MÖMustafa Öcal

Mustafa Öcal

*This is an algorithmically generated author record based on publicly available information.

Mustafa Öcal has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Impact Wear Performance Of Fdm-Printed Pla: Influence Of Infill Pattern And Density

    by Mustafa Öcal, Caner Bulut, Tevfik Oğuzhan Ergüder

    This study investigates the influence of infill pattern and infill density on the impact wear behavior of FDM-printed PLA specimens. Samples were manufactured using three internal architectures (cubic, gyroid, and triangular) at two infill densities (75% and 100%) and tested under cyclic impact loading conditions. Crater diameter, crater depth, and wear volume were quantified using three-dimensional optical profilometry.The results indicate that increasing the infill density significantly improved wear resistance by reducing crater dimensions and material loss. Among the investigated architectures, the triangular pattern exhibited the lowest wear volume (0.044 mm³) and the most stable crater morphology, indicating a more efficient load-transfer capability. Statistical analysis indicated that crater diameter was significantly affected by infill pattern and, in the two-way model, by infill density, whereas crater depth and wear volume showed non-significant but consistent trends.Contact mechanics analysis indicated that the calculated Hertzian contact pressures exceeded the yielding threshold of PLA, demonstrating that the wear process occurred in an elastic–plastic regime. Cross-sectional optical observations further revealed that damage evolution transitions from subsurface collapse in cubic structures to surface-confined deformation in triangular patterns. These findings highlight the critical role of internal architecture in determining the impact wear performance of additively manufactured polymer components.

  • Effects of boron and chromium carbide on impact wear and corrosion behavior of copper composites produced by powder metallurgy

    by Mustafa Öcal, Caner Bulut, Üsame Ali Usca, Serhat Şap, Mahir Uzun

    In this study, the effects of boron (B) and chromium carbide (Cr 3 C 2 ) reinforcements on the impact wear and corrosion behaviour of copper-based composites produced by powder metallurgy were investigated. Composites containing 0, 5 and 10 wt.% reinforcement were characterised using X-ray diffraction, scanning electron microscope–energy-dispersive X-ray spectroscopy, optical microscopy and three-dimensional profilometry. Impact wear tests were performed under cyclic loading conditions of 10,000 and 100,000 cycles at 2.0 and 3.0 Hz, while corrosion performance was evaluated in 3.5 wt.% NaCl solution using potentiodynamic polarisation. The CuBCr5 composite exhibited the lowest volume loss under the investigated impact wear conditions, with a minimum value of 0.030 mm 3 and a value of 0.200 mm 3 under the most severe condition. In addition, CuBCr5 showed the best corrosion resistance, with a corrosion rate of 0.808 mpy and a corrosion current density of 2.00 µA/cm 2 . These improvements were attributed to improved densification, grain refinement, more homogeneous reinforcement distribution and the possible development of a more stable protective surface layer. Although reinforcement addition reduced the electrical conductivity compared with Pure Cu, the CuBCr5 composite maintained a more stable conductivity response than CuBCr10 within the investigated frequency range. Overall, the results indicate that 5 wt.% B–Cr 3 C 2 reinforcement provides the most balanced combination of impact wear resistance, corrosion resistance and electrical response in Cu-based composites.

  • Makine Mühendisliğinde Yükselen Eğilimler: Teori, Uygulama ve Yenilikçi Yaklaşımlar Emerging Trends in Mechanical Engineering: Theory, Applications, and Innovative Approaches

    by Tezcan Şekercioğlu, Nesrin Uzun Kaya, Mustafa Armağan, Yasemin Yıldıran Avcu, Arda Turacı, Murat Makaracı, Caner Bulut, Mustafa Öcal, Muhammet Mustafa Bahşı

    Bu kitap, makine mühendisliğinin günümüzde hızla gelişen beş farklı alanını bir araya getirerek kapsamlı ve disiplinler arası bir bakış açısı sunmaktadır. Kitap; mühendislik sistemlerinde gözlenebilirlik ve fiziksel temsil sınırlarına dair kavramsal bir tartışmayla açılmakta, ardından yüksek entropili alaşımların malzeme tasarımındaki rolünü, dişli mühendisliğinde kalite ve modifikasyon konularını, son olarak da magnezyum alaşımlarının yüzey mühendisliği yoluyla performans geliştirme stratejilerini ele almaktadır. Korozyondan aşınmaya, alaşım tasarımından hassas imalat toleranslarına kadar geniş bir yelpazede sunulan bu özgün çalışmalar; akademisyenler, mühendislik öğrencileri ve sektör profesyonelleri için güncel literatürle desteklenmiş değerli bir başvuru kaynağı niteliği taşımaktadır.