Tahmid Kaisar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Tahmid Kaisar has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Philip X. -L. Feng
University of Florida
8 shared publications - Cristian Cassella
Northeastern University
3 shared publications - Nicolas Casilli
Northeastern University
3 shared publications - Jaesung Lee
Department of Electrical & Computer Engineering, College of Engineering & Computer Science University of Central Florida, Orlando, USA
2 shared publications - Jayasimha Atulasimha
Virginia Commonwealth University
2 shared publications - Mina Rais-Zadeh
NASA Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA, USA
2 shared publications
Latest Publications
- 10 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 35 (3) , 381-398
Synchronization Dynamics of MEMS Oscillators With Sub-Harmonic Injection Locking (SHIL) for Emulating Artificial Ising Spins
This paper reports on synchronization dynamics in coupled self-sustaining oscillators referenced to bulk acoustic wave (BAW) resonant microelectromechanical systems (MEMS), for emulating artificial Ising spins. Bistable phase states are created by applying a sub-harmonic injection locking (SHIL) signal to a piezoelectric aluminum nitride-on-silicon (AlN-on-Si or AlN/Si) length-extensional (LE) mode MEMS feedback oscillator, which is the first realization of emulating spin up and down states of the Ising model using BAW MEMS self-sustaining oscillators. The oscillator performance specifications, including phase noise and frequency stability (Allan deviation), are characterized prior to initiation of coupling and synchronization. The probabilities of obtaining bistable phase states are then determined as a function of SHIL amplitude. Detailed theoretical and experimental analyses of the stable operation of AlN/Si MEMS oscillators in the nonlinear regime and the dynamics of a single BAW MEMS oscillator synchronized to SHIL are presented. The initial experimental realization of two coupled MEMS oscillators allows for careful calibration of the parameters governing synchronization dynamics, including amplitude-frequency dependency via the resonance backbone curve, frequency detuning, and coupling between oscillators. The measured results show that the synchronization bandwidth can be varied by increasing the SHIL amplitude at a fixed coupling strength, which provides flexibility in synchronizing multiple oscillators for building MEMS oscillator Ising machines. Finally, the probability of obtaining an out-of-phase state (for reactive coupling) and an in-phase state (for dissipative coupling) is studied as a function of the coupling coefficient, thus enabling its optimal value to be found. [2024-0161]
- 10 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 35 (3) , 381-398
Synchronization Dynamics of MEMS Oscillators With Sub-Harmonic Injection Locking (SHIL) for Emulating Artificial Ising Spins
This paper reports on synchronization dynamics in coupled self-sustaining oscillators referenced to bulk acoustic wave (BAW) resonant microelectromechanical systems (MEMS), for emulating artificial Ising spins. Bistable phase states are created by applying a sub-harmonic injection locking (SHIL) signal to a piezoelectric aluminum nitride-on-silicon (AlN-on-Si or AlN/Si) length-extensional (LE) mode MEMS feedback oscillator, which is the first realization of emulating spin up and down states of the Ising model using BAW MEMS self-sustaining oscillators. The oscillator performance specifications, including phase noise and frequency stability (Allan deviation), are characterized prior to initiation of coupling and synchronization. The probabilities of obtaining bistable phase states are then determined as a function of SHIL amplitude. Detailed theoretical and experimental analyses of the stable operation of AlN/Si MEMS oscillators in the nonlinear regime and the dynamics of a single BAW MEMS oscillator synchronized to SHIL are presented. The initial experimental realization of two coupled MEMS oscillators allows for careful calibration of the parameters governing synchronization dynamics, including amplitude-frequency dependency via the resonance backbone curve, frequency detuning, and coupling between oscillators. The measured results show that the synchronization bandwidth can be varied by increasing the SHIL amplitude at a fixed coupling strength, which provides flexibility in synchronizing multiple oscillators for building MEMS oscillator Ising machines. Finally, the probability of obtaining an out-of-phase state (for reactive coupling) and an in-phase state (for dissipative coupling) is studied as a function of the coupling coefficient, thus enabling its optimal value to be found. [2024-0161]
- 3 June 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (23)
Noise matching and sensitivity improvement in aluminum nitride nanoelectromechanical resonators via parametric amplification
Parametric amplification of ultrasmall signals from electromechanical transducers directly in the mechanical domain, prior to electrical readout, is an intriguing challenge and is important for both scientific measurements and technologies utilizing micro/nanoelectromechanical systems (MEMS/NEMS). Here, we report on parametric amplification of aluminum nitride (AlN) multimode NEMS resonators (with broad intrinsic dynamic ranges up to 90 dB) for enabling detection of their thermomechanical resonances in both optical and electrical readout schemes simultaneously. The experiments demonstrate that, upon parametric pumping, the electrically transduced thermomechanical motions experience significant amplification, surpassing the extrinsic electronic noise level, while still below the parametric pumping threshold. We achieve noise matching that enables room temperature force sensitivity of 0.46 fN/Hz1/2. We observe high parametric gain up to 650, accompanied by a strong boost (over 3.5×) in the effective quality factor (Qeff, from 9000 to 32 000). These findings underscore the utilities of parametric amplification in noise matching and improving force sensitivity for NEMS transducers and their emerging applications.
- 3 June 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (23)
Noise matching and sensitivity improvement in aluminum nitride nanoelectromechanical resonators via parametric amplification
Parametric amplification of ultrasmall signals from electromechanical transducers directly in the mechanical domain, prior to electrical readout, is an intriguing challenge and is important for both scientific measurements and technologies utilizing micro/nanoelectromechanical systems (MEMS/NEMS). Here, we report on parametric amplification of aluminum nitride (AlN) multimode NEMS resonators (with broad intrinsic dynamic ranges up to 90 dB) for enabling detection of their thermomechanical resonances in both optical and electrical readout schemes simultaneously. The experiments demonstrate that, upon parametric pumping, the electrically transduced thermomechanical motions experience significant amplification, surpassing the extrinsic electronic noise level, while still below the parametric pumping threshold. We achieve noise matching that enables room temperature force sensitivity of 0.46 fN/Hz1/2. We observe high parametric gain up to 650, accompanied by a strong boost (over 3.5×) in the effective quality factor (Qeff, from 9000 to 32 000). These findings underscore the utilities of parametric amplification in noise matching and improving force sensitivity for NEMS transducers and their emerging applications.
- 2 April 2024
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 132 (14) , 147301
Parametric Frequency Divider Based Ising Machines
We report on a new class of Ising machines (IMs) that rely on coupled parametric frequency dividers (PFDs) as macroscopic artificial spins. Unlike the IM counterparts based on subharmonic-injection locking (SHIL), PFD IMs do not require strong injected continuous-wave signals or applied dc voltages. Therefore, they show a significantly lower power consumption per spin compared to SHIL-based IMs, making it feasible to accurately solve large-scale combinatorial optimization problems that are hard or even impossible to solve by using the current von Neumann computing architectures. Furthermore, using high quality factor resonators in the PFD design makes PFD IMs able to exhibit a nanowatt-level power per spin. Also, it remarkably allows a speedup of the phase synchronization among the PFDs, resulting in shorter time to solution and lower energy to solution despite the resonators’ longer relaxation time. As a proof of concept, a 4-node PFD IM has been demonstrated. This IM correctly solves a set of Max-Cut problems while consuming just 600 nanowatts per spin. This power consumption is 2 orders of magnitude lower than the power per spin of state-of-the-art SHIL-based IMs operating at the same frequency.
- 2 April 2024
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 132 (14) , 147301
Parametric Frequency Divider Based Ising Machines
We report on a new class of Ising machines (IMs) that rely on coupled parametric frequency dividers (PFDs) as macroscopic artificial spins. Unlike the IM counterparts based on subharmonic-injection locking (SHIL), PFD IMs do not require strong injected continuous-wave signals or applied dc voltages. Therefore, they show a significantly lower power consumption per spin compared to SHIL-based IMs, making it feasible to accurately solve large-scale combinatorial optimization problems that are hard or even impossible to solve by using the current von Neumann computing architectures. Furthermore, using high quality factor resonators in the PFD design makes PFD IMs able to exhibit a nanowatt-level power per spin. Also, it remarkably allows a speedup of the phase synchronization among the PFDs, resulting in shorter time to solution and lower energy to solution despite the resonators’ longer relaxation time. As a proof of concept, a 4-node PFD IM has been demonstrated. This IM correctly solves a set of Max-Cut problems while consuming just 600 nanowatts per spin. This power consumption is 2 orders of magnitude lower than the power per spin of state-of-the-art SHIL-based IMs operating at the same frequency.
- 5 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 70 (10) , 1213-1228
Five Low-Noise Stable Oscillators Referenced to the Same Multimode AlN/Si MEMS Resonator
We report on the first experimental demonstration of five self-sustaining feedback oscillators referenced to a single multimode resonator, using piezoelectric aluminum nitride on silicon (AlN/Si) microelectromechanical systems (MEMS) technology. Integrated piezoelectric transduction enables efficient readout of five resonance modes of the same AlN/Si MEMS resonator, at 10MHz, 30MHz, 65MHz, 95MHz, and 233MHz with quality ( Q ) factors of 18600, 4350, 4230, 2630, and 2138, respectively. Five stable self-sustaining oscillators are built, each referenced to one of these high- Q modes, and their mode-dependent phase noise and frequency stability (Allan deviation) are measured and analyzed. The 10, 30, 65, 95 and 233MHz oscillators exhibit low phase noise of -116, -100, -105, -106 and -92dBc/Hz at 1kHz offset frequency, respectively. The 65MHz oscillator yields Allan deviation of 4×10 -9 and 2×10 -7 at 1s and 1000s averaging time, respectively. The 10MHz oscillator’s low phase noise holds strong promise for clock and timing applications. The five oscillators’ overall promising performance also suggests suitability for multimode resonant sensing and tracking. This work also elucidates mode dependency in oscillator noise and stability, one of the key attributes of mode-engineerable resonators.
- 5 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 70 (10) , 1213-1228
Five Low-Noise Stable Oscillators Referenced to the Same Multimode AlN/Si MEMS Resonator
We report on the first experimental demonstration of five self-sustaining feedback oscillators referenced to a single multimode resonator, using piezoelectric aluminum nitride on silicon (AlN/Si) microelectromechanical systems (MEMS) technology. Integrated piezoelectric transduction enables efficient readout of five resonance modes of the same AlN/Si MEMS resonator, at 10MHz, 30MHz, 65MHz, 95MHz, and 233MHz with quality ( Q ) factors of 18600, 4350, 4230, 2630, and 2138, respectively. Five stable self-sustaining oscillators are built, each referenced to one of these high- Q modes, and their mode-dependent phase noise and frequency stability (Allan deviation) are measured and analyzed. The 10, 30, 65, 95 and 233MHz oscillators exhibit low phase noise of -116, -100, -105, -106 and -92dBc/Hz at 1kHz offset frequency, respectively. The 65MHz oscillator yields Allan deviation of 4×10 -9 and 2×10 -7 at 1s and 1000s averaging time, respectively. The 10MHz oscillator’s low phase noise holds strong promise for clock and timing applications. The five oscillators’ overall promising performance also suggests suitability for multimode resonant sensing and tracking. This work also elucidates mode dependency in oscillator noise and stability, one of the key attributes of mode-engineerable resonators.
- 14 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (6) , 7273-7283
Micromachined Thin Film Ceramic PZT Multimode Resonant Temperature Sensor
Micromachined thin-film lead zirconate titanate (PZT) retains exceptional piezoelectric and energy-harvesting capabilities, thus offering an excellent platform for enabling efficient piezoelectric microsystems on chip. Here, we design and fabricate thin-film ceramic PZT piezoelectric microelectromechanical systems (MEMS) operating on flexural-mode resonances, by using wafer bonding and chemical mechanical polishing (CMP) techniques. We describe the experimental demonstration of an integrated multimode resonant PZT MEMS temperature sensor. The three resonance modes examined (at 1.1, 3.6, 6.8MHz) all exhibit excellent linearity and responsivity to temperature variations in the range of 25°C to 211°C, with temperature coefficients of resonance frequency (TC f ) at -200ppm/°C to -270ppm/°C for open-loop measurement. We have demonstrated dual-mode temperature sensing with real-time tracking of the resonance frequency using a phase-locked loop (PLL). We have also built a self-sustaining MEMS oscillator and studied the closed-loop TC f . We compare the open-loop and closed-loop TC f s in both air and vacuum and find that the TC f can be affected by heating method, pressure, and measurement scheme. The results extend the understanding of temperature effects on the resonance frequency of PZT MEMS, demonstrate real-time temperature sensing, and pave the way for enabling multifunctional PZT microsystems on chip.
- 14 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (6) , 7273-7283
Micromachined Thin Film Ceramic PZT Multimode Resonant Temperature Sensor
Micromachined thin-film lead zirconate titanate (PZT) retains exceptional piezoelectric and energy-harvesting capabilities, thus offering an excellent platform for enabling efficient piezoelectric microsystems on chip. Here, we design and fabricate thin-film ceramic PZT piezoelectric microelectromechanical systems (MEMS) operating on flexural-mode resonances, by using wafer bonding and chemical mechanical polishing (CMP) techniques. We describe the experimental demonstration of an integrated multimode resonant PZT MEMS temperature sensor. The three resonance modes examined (at 1.1, 3.6, 6.8MHz) all exhibit excellent linearity and responsivity to temperature variations in the range of 25°C to 211°C, with temperature coefficients of resonance frequency (TC f ) at -200ppm/°C to -270ppm/°C for open-loop measurement. We have demonstrated dual-mode temperature sensing with real-time tracking of the resonance frequency using a phase-locked loop (PLL). We have also built a self-sustaining MEMS oscillator and studied the closed-loop TC f . We compare the open-loop and closed-loop TC f s in both air and vacuum and find that the TC f can be affected by heating method, pressure, and measurement scheme. The results extend the understanding of temperature effects on the resonance frequency of PZT MEMS, demonstrate real-time temperature sensing, and pave the way for enabling multifunctional PZT microsystems on chip.
- 15 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
An Ising Tag with a LiNbO3 Resonator For Temperature Threshold Sensing
SummaryWe present the first Ising-Tag (ITag) ever reported. This passive system implements a remote temperature threshold sensing functionality while using only a set of passive components including a LiNbO 3 microacoustic resonator fabricated in-house. Our ITag is formed by two battery-less RF parametric oscillators (POs) that operate as Ising spins. The POs are coupled by the LiNbO 3 device, and their output signals are combined with a power combiner to form the ITag’s response signal (v out ). The reported ITag operates with an interrogation frequency of 904 MHz and an output frequency (f out ) of 452 MHz. Depending on whether the ITag’s temperature (Ta) is lower or higher than a certain value (T th = 40 °C), the two POs can exhibit an anti-ferromagnetic or ferromagnetic interaction. The spin interaction is set by the position of the resonance frequency of the coupling LiNbO 3 device with respect to f out . Such a unique dynamical feature renders v out negligible only for T a < T th , while turning v out into an "alarm signal" for T a ≥ T th . Excitingly this is achieved without requiring an operation near a point of marginal stability or the use of any batteries or integrated circuits.
- 15 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
An Ising Tag with a LiNbO3 Resonator For Temperature Threshold Sensing
SummaryWe present the first Ising-Tag (ITag) ever reported. This passive system implements a remote temperature threshold sensing functionality while using only a set of passive components including a LiNbO 3 microacoustic resonator fabricated in-house. Our ITag is formed by two battery-less RF parametric oscillators (POs) that operate as Ising spins. The POs are coupled by the LiNbO 3 device, and their output signals are combined with a power combiner to form the ITag’s response signal (v out ). The reported ITag operates with an interrogation frequency of 904 MHz and an output frequency (f out ) of 452 MHz. Depending on whether the ITag’s temperature (Ta) is lower or higher than a certain value (T th = 40 °C), the two POs can exhibit an anti-ferromagnetic or ferromagnetic interaction. The spin interaction is set by the position of the resonance frequency of the coupling LiNbO 3 device with respect to f out . Such a unique dynamical feature renders v out negligible only for T a < T th , while turning v out into an "alarm signal" for T a ≥ T th . Excitingly this is achieved without requiring an operation near a point of marginal stability or the use of any batteries or integrated circuits.
- 8 December 2022
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 22 (24) , 9831-9838
Nonlinear Stiffness and Nonlinear Damping in Atomically Thin MoS2 Nanomechanical Resonators
We report on experimental measurements and quantitative analyses of nonlinear dynamic characteristics in ultimately thin nanomechanical resonators built upon single-layer, bilayer, and trilayer (1L, 2L, and 3L) molybdenum disulfide (MoS2) vibrating drumhead membranes. This synergistic study with calibrated measurements and analytical modeling on observed nonlinear responses has led to the determination of nonlinear damping and stiffness coefficients at cubic and quintic orders for these two-dimensional (2D) resonators operating in the very high frequency (VHF) band (up to ∼90 MHz). We find that the quintic force can be ∼20% of the Duffing force at larger amplitudes, and thus, it generally cannot be ignored in a nonlinear dynamics analysis. This study provides the first quantification of nonlinear damping and frequency detuning characteristics in 2D semiconductor nanomechanical resonators and elucidates their origins and dependency on engineerable parameters, setting a foundation for future exploration and utilization of the rich nonlinear dynamics in 2D nanomechanical systems.
- 8 December 2022
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 22 (24) , 9831-9838
Nonlinear Stiffness and Nonlinear Damping in Atomically Thin MoS2 Nanomechanical Resonators
We report on experimental measurements and quantitative analyses of nonlinear dynamic characteristics in ultimately thin nanomechanical resonators built upon single-layer, bilayer, and trilayer (1L, 2L, and 3L) molybdenum disulfide (MoS2) vibrating drumhead membranes. This synergistic study with calibrated measurements and analytical modeling on observed nonlinear responses has led to the determination of nonlinear damping and stiffness coefficients at cubic and quintic orders for these two-dimensional (2D) resonators operating in the very high frequency (VHF) band (up to ∼90 MHz). We find that the quintic force can be ∼20% of the Duffing force at larger amplitudes, and thus, it generally cannot be ignored in a nonlinear dynamics analysis. This study provides the first quantification of nonlinear damping and frequency detuning characteristics in 2D semiconductor nanomechanical resonators and elucidates their origins and dependency on engineerable parameters, setting a foundation for future exploration and utilization of the rich nonlinear dynamics in 2D nanomechanical systems.
- 23 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (4) , 1658-1666
Voltage-Controlled Energy-Efficient Domain Wall Synapses With Stochastic Distribution of Quantized Weights in the Presence of Thermal Noise and Edge Roughness
We propose energy-efficient voltage-induced strain control of a domain wall (DW) in a perpendicularly magnetized nanoscale racetrack on a piezoelectric substrate that can implement a multistate synapse to be utilized in neuromorphic computing platforms. Here, strain generated in the piezoelectric is mechanically transferred to the racetrack and modulates the perpendicular magnetic anisotropy (PMA) in a system that has significant interfacial Dzyaloshinskii–Moriya interaction (DMI). When different voltages are applied (i.e., different strains are generated) in conjunction with spin–orbit torque (SOT) due to a fixed current flowing in the heavy metal layer for a fixed time, DWs are translated to different distances and implement different synaptic weights. We have shown using micromagnetic simulations that five-state and three-state synapses can be implemented in a racetrack that is modeled with the inclusion of natural edge roughness and room temperature thermal noise. These simulations show interesting dynamics of DWs due to interaction with roughness-induced pinning sites. Thus, notches need not be fabricated to implement multistate nonvolatile synapses. Such a strain-controlled synapse has an energy consumption of ~1 fJ and could thus be very attractive to implement energy-efficient quantized neural networks, which has been shown recently to achieve near equivalent classification accuracy to the full-precision neural networks.
- 23 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (4) , 1658-1666
Voltage-Controlled Energy-Efficient Domain Wall Synapses With Stochastic Distribution of Quantized Weights in the Presence of Thermal Noise and Edge Roughness
We propose energy-efficient voltage-induced strain control of a domain wall (DW) in a perpendicularly magnetized nanoscale racetrack on a piezoelectric substrate that can implement a multistate synapse to be utilized in neuromorphic computing platforms. Here, strain generated in the piezoelectric is mechanically transferred to the racetrack and modulates the perpendicular magnetic anisotropy (PMA) in a system that has significant interfacial Dzyaloshinskii–Moriya interaction (DMI). When different voltages are applied (i.e., different strains are generated) in conjunction with spin–orbit torque (SOT) due to a fixed current flowing in the heavy metal layer for a fixed time, DWs are translated to different distances and implement different synaptic weights. We have shown using micromagnetic simulations that five-state and three-state synapses can be implemented in a racetrack that is modeled with the inclusion of natural edge roughness and room temperature thermal noise. These simulations show interesting dynamics of DWs due to interaction with roughness-induced pinning sites. Thus, notches need not be fabricated to implement multistate nonvolatile synapses. Such a strain-controlled synapse has an energy consumption of ~1 fJ and could thus be very attractive to implement energy-efficient quantized neural networks, which has been shown recently to achieve near equivalent classification accuracy to the full-precision neural networks.
- 3 June 2021
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 129 (21) , 214505
Modeling of magnetization dynamics and thermal magnetic moment fluctuations in nanoparticle-enhanced magnetic resonance detection
This study presents a systematic numerical modeling investigation of magnetization dynamics and thermal magnetic moment fluctuations of single magnetic domain nanoparticles in a configuration applicable to enhancing inductive magnetic resonance detection signal to noise ratio (SNR). Previous proposals for oriented anisotropic single magnetic domain nanoparticle amplification of magnetic flux in a magnetic resonance imaging (MRI) coil focused only on the coil pick-up voltage signal enhancement. In this study, the numerical evaluation of the SNR has been extended by modeling the inherent thermal magnetic noise introduced into the detection coil by the insertion of such anisotropic nanoparticle-filled coil core. The Landau–Lifshitz–Gilbert equation under the Stoner–Wohlfarth single magnetic domain (macrospin) assumption was utilized to simulate the magnetization dynamics due to AC drive field as well as thermal noise. These simulations are used to evaluate the nanoparticle configurations and shape effects on enhancing SNR. Finally, we explore the effect of narrow band filtering of the broadband magnetic moment thermal fluctuation noise on the SNR. It was observed that for a particular shape of a single nanoparticle, the SNR could be increased up to ∼8 and the choice of an appropriate number of the nanoparticles increases the SNR by several orders of magnitude and could consequently lead to the detectability of a very small field of ∼10 pT. These results could provide an impetus for relatively simple modifications to existing MRI systems for achieving enhanced detection SNR in scanners with modest polarizing magnetic fields.
- 3 June 2021
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 129 (21) , 214505
Modeling of magnetization dynamics and thermal magnetic moment fluctuations in nanoparticle-enhanced magnetic resonance detection
This study presents a systematic numerical modeling investigation of magnetization dynamics and thermal magnetic moment fluctuations of single magnetic domain nanoparticles in a configuration applicable to enhancing inductive magnetic resonance detection signal to noise ratio (SNR). Previous proposals for oriented anisotropic single magnetic domain nanoparticle amplification of magnetic flux in a magnetic resonance imaging (MRI) coil focused only on the coil pick-up voltage signal enhancement. In this study, the numerical evaluation of the SNR has been extended by modeling the inherent thermal magnetic noise introduced into the detection coil by the insertion of such anisotropic nanoparticle-filled coil core. The Landau–Lifshitz–Gilbert equation under the Stoner–Wohlfarth single magnetic domain (macrospin) assumption was utilized to simulate the magnetization dynamics due to AC drive field as well as thermal noise. These simulations are used to evaluate the nanoparticle configurations and shape effects on enhancing SNR. Finally, we explore the effect of narrow band filtering of the broadband magnetic moment thermal fluctuation noise on the SNR. It was observed that for a particular shape of a single nanoparticle, the SNR could be increased up to ∼8 and the choice of an appropriate number of the nanoparticles increases the SNR by several orders of magnitude and could consequently lead to the detectability of a very small field of ∼10 pT. These results could provide an impetus for relatively simple modifications to existing MRI systems for achieving enhanced detection SNR in scanners with modest polarizing magnetic fields.
- 14 December 2020
- Published by AIP Publishing in Applied Physics Letters
- Vol. 117 (24) , 243504
Electromechanical coupling and motion transduction in β -Ga2O3 vibrating channel transistors
We report on device physics modeling, assisted by experimental measurement results, for all-electronic transduction of resonant electromechanical motion of nanoscale β-Ga2O3 vibrating channel transistors (VCTs), including both direct readout of high frequency transmission current (without frequency down-conversion) and frequency modulation (FM) down-conversion techniques. The β-Ga2O3 VCTs under consideration have fundamental mode resonance frequencies at ∼25 MHz–1 GHz, with quality factors (Qs) of ∼100–5000 and transconductance gm at ∼0.2 nS–5 μS. In analysis of signal transduction with varying device parameters, the transistor's gate trench depth z0 and transconductance gm play key roles in improving the electromechanical coupling and device performance. Reduction of trench depth z0 can engender a major enhancement in readout current. Reducing channel thickness h and increasing channel length L can improve the readout current while downshifting the resonance frequency at the same time. We design β-Ga2O3 VCT with a suspended modulation doped field effect transistor structure for efficient operation in the GHz range. This study paves the way for future engineering of all-electronic transduction and integration of high frequency β-Ga2O3 resonators on chip with β-Ga2O3 electronics and optoelectronics.
- 14 December 2020
- Published by AIP Publishing in Applied Physics Letters
- Vol. 117 (24) , 243504
Electromechanical coupling and motion transduction in β -Ga2O3 vibrating channel transistors
We report on device physics modeling, assisted by experimental measurement results, for all-electronic transduction of resonant electromechanical motion of nanoscale β-Ga2O3 vibrating channel transistors (VCTs), including both direct readout of high frequency transmission current (without frequency down-conversion) and frequency modulation (FM) down-conversion techniques. The β-Ga2O3 VCTs under consideration have fundamental mode resonance frequencies at ∼25 MHz–1 GHz, with quality factors (Qs) of ∼100–5000 and transconductance gm at ∼0.2 nS–5 μS. In analysis of signal transduction with varying device parameters, the transistor's gate trench depth z0 and transconductance gm play key roles in improving the electromechanical coupling and device performance. Reduction of trench depth z0 can engender a major enhancement in readout current. Reducing channel thickness h and increasing channel length L can improve the readout current while downshifting the resonance frequency at the same time. We design β-Ga2O3 VCT with a suspended modulation doped field effect transistor structure for efficient operation in the GHz range. This study paves the way for future engineering of all-electronic transduction and integration of high frequency β-Ga2O3 resonators on chip with β-Ga2O3 electronics and optoelectronics.