TETevfik Oğuzhan Ergüder

Tevfik Oğuzhan Ergüder

*This is an algorithmically generated author record based on publicly available information.

Tevfik Oğuzhan Ergüder has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Impact Wear Performance Of Fdm-Printed Pla: Influence Of Infill Pattern And Density

    by Mustafa Öcal, Caner Bulut, Tevfik Oğuzhan Ergüder

    This study investigates the influence of infill pattern and infill density on the impact wear behavior of FDM-printed PLA specimens. Samples were manufactured using three internal architectures (cubic, gyroid, and triangular) at two infill densities (75% and 100%) and tested under cyclic impact loading conditions. Crater diameter, crater depth, and wear volume were quantified using three-dimensional optical profilometry.The results indicate that increasing the infill density significantly improved wear resistance by reducing crater dimensions and material loss. Among the investigated architectures, the triangular pattern exhibited the lowest wear volume (0.044 mm³) and the most stable crater morphology, indicating a more efficient load-transfer capability. Statistical analysis indicated that crater diameter was significantly affected by infill pattern and, in the two-way model, by infill density, whereas crater depth and wear volume showed non-significant but consistent trends.Contact mechanics analysis indicated that the calculated Hertzian contact pressures exceeded the yielding threshold of PLA, demonstrating that the wear process occurred in an elastic–plastic regime. Cross-sectional optical observations further revealed that damage evolution transitions from subsurface collapse in cubic structures to surface-confined deformation in triangular patterns. These findings highlight the critical role of internal architecture in determining the impact wear performance of additively manufactured polymer components.

  • Effect of process parameters and annealing treatment on mechanical and surface properties of PLA samples

    by Gökhan Haydarlar, Tevfik Oğuzhan Ergüder, Semih Duran

    Context— Fused Deposition Modeling (FDM) has become a commonly adopted additive manufacturing method because it offers economical production, geometric versatility, and broad material availability. Among the thermoplastics used in FDM, polylactic acid (PLA) is widely preferred due to its environmentally friendly nature and favorable processing characteristics. Nevertheless, the mechanical properties and surface finish of PLA parts produced by FDM are highly sensitive to both manufacturing parameters and post-processing practices. Although previous research has reported the separate effects of factors such as layer thickness, infill density, and annealing, studies that systematically evaluate their combined impact are still scarce.Objective— This research focused on examining how variations in layer thickness, infill density, and annealing temperature affect the tensile performance and surface characteristics of PLA parts produced by FDM. In particular, the study aimed to determine which processing parameters most strongly influence tensile strength, elastic modulus, elongation, specific tensile strength, and surface roughness, as well as to explain their role in balancing stiffness and ductility in printed PLA parts.Method— An L9 Taguchi orthogonal array was implemented to assess the influence of layer thickness set at 0.12, 0.16, and 0.20 mm, infill density levels of 20, 40, and 60 percent, and annealing states consisting of as-printed, 60 °C, and 90 °C. Tensile samples made of PLA were fabricated using an FDM-based 3D printing system under controlled processing conditions. Mechanical characterization was carried out through tensile testing to obtain tensile strength, elastic modulus, and elongation values, whereas specific tensile strength was determined by incorporating sample mass measurements. Surface quality was evaluated by measuring the average surface roughness (Ra) with a three-dimensional optical profilometer. The effects and relative significance of the selected parameters were statistically analyzed using signal-to-noise ratios and analysis of variance techniques.Results— The results showed that infill density was the most important factor affecting tensile strength, with a contribution ratio of 87.76%, and maximum strengths of approximately 43–45 MPa obtained at 60% infill. Layer thickness was identified as the dominant parameter controlling elastic modulus (48.17%) and elongation (71.64%), its critical role in the stiffness–ductility balance. Surface roughness increased as thicker layers formed more pronounced and visible layer-step structures. Surface roughness increased as thicker layers produced more pronounced and visible layer-step structures. The overall effect of layer thickness on surface roughness was 84.73%.Conclusion— This work presents an integrated assessment of how multiple processing parameters influence the mechanical behavior and surface characteristics of PLA components. The results support the optimization of strength, ductility, weight efficiency, and surface finish, and contribute practical insight for the engineering design of PLA parts manufactured by FDM.

  • Open Access

    Mechanical characterization of FDM-printed PLA: Role of infill geometry and build direction

    by Tevfik Oğuzhan Ergüder, Caner Bulut

    This study examines the mechanical behavior of polylactic acid (PLA) components produced via Fused Deposition Modeling (FDM), focusing on the effects of infill geometry and build orientation on tensile strength and deformation. Three infill patterns‒Cubic Subdivision, Gyroid, and Tri-Hexagon‒were combined with three build orientations (0°, 45°, and 90°) using an L9 Taguchi orthogonal array to systematically evaluate their influence and identify optimal configurations. ASTM D638 Type IV tensile specimens were fabricated and tested to assess performance. The results revealed that the Gyroid pattern at a 90° build orientation achieved the highest tensile strength (987.3 N), while the 45° build orientation exhibited the greatest ductility (3.39 mm), reflecting the anisotropic mechanical behavior inherent to FDM. The Tri-Hexagon pattern displayed brittle fracture characteristics, whereas the Cubic Subdivision offered intermediate performance. Analysis of variance (ANOVA) identified infill pattern as the most significant factor, accounting for 86.52% of the variation in mechanical properties, while build orientation contributed 6.29%. These findings emphasize that infill strategy plays a far more decisive role than build orientation in determining mechanical performance. Overall, the study provides practical insights into optimizing FDM-printed components by selecting appropriate infill patterns and build orientations to meet application-specific requirements, particularly where strength or energy absorption is critical. The results can serve as a reference for designers and engineers aiming to enhance the structural efficiency and reliability of 3D-printed PLA parts.


  • Effects of process parameters on selective laser melting of Ti6Al4V-ELI alloy and parameter optimization via response surface method

    by Gürkan Kaya, Fatih Yıldız, İsmail Hakkı Korkmaz, İrFan Kaymaz, Ali Fatih Yetim, Tevfik Oğuzhan Ergüder, Çağdaş Şen


  • Effects of build orientation and hatch spacing on high-speed milling behavior of L-PBF 316L stainless steel

    by Gürkan Kaya, Uğur Köklü, Tevfik Oğuzhan Ergüder, Furkan Cengiz, Fatih Yıldız

    Due to the philosophy of the process, the surface roughness is usually high for the parts produced with laser powder bed fusion (L-PBF) additive manufacturing (AM). Parts produced by this method need surface quality improvement processes for many applications. One of the methods used for this purpose is high speed machining (HSM). HSM is a modern manufacturing technique that offers several benefits, including improved productivity, enhanced product quality, and reduced production costs. In addition, HSM can improve the quality of finished products by reducing machining errors. In this study, samples produced with 316L powder in size of 10 × 10 × 5 mm using three different hatch spacings (60, 70, 80 µm) and building orientations (0°, 45°, 90°) were produced by L-PBF method, and HSM process was applied to these samples. In this context, the present study aimed to investigate the effects of porosity, microstructure and microhardness properties of 316L samples produced by L-PBF method using different hatch spacings and build orientations on cutting forces, surface roughness and burr formation in HSM. When the numerical values of the cutting forces were analyzed in both x and y directions, it was observed that the greatest cutting force occurred in the x direction. While the Fx force ranged from 6.23 to 9.35 N, the Fy force ranged from 4.88 to 8.27 N. It has been determined that as the build orientation increases at the same hatch spacing value, the cutting forces increase due to the increased porosity ratio.


  • Tribological and thermal properties of plasma nitrided Ti45Nb alloy

    by İlyas Hacısalihoğlu, Gürkan Kaya, T. Oğuzhan Ergüder, Emre Mandev, Eyüphan Manay, Fatih Yıldız


  • Erzincan’da Motorlu Taşıtlar Tarafından Atmosfere Bırakılan Egzoz Emisyonları ve Tahmini Miktarlarının Belirlenmesi

    by Murat Çeti̇n, Tevfik Oğuzhan Ergüder

    Ülkemizde taşımacılıkta yaygın olarak kullanılmakta olan içten yanmalı motorlar ile hareket eden taşıtlardan çevreye salınan zararlı egzoz gazlarının hava kirliliği üzerinde etkin bir rolü vardır. Bu taşıtlar yaygın olarak yenilenemeyen fosil yakıtlardan üretilen benzin, motorin ve LPG gibi yakıtlarla çalıştırılmakta olup, bu yakıtların yakılması sonucunda CO, CO2, NOx ve PM gibi emisyonlar atmosfere bırakılmaktadır. Erzincan il merkezinde artmakta olan motorlu taşıt sayısıyla birlikte hava kirliliği miktarı da artmaktadır. Temel olarak motorlu taşıtların atmosfere bıraktığı emisyon miktarları hesaplanırken taşıt profili ve emisyon faktörüne gibi verilere gereksinim duyulmaktadır. Çalışmada kullanılan il merkezindeki taşıtlarla ilgili veriler, yapılan anket çalışmaları ve Erzincan Trafik Bölge Müdürlüğü’nden alınan bilgiler ile elde edilmiştir. Yapılan anketler ile farklı sınıflara ait 947 taşıta ulaşılıp, bu taşıtların üretim yılları, boyutları, Emisyon Standartları, kullandığı yakıt cinsi, kullanım amacı, segmenti gibi özellikleri belirlenmiştir. Elde edilen veriler doğrultusunda taşıtlar belirlenen sınıflara ayrıldıktan sonra COPERT 5 programı yardımıyla emisyon miktarları teorik olarak hesaplanıp, Erzincan il merkezindeki motorlu taşıt kaynaklı hava kirliliğini önlemek için öneriler sunulmuştur.