Venkateswara Babu Peddakondigalla
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Venkateswara Babu Peddakondigalla has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
Ismail Syed
National Institute of Technology Warangal
3 shared publications- Vasavi Boggarapu
VIT-AP University
3 shared publications - Gujjala Raghavendra
Department of Mechanical Engineering, National Institute of Technology, Warangal, India
2 shared publications Jayachandra Gujjala
National Institute of Technology
2 shared publicationsRajani Doppalapudi
Department of English, RVR & JC College of Engineering, Guntur, India
2 shared publicationsShakuntla Ojha
Kakatiya Institute of Technology & Science
2 shared publications
Latest Publications
- Open Access
- 11 May 2024
- Published by Springer Nature in Journal of Engineering and Applied Science
- Vol. 71 (1) , 1-10
Investigation on mechanical and thermal behaviour of graphene bonded carbon/Kevlar hybrid fabric polymer composites
The present research is aimed to understand the influence of graphene-reinforced carbon/Kevlar hybrid fabric epoxy composites. Samples HG0, HG2, HG4, and HG6 are fabricated using four layers of fabric mat and with varying graphene weight percentage as 0, 2, 4, and 6 wt.%, respectively. Mechanical characterizations such as hardness, tensile, and flexural strength were individually assessed. Thermal stability is evaluated through thermos-gravimetric analysis. Composite HG6 with high filler loading showed 71% and 114.4% greater tensile and flexural strength compared to unfilled HG0 specimen. Similarly, HG6 exhibited greater thermal stability. Inclusion of graphene particles in higher concentration improved the interfacial bonding between fibre/matrix/filler system. Fracture surfaces are analysed using scanning electron microscopy to understand the failure mechanisms.
- 11 May 2024
- Published by Springer Nature in Journal of Engineering and Applied Science
- Vol. 71 (1) , 1-10
Open AccessInvestigation on mechanical and thermal behaviour of graphene bonded carbon/Kevlar hybrid fabric polymer composites
The present research is aimed to understand the influence of graphene-reinforced carbon/Kevlar hybrid fabric epoxy composites. Samples HG0, HG2, HG4, and HG6 are fabricated using four layers of fabric mat and with varying graphene weight percentage as 0, 2, 4, and 6 wt.%, respectively. Mechanical characterizations such as hardness, tensile, and flexural strength were individually assessed. Thermal stability is evaluated through thermos-gravimetric analysis. Composite HG6 with high filler loading showed 71% and 114.4% greater tensile and flexural strength compared to unfilled HG0 specimen. Similarly, HG6 exhibited greater thermal stability. Inclusion of graphene particles in higher concentration improved the interfacial bonding between fibre/matrix/filler system. Fracture surfaces are analysed using scanning electron microscopy to understand the failure mechanisms.
- 20 March 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (6) , 2750-2758
A novel approach to develop and characterize bi-directional aluminum-copper functionally graded material
A substantial increase in research activity on functionally graded materials (FGMs) was foreseen in the past few decades owing to their high strength and stiffness, design flexibility, and multi-functional features. However, the majority of the literature was confined to uni-directional (1D) gradation in material constituents. As a result, their usage was limited to a few advanced applications such as aircraft frames and shuttles, propulsion systems, and machine elements wherein the temperature is distributed along two or more directions. Thus, there is a demand for FGM that shows property variations in bi (2D) or tri (3D) directions. The present research work is an attempt made to design and develop bi-directional functionally graded material (2D FGM) with aluminum (Al) and copper particles. A 2D FGM sample in the form of a rectangular slab having material variation along x and y directions was produced through powder metallurgy using a 3D-printed cuboid. Variations in microstructure and hardness confirm the material gradation in two directions. Change in erosion wear at different locations was also observed on the sample. Furthermore, worn-out surfaces using scanning electron micrographs revealed a ductile fracture.
- 20 March 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (6) , 2750-2758
A novel approach to develop and characterize bi-directional aluminum-copper functionally graded material
A substantial increase in research activity on functionally graded materials (FGMs) was foreseen in the past few decades owing to their high strength and stiffness, design flexibility, and multi-functional features. However, the majority of the literature was confined to uni-directional (1D) gradation in material constituents. As a result, their usage was limited to a few advanced applications such as aircraft frames and shuttles, propulsion systems, and machine elements wherein the temperature is distributed along two or more directions. Thus, there is a demand for FGM that shows property variations in bi (2D) or tri (3D) directions. The present research work is an attempt made to design and develop bi-directional functionally graded material (2D FGM) with aluminum (Al) and copper particles. A 2D FGM sample in the form of a rectangular slab having material variation along x and y directions was produced through powder metallurgy using a 3D-printed cuboid. Variations in microstructure and hardness confirm the material gradation in two directions. Change in erosion wear at different locations was also observed on the sample. Furthermore, worn-out surfaces using scanning electron micrographs revealed a ductile fracture.
- 3 January 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 237 (7) , 1592-1602
Experimental study on tribological behavior of aluminum–copper functionally graded material
A five-layered aluminum–copper metal functionally graded material was developed through powder metallurgy process. The sample comprises different weight percentages of copper and aluminum that vary from 0 wt% to 100 wt % along the thickness direction. Erosion wear was performed on air jet erosion testing apparatus at a constant impact angle of 90 o and impact velocity of 151 m/s. It was observed that erosion wear decreases when there is an increase in copper content. Layer 1 comprising 100 wt% of copper has shown 76.92% lower wear compared to layer 5 (100 wt% of aluminum). Besides, erosion resistance was enhanced at graded layers due to the formation of Al 2 Cu phase during sintering. Abrasive wear of metal functionally graded material was evaluated on the pin-on-disc test apparatus. Experiments were conducted at different loading conditions on various abrasive surfaces (P120, P800, and P2000). Irrespective of abrasive surface, the specific wear rate of aluminum–copper metal functionally graded material sample increased with an increase in load from 5N to 15N. At 5N, abrasive wear of metal functionally graded material on P2000 grit surface was 87.7% and 27.19% lower compared to P120 and P800, respectively. Eroded and worn-out surfaces were examined microscopically to understand the wear mechanisms and are discussed in detail.
- 3 January 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 237 (7) , 1592-1602
Experimental study on tribological behavior of aluminum–copper functionally graded material
A five-layered aluminum–copper metal functionally graded material was developed through powder metallurgy process. The sample comprises different weight percentages of copper and aluminum that vary from 0 wt% to 100 wt % along the thickness direction. Erosion wear was performed on air jet erosion testing apparatus at a constant impact angle of 90 o and impact velocity of 151 m/s. It was observed that erosion wear decreases when there is an increase in copper content. Layer 1 comprising 100 wt% of copper has shown 76.92% lower wear compared to layer 5 (100 wt% of aluminum). Besides, erosion resistance was enhanced at graded layers due to the formation of Al 2 Cu phase during sintering. Abrasive wear of metal functionally graded material was evaluated on the pin-on-disc test apparatus. Experiments were conducted at different loading conditions on various abrasive surfaces (P120, P800, and P2000). Irrespective of abrasive surface, the specific wear rate of aluminum–copper metal functionally graded material sample increased with an increase in load from 5N to 15N. At 5N, abrasive wear of metal functionally graded material on P2000 grit surface was 87.7% and 27.19% lower compared to P120 and P800, respectively. Eroded and worn-out surfaces were examined microscopically to understand the wear mechanisms and are discussed in detail.
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2810 (1) , 120003
Effect of graded layers on void formation in metal based functionally graded materials
Metal based functionally graded materials (FGMs) were fabricated using aluminum and copper particles. Three different samples having 3 layers (3L), 6 layers (6L) and 10 layers (10L) with change in volume fractions of constituents at the layers were developed. Gradation is achieved along the thickness direction. The results showed the decrease in void fraction with an increase in number of layers up to the critical limit. Beyond that increment in void content was observed. Compared to 10L, the samples 6L have displayed 48% lesser void fraction. While, 3L have shown 69.4% and 41.88% greater voids as compared to 6L and 10L respectively.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2810 (1) , 120003
Open AccessEffect of graded layers on void formation in metal based functionally graded materials
Metal based functionally graded materials (FGMs) were fabricated using aluminum and copper particles. Three different samples having 3 layers (3L), 6 layers (6L) and 10 layers (10L) with change in volume fractions of constituents at the layers were developed. Gradation is achieved along the thickness direction. The results showed the decrease in void fraction with an increase in number of layers up to the critical limit. Beyond that increment in void content was observed. Compared to 10L, the samples 6L have displayed 48% lesser void fraction. While, 3L have shown 69.4% and 41.88% greater voids as compared to 6L and 10L respectively.
- Open Access
- 1 April 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1112 (1) , 012008
Hydrodynamic Performance of Positive Surface Textured Patterns under Mixed Lubrication
It is proved that the optimal design of surface textures (positive or negative) improve the lubrication performance by generating extra hydrodynamic pressure at the interface of the sliding pairs. In the present work, the effect of various positive surface textures on hydrodynamic performance of parallel sliding contact under mixed lubrication is researched. The modified Reynolds equation and asperity contact model are solved simultaneously to assess the hydrodynamic pressure and minimum film thickness for different shape of textures. The results depict that elliptical shaped texture generate high hydrodynamic pressure as well as minimum film thickness at the conjunction than the other texture shapes.
- 1 April 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1112 (1) , 012008
Open AccessHydrodynamic Performance of Positive Surface Textured Patterns under Mixed Lubrication
It is proved that the optimal design of surface textures (positive or negative) improve the lubrication performance by generating extra hydrodynamic pressure at the interface of the sliding pairs. In the present work, the effect of various positive surface textures on hydrodynamic performance of parallel sliding contact under mixed lubrication is researched. The modified Reynolds equation and asperity contact model are solved simultaneously to assess the hydrodynamic pressure and minimum film thickness for different shape of textures. The results depict that elliptical shaped texture generate high hydrodynamic pressure as well as minimum film thickness at the conjunction than the other texture shapes.
- 5 June 2020
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 235 (2) , 360-375
Experimental and numerical studies of positive texture effect on friction reduction of sliding contact under mixed lubrication
Textured surfaces have been remarkable in improving the frictional performance of sliding contacts, particularly at instances such as boundary or mixed lubrication regimes. This article reports the results of an experimental and numerical study carried out by introducing surface textures in the form of protrusions to investigate its effects on friction performance under a mixed lubrication regime. The surface textures produced by the chemical etching process are tested on the pin on disc test rig by varying area density and height of the texture. In numerical simulation, the modified Reynolds equation (Patir–Cheng flow model) and asperity contact model (Greenwood–Tripp model) are solved for hydrodynamic and asperity pressures, respectively. The results indicate that the experimental measurements are qualitatively in good agreement with numerical predictions. Furthermore, the simulations are performed for different texture shapes by varying texture area density, height, and sliding velocity. The results depict that a maximum friction reduction of 87% with elliptical textures compared to the un-textured case.
- 5 June 2020
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 235 (2) , 360-375
Experimental and numerical studies of positive texture effect on friction reduction of sliding contact under mixed lubrication
Textured surfaces have been remarkable in improving the frictional performance of sliding contacts, particularly at instances such as boundary or mixed lubrication regimes. This article reports the results of an experimental and numerical study carried out by introducing surface textures in the form of protrusions to investigate its effects on friction performance under a mixed lubrication regime. The surface textures produced by the chemical etching process are tested on the pin on disc test rig by varying area density and height of the texture. In numerical simulation, the modified Reynolds equation (Patir–Cheng flow model) and asperity contact model (Greenwood–Tripp model) are solved for hydrodynamic and asperity pressures, respectively. The results indicate that the experimental measurements are qualitatively in good agreement with numerical predictions. Furthermore, the simulations are performed for different texture shapes by varying texture area density, height, and sliding velocity. The results depict that a maximum friction reduction of 87% with elliptical textures compared to the un-textured case.
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 24, 1112-1121
Experimental investigation on effects of positive texturing on friction and wear reduction of piston ring/cylinder liner system
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 24, 1112-1121
Experimental investigation on effects of positive texturing on friction and wear reduction of piston ring/cylinder liner system
- 7 May 2019
- Published by Emerald Publishing in Industrial Lubrication and Tribology
- Vol. 71 (4) , 515-524
Influence of positive texturing on friction and wear properties of piston ring-cylinder liner tribo pair under lubricated conditions
Purpose: In an internal combustion engine, piston ring-cylinder liner tribo pair is one among the most critical rubbing pairs. Most of the energy produced by an internal combustion engine is dissipated as frictional losses of which major portion is contributed by the piston ring-cylinder liner tribo pair. Hence, proper design of tribological parameters of piston ring-cylinder liner pair is essential and can effectively reduce the friction and wear, thereby improving the tribological performance of the engine. This paper aims to use surface texturing, an effective and feasible method, to improve the tribological performance of piston ring-cylinder liner tribo pair. Design/methodology/approach: In this paper, influence of positive texturing (protruding) on friction reduction and wear resistance of piston ring surfaces was studied. The square-shaped positive textures were fabricated on piston ring surface by chemical etching method, and the experiments were conducted with textured piston ring surfaces against un-textured cylinder liner surface on pin-on-disc apparatus by continuous supply of lubricant at the inlet of contact zone. The parameters varied in this study are area density and normal load at a constant sliding speed. A comparison was made between the tribological properties of textured and un-textured piston ring surfaces. Findings: From the experimental results, the tribological performance of the textured piston ring-cylinder liner tribo pair was significantly improved over a un-textured tribo pair. A maximum friction reduction of 67.6 per cent and wear resistance of 81.6 per cent were observed with textured ring surfaces as compared to un-textured ring surfaces. Originality/value: This experimental study is helpful for better understanding of the potency of positive texturing on friction reduction and wear resistance of piston ring-cylinder liner tribo pair under lubricated sliding conditions.
- 7 May 2019
- Published by Emerald Publishing in Industrial Lubrication and Tribology
- Vol. 71 (4) , 515-524
Influence of positive texturing on friction and wear properties of piston ring-cylinder liner tribo pair under lubricated conditions
Purpose: In an internal combustion engine, piston ring-cylinder liner tribo pair is one among the most critical rubbing pairs. Most of the energy produced by an internal combustion engine is dissipated as frictional losses of which major portion is contributed by the piston ring-cylinder liner tribo pair. Hence, proper design of tribological parameters of piston ring-cylinder liner pair is essential and can effectively reduce the friction and wear, thereby improving the tribological performance of the engine. This paper aims to use surface texturing, an effective and feasible method, to improve the tribological performance of piston ring-cylinder liner tribo pair. Design/methodology/approach: In this paper, influence of positive texturing (protruding) on friction reduction and wear resistance of piston ring surfaces was studied. The square-shaped positive textures were fabricated on piston ring surface by chemical etching method, and the experiments were conducted with textured piston ring surfaces against un-textured cylinder liner surface on pin-on-disc apparatus by continuous supply of lubricant at the inlet of contact zone. The parameters varied in this study are area density and normal load at a constant sliding speed. A comparison was made between the tribological properties of textured and un-textured piston ring surfaces. Findings: From the experimental results, the tribological performance of the textured piston ring-cylinder liner tribo pair was significantly improved over a un-textured tribo pair. A maximum friction reduction of 67.6 per cent and wear resistance of 81.6 per cent were observed with textured ring surfaces as compared to un-textured ring surfaces. Originality/value: This experimental study is helpful for better understanding of the potency of positive texturing on friction reduction and wear resistance of piston ring-cylinder liner tribo pair under lubricated sliding conditions.