiaxial loading, yet experimental data enabling accurate calibration of multiaxial yield and failure models are still scarce. In this study, the tensile and shear responses of LPBF 316L were systematically investigated through standard uniaxial tensile testing and Iosipescu shear testing, supported by full-field Digital Image Correlation (DIC). All specimens were fabricated using LPBF system, and their build orientations were precisely documented to account for anisotropy effects. Tensile tests yielded an ultimate tensile strength of approximately 650 MPa and an average elastic modulus of 197 ± 32 GPa. Iosipescu shear tests demonstrated a maximum shear stress of 621 MPa, revealing a notably close relationship between shear strength and tensile strength. The experimentally measured shear modulus was also consistent with the tensile-derived value through classical elastic relations. The combined results deepen our understanding of LPBF 316L mechanical behavior, especially the coupling between tensile and shear responses. The findings further highlight the importance of integrating shear data into design procedures, multiaxial stress assessments, and material databases for additively manufactured stainless steels. Overall, this study provides a robust experimental foundation for improving structural integrity assessments and advancing the design of LPBF 316L components subjected to complex loading.
- 15 March 2026
- Published by Tulpar Academic Publishing in Challenge Journal of Structural Mechanics
- Vol. 12 (1) , 45
Open AccessInvestigating Iosipescu shear properties of laser powder bed fusion 316L stainless steel via digital image correlation technique
Laser Powder Bed Fusion (LPBF) has been widely adopted for producing stainless steel 316L components with complex geometries; however, despite extensive research on its tensile performance, the shear behavior of LPBF 316L remains insufficiently characterized. Reliable shear properties are crucial for structural components operating under multiaxial loading, yet experimental data enabling accurate calibration of multiaxial yield and failure models are still scarce. In this study, the tensile and shear responses of LPBF 316L were systematically investigated through standard uniaxial tensile testing and Iosipescu shear testing, supported by full-field Digital Image Correlation (DIC). All specimens were fabricated using LPBF system, and their build orientations were precisely documented to account for anisotropy effects. Tensile tests yielded an ultimate tensile strength of approximately 650 MPa and an average elastic modulus of 197 ± 32 GPa. Iosipescu shear tests demonstrated a maximum shear stress of 621 MPa, revealing a notably close relationship between shear strength and tensile strength. The experimentally measured shear modulus was also consistent with the tensile-derived value through classical elastic relations. The combined results deepen our understanding of LPBF 316L mechanical behavior, especially the coupling between tensile and shear responses. The findings further highlight the importance of integrating shear data into design procedures, multiaxial stress assessments, and material databases for additively manufactured stainless steels. Overall, this study provides a robust experimental foundation for improving structural integrity assessments and advancing the design of LPBF 316L components subjected to complex loading.
- 30 September 2025
- Published by Bitlis Eren Universitesi Fen Bilimleri Dergisi in Bitlis Eren Üniversitesi Fen Bilimleri Dergisi
- Vol. 14 (3) , 1759-1771
Effect of Build Orientation and Heat Treatment on Shear Strength of Additively Manufactured Ti6Al4V Alloy
This study investigates the effects of build orientation and heat treatment on the transverse shear properties of additively manufactured Ti6Al4V alloy produced by laser powder bed fusion (LPBF). Specimens were fabricated in three different build orientations (0°, 45°, and 90°) and subjected to heat treatment at 900 °C under argon gas atmosphere. Transverse shear strength was evaluated using the short beam shear test method. The results revealed that build orientation significantly affects both shear strength and ductility of materials. Compared to the 0° reference, the 45° and 90° samples showed an approximately 43% increase in shear strength, along with 56% and 103% increases in displacement, respectively. Heat treatment further enhanced the ductility, especially for the 45° oriented specimen, which exhibited the highest displacement and a 26% increase in shear strength compared with reference 0° sample. However, heat treatment slightly reduced the strength of the 45° and 90° specimens relative to their untreated counterparts. Fractographic analysis confirmed quasi-brittle failure with the presence of dimples, indicating enhanced ductility post-heat treatment. These findings provide novel insight into optimizing process parameters and post-processing strategies to improve the shear performance of LPBF Ti6Al4V components for critical structural applications.
- 30 September 2025
- Published by Bitlis Eren Universitesi Fen Bilimleri Dergisi in Bitlis Eren Üniversitesi Fen Bilimleri Dergisi
- Vol. 14 (3) , 1759-1771
Effect of Build Orientation and Heat Treatment on Shear Strength of Additively Manufactured Ti6Al4V Alloy
This study investigates the effects of build orientation and heat treatment on the transverse shear properties of additively manufactured Ti6Al4V alloy produced by laser powder bed fusion (LPBF). Specimens were fabricated in three different build orientations (0°, 45°, and 90°) and subjected to heat treatment at 900 °C under argon gas atmosphere. Transverse shear strength was evaluated using the short beam shear test method. The results revealed that build orientation significantly affects both shear strength and ductility of materials. Compared to the 0° reference, the 45° and 90° samples showed an approximately 43% increase in shear strength, along with 56% and 103% increases in displacement, respectively. Heat treatment further enhanced the ductility, especially for the 45° oriented specimen, which exhibited the highest displacement and a 26% increase in shear strength compared with reference 0° sample. However, heat treatment slightly reduced the strength of the 45° and 90° specimens relative to their untreated counterparts. Fractographic analysis confirmed quasi-brittle failure with the presence of dimples, indicating enhanced ductility post-heat treatment. These findings provide novel insight into optimizing process parameters and post-processing strategies to improve the shear performance of LPBF Ti6Al4V components for critical structural applications.