Junjia Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Junjia Zhang has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Cunlei Zou3 shared publications
Jisen Zheng
3 shared publications- Shichao Liu
School of Iron and Steel, Soochow University, Suzhou 215021, China
3 shared publications Xin Chen
3 shared publicationsYing Fu
3 shared publicationsJinchuan Jie
School of Materials Science and Engineering, Dalian University of Technology, Dalian, 116024, PR China
2 shared publications
Latest Publications
- Open Access
- 20 October 2026
- Published by Elsevier in SSRN Electronic Journal
Effects of Sn on microstructural evolution and physical property of Cu-Fe-P alloy
The Cu-2.23Fe-0.03P-xSn (wt. %, x=0, 0.1, 0.3, 0.5) alloys were prepared by vacuum melting, and the effect of Sn on microstructural evolutions was systematically investigated, as well as the physical property. The increase of Sn content had a significant refinement effect on alloy structures, and this effect could be maintained throughout the entire process, namely solid-solution, hot-rolling, annealing, cold-rolling and aging. There appeared a distinct bimodal characteristic on the alloy mechanical properties during aging process, it could be attributed to the structure transformation of Fe precipitated phase from FCC to BCC, which introduced large amounts of dislocations into the adjacent micro-region and interacted with the precipitated phase. This bimodal characteristic became more pronounced with the Sn addition, due to the fact that Ⅰ. Sn promoted the refinement of precipitated phases, Ⅱ. Sn was enriched at the matrix-precipitate interfaces, and thereby both promoting the dislocation multiplication. The appropriate addition of Sn atoms, mainly existing in the solid solution form, would significantly improve the mechanical properties of as-aged alloys, resulting in a better balance between UTS and conductivity for (488 MPa + 55 %IACS) and (509 MPa + 48 %IACS), furthermore the softening temperature was meanwhile increased for 125 K.
- 20 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffects of Sn on microstructural evolution and physical property of Cu-Fe-P alloy
The Cu-2.23Fe-0.03P-xSn (wt. %, x=0, 0.1, 0.3, 0.5) alloys were prepared by vacuum melting, and the effect of Sn on microstructural evolutions was systematically investigated, as well as the physical property. The increase of Sn content had a significant refinement effect on alloy structures, and this effect could be maintained throughout the entire process, namely solid-solution, hot-rolling, annealing, cold-rolling and aging. There appeared a distinct bimodal characteristic on the alloy mechanical properties during aging process, it could be attributed to the structure transformation of Fe precipitated phase from FCC to BCC, which introduced large amounts of dislocations into the adjacent micro-region and interacted with the precipitated phase. This bimodal characteristic became more pronounced with the Sn addition, due to the fact that Ⅰ. Sn promoted the refinement of precipitated phases, Ⅱ. Sn was enriched at the matrix-precipitate interfaces, and thereby both promoting the dislocation multiplication. The appropriate addition of Sn atoms, mainly existing in the solid solution form, would significantly improve the mechanical properties of as-aged alloys, resulting in a better balance between UTS and conductivity for (488 MPa + 55 %IACS) and (509 MPa + 48 %IACS), furthermore the softening temperature was meanwhile increased for 125 K.
- Open Access
- 19 May 2026
- Published by Elsevier in SSRN Electronic Journal
Effects of Si content on precipitation behavior and physical property of Cu-Ni-Co-Si alloy
The Cu-1.8Ni-0.9Co-xSi alloys with different Si content (Si/(Co+Ni) =1/6, 2/6, 3/6 and 4/6, atomic ratio) were prepared by vacuum melting, and their microstructural evolutions were systematically investigated, as well as the physical property. The increase of Si content had a significant refinement effect on alloy structures, and this effect could be maintained throughout the entire process, namely solid-solution, hot-rolling, annealing, cold-rolling and aging. Two different morphologies of (Ni,Co)2Si phases were present in the as-cast structure: one was the granular-shaped segregation phase at grain boundary, and the other was the disc-shaped precipitated phase inside grain. They completely dissolved into the matrix during solution, and then re-precipitated into the nano-scale (Ni,Co)2Si phases during aging, which would effectively hinder the dislocation movement through the bypassing mechanism. The Si content increasing would promote this beneficial precipitation behavior, but severely damage the electrical conductivity once excess. The optimal property was obtained for alloy, owing an appropriate Si content of 0.427-0.641 wt.%, and aged at 723 K for 40-240 min (electrical conductivity >43 %IACS, hardness >253.0 HV, UTS >784.2 MPa). The precipitation kinetics equation was also obtained, and it kept in good agreements with the experimental values, for an error of less than 1%.
- 19 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffects of Si content on precipitation behavior and physical property of Cu-Ni-Co-Si alloy
The Cu-1.8Ni-0.9Co-xSi alloys with different Si content (Si/(Co+Ni) =1/6, 2/6, 3/6 and 4/6, atomic ratio) were prepared by vacuum melting, and their microstructural evolutions were systematically investigated, as well as the physical property. The increase of Si content had a significant refinement effect on alloy structures, and this effect could be maintained throughout the entire process, namely solid-solution, hot-rolling, annealing, cold-rolling and aging. Two different morphologies of (Ni,Co)2Si phases were present in the as-cast structure: one was the granular-shaped segregation phase at grain boundary, and the other was the disc-shaped precipitated phase inside grain. They completely dissolved into the matrix during solution, and then re-precipitated into the nano-scale (Ni,Co)2Si phases during aging, which would effectively hinder the dislocation movement through the bypassing mechanism. The Si content increasing would promote this beneficial precipitation behavior, but severely damage the electrical conductivity once excess. The optimal property was obtained for alloy, owing an appropriate Si content of 0.427-0.641 wt.%, and aged at 723 K for 40-240 min (electrical conductivity >43 %IACS, hardness >253.0 HV, UTS >784.2 MPa). The precipitation kinetics equation was also obtained, and it kept in good agreements with the experimental values, for an error of less than 1%.
- 28 June 2025
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 20 (3) , 1700-1711
Corrosion Resistance of 9CrMoCoB Cast Steel: Role of B-Containing M23(C,B)6 Carbide Precipitation
- 28 June 2025
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 20 (3) , 1700-1711
Corrosion Resistance of 9CrMoCoB Cast Steel: Role of B-Containing M23(C,B)6 Carbide Precipitation
- Open Access
Spontaneous Infiltration Behavior of Al Matrix into Carbon Fiber Bundles Induced by Al-Ni Binary Reaction
In this study, a Ni-coated carbon fiber reinforced Al-matrix (Ni-CF/Al) composite is prepared utilizing a pressure-free infiltration process. The CFs are coated with a layer of Ni through an electroless plating process, which facilitates the spontaneous infiltration behavior driven by the Al-Ni binary reaction. The spontaneous infiltration process, observed via synchrotron radiation in the direction opposite to gravity, demonstrates a fastest velocity of 31.02 ± 1.08 μm/s. By increasing the infiltration temperature, the interfacial microstructure of the composite can be enhanced, characterized by a reduction in un-infiltrated defects and promoted by the interfacial Al-Ni reaction. Notably, large-size Al-Ni intermetallic compounds (IMCs) at the interface are replaced by fine (Al+Al3Ni) eutectic structure, given an optimal fabrication temperature of 720 °C. This contributes to a significantly enhanced ultimate tensile strength (UTS) of the composite, reaching a maximum of 135 ± 4 MPa, which is 159.6% higher than that of the matrix.
Open AccessSpontaneous Infiltration Behavior of Al Matrix into Carbon Fiber Bundles Induced by Al-Ni Binary Reaction
In this study, a Ni-coated carbon fiber reinforced Al-matrix (Ni-CF/Al) composite is prepared utilizing a pressure-free infiltration process. The CFs are coated with a layer of Ni through an electroless plating process, which facilitates the spontaneous infiltration behavior driven by the Al-Ni binary reaction. The spontaneous infiltration process, observed via synchrotron radiation in the direction opposite to gravity, demonstrates a fastest velocity of 31.02 ± 1.08 μm/s. By increasing the infiltration temperature, the interfacial microstructure of the composite can be enhanced, characterized by a reduction in un-infiltrated defects and promoted by the interfacial Al-Ni reaction. Notably, large-size Al-Ni intermetallic compounds (IMCs) at the interface are replaced by fine (Al+Al3Ni) eutectic structure, given an optimal fabrication temperature of 720 °C. This contributes to a significantly enhanced ultimate tensile strength (UTS) of the composite, reaching a maximum of 135 ± 4 MPa, which is 159.6% higher than that of the matrix.
- Open Access
- 21 May 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 30, 7998-8005
Study on Ni/P-coating deposition and interface behavior in solid-solid/solid-liquid compositing process
- 21 May 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 30, 7998-8005
Open AccessStudy on Ni/P-coating deposition and interface behavior in solid-solid/solid-liquid compositing process
- 28 March 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 899
Effect of Hf addition on structural transformation and aging stability of Cu–15Ni–8Sn alloy
- 28 March 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 899
Effect of Hf addition on structural transformation and aging stability of Cu–15Ni–8Sn alloy
- Open Access
- 26 April 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 24, 6484-6494
Microstructure evolution, diffusion behavior, and mechanical properties of a Cu/AlCoCrFeNi2.1 composite under pulsed magnetic field
- 26 April 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 24, 6484-6494
Open AccessMicrostructure evolution, diffusion behavior, and mechanical properties of a Cu/AlCoCrFeNi2.1 composite under pulsed magnetic field
- 14 February 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 868, 144777
Effect of defect strengthening on the mechanical properties of a novel Cu–15Ni–8Sn alloy
- 14 February 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 868, 144777
Effect of defect strengthening on the mechanical properties of a novel Cu–15Ni–8Sn alloy
- 1 February 2022
- Published by Elsevier in Materials Letters
- Vol. 309, 131340
Accelerated design eutectic-high-entropy-alloys using simple empirical rules
- 1 February 2022
- Published by Elsevier in Materials Letters
- Vol. 309, 131340
Accelerated design eutectic-high-entropy-alloys using simple empirical rules
- Open Access
- 1 March 2021
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 11, 197-210
Fabrication of carbon fibers reinforced Al-matrix composites in pulsed magnetic field
- 1 March 2021
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 11, 197-210
Open AccessFabrication of carbon fibers reinforced Al-matrix composites in pulsed magnetic field