Elanur Çelebi Kavdir
Research Subjects
Elanur Çelebi Kavdir has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Gürkan Kaya
Department of Mechanical Engineering, Erzurum Technical University, Erzurum, Turkey
3 shared publications - Yusuf Polat
Erzurum Technical University
3 shared publications Murat Demir Aydin
Erzurum Technical University
1 shared publication
Latest Publications
- 31 July 2026
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 28 (2) , 738-748
Effect of fiber orientation and stress level on creep behavior of glass fiber reinforced epoxy composites
Glass fiber reinforced polymer (GFRP) composites, made of glass fiber and plastic, are widely used in structural applications because of their high strength and resistance to corrosion. But the orientation of the fibers and the level of stress have a major effect on their performance characteristics when subjected to constant stress. This paper experimentally investigates the flexural and flexural creep behavior of glass fiber-reinforced epoxy composites with varying fiber orientations. Composite laminates were made using the vacuum-assisted resin transfer molding (VARTM) process. The specimens with fiber orientations of 0°, 30°, 45°, and 60° were prepared and tested. Initially, static three-point bending tests were conducted to determine the ultimate flexural strength values. Creep tests were conducted at stress levels of 25%, 50%, and 75% of the maximum flexural strength for 120 minutes, based on these values. The results showed that the fiber orientation significantly affected both flexural strength and creep response. The specimens with a 0° fiber orientation showed the highest flexural strength as 133.1 ± 17.8 MPa and the lowest creep deformations which are 0.78 mm, 1.48 mm, and 2.69 mm for 25%, 50%, and 75% stress levels, respectively after two hours. On the contrary, the 45° fiber orientation showed the lowest strength as 63.2 ± 8.9 MPa and hence highest creep deformations which are 1.01 mm, 2.53 mm, and nearly 10 mm for 25%, 50%, and 75% stress levels, respectively. The 45° fiber-oriented sample was failed after nearly 2000 seconds which could not reach the two hours under 75% stress level. With an increase in the fiber orientation angle, the stiffness reduced and the displacement increased due to the dominance of matrix-dominated deformation mechanisms. As stress levels rose, the impact of fiber orientation intensified, leading to unstable creep behavior, especially in 45° specimens at a 75% stress level. The findings demonstrate that both fiber orientation and applied stress level must be considered in the design of GFRP components subjected to long-term loading conditions.
- 31 July 2026
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 28 (2) , 738-748
Effect of fiber orientation and stress level on creep behavior of glass fiber reinforced epoxy composites
Glass fiber reinforced polymer (GFRP) composites, made of glass fiber and plastic, are widely used in structural applications because of their high strength and resistance to corrosion. But the orientation of the fibers and the level of stress have a major effect on their performance characteristics when subjected to constant stress. This paper experimentally investigates the flexural and flexural creep behavior of glass fiber-reinforced epoxy composites with varying fiber orientations. Composite laminates were made using the vacuum-assisted resin transfer molding (VARTM) process. The specimens with fiber orientations of 0°, 30°, 45°, and 60° were prepared and tested. Initially, static three-point bending tests were conducted to determine the ultimate flexural strength values. Creep tests were conducted at stress levels of 25%, 50%, and 75% of the maximum flexural strength for 120 minutes, based on these values. The results showed that the fiber orientation significantly affected both flexural strength and creep response. The specimens with a 0° fiber orientation showed the highest flexural strength as 133.1 ± 17.8 MPa and the lowest creep deformations which are 0.78 mm, 1.48 mm, and 2.69 mm for 25%, 50%, and 75% stress levels, respectively after two hours. On the contrary, the 45° fiber orientation showed the lowest strength as 63.2 ± 8.9 MPa and hence highest creep deformations which are 1.01 mm, 2.53 mm, and nearly 10 mm for 25%, 50%, and 75% stress levels, respectively. The 45° fiber-oriented sample was failed after nearly 2000 seconds which could not reach the two hours under 75% stress level. With an increase in the fiber orientation angle, the stiffness reduced and the displacement increased due to the dominance of matrix-dominated deformation mechanisms. As stress levels rose, the impact of fiber orientation intensified, leading to unstable creep behavior, especially in 45° specimens at a 75% stress level. The findings demonstrate that both fiber orientation and applied stress level must be considered in the design of GFRP components subjected to long-term loading conditions.
- 30 July 2026
- Published by Journal of Innovative Engineering and Natural Science in Journal of Innovative Engineering and Natural Science
- Vol. 6 (2) , 551-562
DIC controlled tensile creep behavior of glass fiber reinforced epoxy composites
This study aims to investigation of digital image correlation (DIC) technique application to measure the time-dependent strain distribution under creep behavior of glass fiber reinforced polymer (GFRP) composites. A plain-woven glass fiber fabric reinforced epoxy was produced and creep behavior were characterized by considering the effects of fiber orientation. First, the 0°, 30°, 45°, and 60° oriented samples were tested under tensile loading conditions to see the force – displacement behavior of GFRP. Then, same geometry of samples was used to test creep behavior under tensile conditions. The 50% of the ultimate stress for each fiber orientation was set for the creep test. The DIC technique is used to measure the creep strain at various loads at room temperature. The DIC application for creating strain maps showed that the fiber orientation has significant effect on creep, especially for 45°sample due to shear-based deformation. Overall, the DIC technique presented accurate and practical results on time dependent strain behavior of GFRP composites under constant load.
- 30 July 2026
- Published by Journal of Innovative Engineering and Natural Science in Journal of Innovative Engineering and Natural Science
- Vol. 6 (2) , 551-562
DIC controlled tensile creep behavior of glass fiber reinforced epoxy composites
This study aims to investigation of digital image correlation (DIC) technique application to measure the time-dependent strain distribution under creep behavior of glass fiber reinforced polymer (GFRP) composites. A plain-woven glass fiber fabric reinforced epoxy was produced and creep behavior were characterized by considering the effects of fiber orientation. First, the 0°, 30°, 45°, and 60° oriented samples were tested under tensile loading conditions to see the force – displacement behavior of GFRP. Then, same geometry of samples was used to test creep behavior under tensile conditions. The 50% of the ultimate stress for each fiber orientation was set for the creep test. The DIC technique is used to measure the creep strain at various loads at room temperature. The DIC application for creating strain maps showed that the fiber orientation has significant effect on creep, especially for 45°sample due to shear-based deformation. Overall, the DIC technique presented accurate and practical results on time dependent strain behavior of GFRP composites under constant load.
- Open Access
- 15 March 2026
- Published by Tulpar Academic Publishing in Challenge Journal of Structural Mechanics
- Vol. 12 (1) , 45
Investigating Iosipescu shear properties of laser powder bed fusion 316L stainless steel via digital image correlation technique
Laser Powder Bed Fusion (LPBF) has been widely adopted for producing stainless steel 316L components with complex geometries; however, despite extensive research on its tensile performance, the shear behavior of LPBF 316L remains insufficiently characterized. Reliable shear properties are crucial for structural components operating under multiaxial loading, yet experimental data enabling accurate calibration of multiaxial yield and failure models are still scarce. In this study, the tensile and shear responses of LPBF 316L were systematically investigated through standard uniaxial tensile testing and Iosipescu shear testing, supported by full-field Digital Image Correlation (DIC). All specimens were fabricated using LPBF system, and their build orientations were precisely documented to account for anisotropy effects. Tensile tests yielded an ultimate tensile strength of approximately 650 MPa and an average elastic modulus of 197 ± 32 GPa. Iosipescu shear tests demonstrated a maximum shear stress of 621 MPa, revealing a notably close relationship between shear strength and tensile strength. The experimentally measured shear modulus was also consistent with the tensile-derived value through classical elastic relations. The combined results deepen our understanding of LPBF 316L mechanical behavior, especially the coupling between tensile and shear responses. The findings further highlight the importance of integrating shear data into design procedures, multiaxial stress assessments, and material databases for additively manufactured stainless steels. Overall, this study provides a robust experimental foundation for improving structural integrity assessments and advancing the design of LPBF 316L components subjected to complex loading.
- 15 March 2026
- Published by Tulpar Academic Publishing in Challenge Journal of Structural Mechanics
- Vol. 12 (1) , 45
Open AccessInvestigating Iosipescu shear properties of laser powder bed fusion 316L stainless steel via digital image correlation technique
Laser Powder Bed Fusion (LPBF) has been widely adopted for producing stainless steel 316L components with complex geometries; however, despite extensive research on its tensile performance, the shear behavior of LPBF 316L remains insufficiently characterized. Reliable shear properties are crucial for structural components operating under multiaxial loading, yet experimental data enabling accurate calibration of multiaxial yield and failure models are still scarce. In this study, the tensile and shear responses of LPBF 316L were systematically investigated through standard uniaxial tensile testing and Iosipescu shear testing, supported by full-field Digital Image Correlation (DIC). All specimens were fabricated using LPBF system, and their build orientations were precisely documented to account for anisotropy effects. Tensile tests yielded an ultimate tensile strength of approximately 650 MPa and an average elastic modulus of 197 ± 32 GPa. Iosipescu shear tests demonstrated a maximum shear stress of 621 MPa, revealing a notably close relationship between shear strength and tensile strength. The experimentally measured shear modulus was also consistent with the tensile-derived value through classical elastic relations. The combined results deepen our understanding of LPBF 316L mechanical behavior, especially the coupling between tensile and shear responses. The findings further highlight the importance of integrating shear data into design procedures, multiaxial stress assessments, and material databases for additively manufactured stainless steels. Overall, this study provides a robust experimental foundation for improving structural integrity assessments and advancing the design of LPBF 316L components subjected to complex loading.
- 30 March 2020
- Published by Yildiz Technical University in Journal of Thermal Engineering
- Vol. 6 (2) , 170-179
THE STRESS ANALYSIS ON TWO DIFFERENT ADHESIVELY BONDED T-JOINTS VIA 3D NONLINEAR FINITE ELEMENT METHOD
Adhesively bonded joints are formed in different configurations. T- adhesively bonded joint is one of these configurations and has an important position in industrial applications. The purpose of this study was to numerically study the stress distributions, strength, damage evolution of different T-joints with or without adhesive filling at the curvature of the L-shaped adherends under tensile load via 3D nonlinear finite element method. Here, type-I T-joint is the first model without adhesive filling at the curvature of the L-shaped adherends and type-II T-joint is the second model with adhesive filling at the curvature of the L-shaped adherends. In this study, FM73 and 3M 2214 adhesives and AA2024-T3 aluminum alloy adherends have been used to create two different T-joints numerically. Numerical analysis results have shown that the presence of filler adhesive has a direct influence on joint strength. It has also been observed that ABCD interface is the most critical region in terms of damage occurrence, while is AB and BC lines on the ABCD interface are the most critical lines. In addition, it was observed upon comparing the stress distributions of lines AB and BC that the shear and normal stress values decreased in lines AB and BC of the type-II T-joints. Therefore, it can be put forth that the strength of Type-II T-joints is greater in comparison with the strength of type-I T-joints and the use of a type-II T-joints is more suitable for loads which are close to the fracture load of the T-joints.
- 30 March 2020
- Published by Yildiz Technical University in Journal of Thermal Engineering
- Vol. 6 (2) , 170-179
THE STRESS ANALYSIS ON TWO DIFFERENT ADHESIVELY BONDED T-JOINTS VIA 3D NONLINEAR FINITE ELEMENT METHOD
Adhesively bonded joints are formed in different configurations. T- adhesively bonded joint is one of these configurations and has an important position in industrial applications. The purpose of this study was to numerically study the stress distributions, strength, damage evolution of different T-joints with or without adhesive filling at the curvature of the L-shaped adherends under tensile load via 3D nonlinear finite element method. Here, type-I T-joint is the first model without adhesive filling at the curvature of the L-shaped adherends and type-II T-joint is the second model with adhesive filling at the curvature of the L-shaped adherends. In this study, FM73 and 3M 2214 adhesives and AA2024-T3 aluminum alloy adherends have been used to create two different T-joints numerically. Numerical analysis results have shown that the presence of filler adhesive has a direct influence on joint strength. It has also been observed that ABCD interface is the most critical region in terms of damage occurrence, while is AB and BC lines on the ABCD interface are the most critical lines. In addition, it was observed upon comparing the stress distributions of lines AB and BC that the shear and normal stress values decreased in lines AB and BC of the type-II T-joints. Therefore, it can be put forth that the strength of Type-II T-joints is greater in comparison with the strength of type-I T-joints and the use of a type-II T-joints is more suitable for loads which are close to the fracture load of the T-joints.