BMBole Ma

Bole Ma

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Bole Ma has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Dynamics and Control of Mass-Variable Liquid-Filled Spacecraft With Combined Nonlinear Slosh

    by Feng Liu, Baozeng Yue, Bole Ma

    This paper focuses on the dynamics and control of liquid-filled spacecraft with nonlinear slosh in multi-tank, wherein the effect of liquid propellant consumption is considered. An improved parameter-variable 3DOF-rigid-pendulum slosh model is adopted to equivalently simulate the nonlinear slosh, including large-amplitude lateral sloshing and rotary sloshing, in partially-filled spherical tanks. First, the translation-rotation dynamics of a spacecraft with combined slosh in 2-tank is derived by using the Lagrangian formulation. Second, the dynamic responses of the spacecraft coupled with combined nonlinear slosh are simulated by giving large-angle attitude maneuvering cases and zero-impulse translation maneuvering cases. Third, a wave-based attitude controller of the liquid-filled spacecraft is designed. It is found that the combined propellant slosh can disturb the rigid-body motion (translation and rotation) of spacecraft with obvious jitter in certain directions, that the propellant consumption is likely to cause the non-convergence of the translation motion of spacecraft during zero-momentum maneuvering, and that the jitter disturbance of propellant slosh on the attitude motion of spacecraft can be absorbed by using the designed wave-based attitude controller.


  • Open Access

    Nonlinear Dynamics of Cutting Process considering Higher‐Order Deformation of Composite Cutting Tool

    by Donghui Yao, Yongsheng Ren, Yuhuan Zhang, Bole Ma

    In this paper, the nonlinear dynamic analysis of the cutting process of composite cutting tool is performed. The cutting tool is simplified to a nonplanar bending rotating shaft. The higher-order bending deformation, structural damping, and gyroscopic effect of cutting tool are considered. It is assumed that cutting tool is subjected to a regenerative two-dimensional cutting force containing the first and second harmonic components. Based on the Hamilton principle, the motion equation of nonlinear chatter of the cutting system is derived. The nonlinear ordinary differential equations in the generalized coordinates are obtained by Galerkin method. In order to analyze the nonlinear dynamic response of cutting process, the multiscale method is used to derive the analytical approximate solution of the forced response for the cutting system under periodic cutting forces. In the forced response analysis, four cases including primary resonance and superharmonic resonance, i.e., , , , and , are considered. The influences of ratio of length to diameter, structural damping, cutting force, and ply angle on primary resonance and superharmonic resonance are investigated. The results show that nonlinearity due to higher-order bending deformation significantly affects the dynamic behavior of the milling process and that the effective nonlinearity of the cutting system is of hard type. Multivalued resonance curves and jump phenomenon are presented. The influences of various factors, such as ratio of length to diameter, ply angle, structural damping, cutting force, and rotating speed, are thoroughly discussed.


  • Open Access

    Nonlinear Dynamic Analysis of the Cutting Process of a Nonextensible Composite Boring Bar

    by Bole Ma, Yongsheng Ren

    A nonlinear dynamic analysis of the cutting process of a nonextensible composite cutting bar is presented. The cutting bar is simplified as a cantilever with plane bending. The nonlinearity is mainly originated from the nonextensible assumption, and the material of cutting bar is assumed to be viscoelastic composite, which is described by the Kelvin–Voigt equation. The motion equation of nonlinear chatter of the cutting system is derived based on the Hamilton principle. The partial differential equation of motion is discretized using the Galerkin method to obtain a 1-dof nonlinear ordinary differential equation in a generalized coordinate system. The steady forced response of the cutting system under periodically varying cutting force is approximately solved by the multiscale method. Meanwhile, the effects of parameters such as the geometry of the cutting bar (including length and diameter), damping, the cutting coefficient, the cutting depth, the number of the cutting teeth, the amplitude of the cutting force, and the ply angle on nonlinear lobes and primary resonance curves during the cutting process are investigated using numerical calculations. The results demonstrate that the critical cutting depth is inversely proportional to the aspect ratio of the cutting bar and the cutting force coefficient. Meanwhile, the chatter stability in the milling process can be significantly enhanced by increasing the structural damping. The peak of the primary resonance curve is bent toward the right side. Due to the cubic nonlinearity in the cutting system, primary resonance curves show the characteristics of typical Duffing’s vibrator with hard spring, and jump and multivalue regions appear.