Shichao Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shichao Liu has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Yong Dong
Innovation & Interdisciplinary Institute of Low Carbon Metallurgical Engineering (School of Materials and Energy), Guangdong University of Technology, Guangzhou, China
5 shared publications Jinchuan Jie
4 shared publications- Junjia Zhang
School of Materials Science and Engineering, Northeastern University, Shenyang, China
3 shared publications Bowen Dong
2 shared publications- Chuanqiang Li
School of Materials and Energy, Guangdong University of Technology, Guangzhou, China
2 shared publications Songsong Xu
2 shared publications
Latest Publications
- 20 December 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 952
Effect of Nb addition on microstructures, mechanical and electrical properties of Cu-15Ni-8Sn alloy
- 20 December 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 952
Effect of Nb addition on microstructures, mechanical and electrical properties of Cu-15Ni-8Sn alloy
- Open Access
Unveiling the Role of Graphite Morphology in Ductile Iron: A 3D FEM-Based Micromechanical Framework for Damage Evolution and Mechanical Performance Prediction with Applicability to Multiphase Alloys
The mechanical performance of cast iron is strongly governed by the morphology of its graphite phase, yet establishing a quantitative link between microstructure and macroscopic properties remains a challenge. In this study, a three-dimensional finite element method (FEM)-based micromechanical framework is proposed to analyze and predict the mechanical behavior of cast iron with representative graphite morphologies, spheroidal and flake graphite. Realistic representative volume elements (RVEs) are reconstructed based on experimental microstructural characterization and literature-based X-ray computed tomography data, ensuring geometric fidelity and statistical representativeness. Cohesive zone modeling (CZM) is implemented at the graphite/matrix interface and within the graphite phase to simulate interfacial debonding and brittle fracture, respectively. Full-field simulations of plastic strain and stress evolution under uniaxial tensile loading reveal that spheroidal graphite promotes uniform deformation, delayed damage initiation, and enhanced ductility through effective stress distribution and progressive plastic flow. In contrast, flake graphite induces severe stress concentration at sharp tips, leading to early microcrack nucleation and rapid crack propagation along the flake planes, resulting in brittle-like failure. The simulated stress–strain responses and failure modes are consistent with experimental observations, validating the predictive capability of the model. This work establishes a microstructure–property relationship in multiphase alloys through a physics-informed computational approach, demonstrating the potential of FEM-based modeling as a powerful tool for performance prediction and microstructure-guided design of cast iron and other heterogeneous materials.
Open AccessUnveiling the Role of Graphite Morphology in Ductile Iron: A 3D FEM-Based Micromechanical Framework for Damage Evolution and Mechanical Performance Prediction with Applicability to Multiphase Alloys
The mechanical performance of cast iron is strongly governed by the morphology of its graphite phase, yet establishing a quantitative link between microstructure and macroscopic properties remains a challenge. In this study, a three-dimensional finite element method (FEM)-based micromechanical framework is proposed to analyze and predict the mechanical behavior of cast iron with representative graphite morphologies, spheroidal and flake graphite. Realistic representative volume elements (RVEs) are reconstructed based on experimental microstructural characterization and literature-based X-ray computed tomography data, ensuring geometric fidelity and statistical representativeness. Cohesive zone modeling (CZM) is implemented at the graphite/matrix interface and within the graphite phase to simulate interfacial debonding and brittle fracture, respectively. Full-field simulations of plastic strain and stress evolution under uniaxial tensile loading reveal that spheroidal graphite promotes uniform deformation, delayed damage initiation, and enhanced ductility through effective stress distribution and progressive plastic flow. In contrast, flake graphite induces severe stress concentration at sharp tips, leading to early microcrack nucleation and rapid crack propagation along the flake planes, resulting in brittle-like failure. The simulated stress–strain responses and failure modes are consistent with experimental observations, validating the predictive capability of the model. This work establishes a microstructure–property relationship in multiphase alloys through a physics-informed computational approach, demonstrating the potential of FEM-based modeling as a powerful tool for performance prediction and microstructure-guided design of cast iron and other heterogeneous materials.
- Open Access
Growth Behavior of Multi-Element Compound Layers During Reactive Diffusion Between Solid CoCrFeMnNi Alloy and Liquid Al
In the present study, the diffusion couple of solid CoCrFeMnNi HEA and liquid pure Al was prepared. The microstructure evolution and relevant interdiffusion behavior of CoCrFeMnNi HEA/Al solid–liquid diffusion couple processed by different parameters were characterized and investigated. Results demonstrated that the interfacial compounds in the order of Al(Co, Cr, Fe, Mn, Ni), Al13(Co, Cr, Fe, Mn, Ni)4 and Al4(Co, Cr, Fe, Mn, Ni) were determined in the interdiffusion area along the direction from CoCrFeMnNi HEA to Al, and the precipitated Al4(Cr, Mn) and Al9(Co, Fe, Ni) phases were formed in the center of Al couple. In addition, the diffusion mechanism and activation energy of growth for each diffusion layer were revealed and determined. More importantly, the growth mechanism of each diffusion layer was also investigated and uncovered in detail. Meanwhile, the activation energy of each intermetallic layer was obtained by the Arrhenius equation and the linear regression method. It is anticipated that this present study would provide a fundamental understanding and theoretical basis for the high-entropy alloy CoCrFeMnNi HEA, potentially applied as the cast mold material for cast aluminum alloy.
Open AccessGrowth Behavior of Multi-Element Compound Layers During Reactive Diffusion Between Solid CoCrFeMnNi Alloy and Liquid Al
In the present study, the diffusion couple of solid CoCrFeMnNi HEA and liquid pure Al was prepared. The microstructure evolution and relevant interdiffusion behavior of CoCrFeMnNi HEA/Al solid–liquid diffusion couple processed by different parameters were characterized and investigated. Results demonstrated that the interfacial compounds in the order of Al(Co, Cr, Fe, Mn, Ni), Al13(Co, Cr, Fe, Mn, Ni)4 and Al4(Co, Cr, Fe, Mn, Ni) were determined in the interdiffusion area along the direction from CoCrFeMnNi HEA to Al, and the precipitated Al4(Cr, Mn) and Al9(Co, Fe, Ni) phases were formed in the center of Al couple. In addition, the diffusion mechanism and activation energy of growth for each diffusion layer were revealed and determined. More importantly, the growth mechanism of each diffusion layer was also investigated and uncovered in detail. Meanwhile, the activation energy of each intermetallic layer was obtained by the Arrhenius equation and the linear regression method. It is anticipated that this present study would provide a fundamental understanding and theoretical basis for the high-entropy alloy CoCrFeMnNi HEA, potentially applied as the cast mold material for cast aluminum alloy.
- Open Access
Microstructure Evolution and Mechanical Properties of Dual-Phase AlCrFe2Ni2 High-Entropy Alloy Under High-Strain-Rate Compression
This paper investigates the effect of strain rate on the mechanical deformation and microstructural development of dual-phase AlCrFe2Ni2 high-entropy alloy during quasi-static and dynamic compression processes. It is revealed that the as-cast AlCrFe2Ni2 alloy is composed of a mixture of FCC, disordered BCC, and ordered B2 crystal structure phases. The alloy shows excellent compressive properties under quasi-static and dynamic deformation. The yield strength exceeds 600 MPa while the compressive strength is more than 3000 MPa at the compression rates of 30% under quasi-static conditions. Under dynamic compression conditions, the ultimate compression stresses are 1522 MPa, 1816 MPa, and 1925 MPa with compression strains about 12.8%, 14.7%, and 18.2% at strain rates of 1300 s−1, 1700 s−1 and 2100 s−1, respectively. The dynamic yield strength is approximately linear with strain rate within the specified range and exhibit great sensitivity. The strong localized deformation regions (i.e., adiabatic shear bands (ASBs)) appear in dynamically deformed samples by dynamic recrystallization due to the conflicting processes of strain rate hardening and heat softening.
Open AccessMicrostructure Evolution and Mechanical Properties of Dual-Phase AlCrFe2Ni2 High-Entropy Alloy Under High-Strain-Rate Compression
This paper investigates the effect of strain rate on the mechanical deformation and microstructural development of dual-phase AlCrFe2Ni2 high-entropy alloy during quasi-static and dynamic compression processes. It is revealed that the as-cast AlCrFe2Ni2 alloy is composed of a mixture of FCC, disordered BCC, and ordered B2 crystal structure phases. The alloy shows excellent compressive properties under quasi-static and dynamic deformation. The yield strength exceeds 600 MPa while the compressive strength is more than 3000 MPa at the compression rates of 30% under quasi-static conditions. Under dynamic compression conditions, the ultimate compression stresses are 1522 MPa, 1816 MPa, and 1925 MPa with compression strains about 12.8%, 14.7%, and 18.2% at strain rates of 1300 s−1, 1700 s−1 and 2100 s−1, respectively. The dynamic yield strength is approximately linear with strain rate within the specified range and exhibit great sensitivity. The strong localized deformation regions (i.e., adiabatic shear bands (ASBs)) appear in dynamically deformed samples by dynamic recrystallization due to the conflicting processes of strain rate hardening and heat softening.
- Open Access
Spontaneous Infiltration Behavior of Al Matrix into Carbon Fiber Bundles Induced by Al-Ni Binary Reaction
In this study, a Ni-coated carbon fiber reinforced Al-matrix (Ni-CF/Al) composite is prepared utilizing a pressure-free infiltration process. The CFs are coated with a layer of Ni through an electroless plating process, which facilitates the spontaneous infiltration behavior driven by the Al-Ni binary reaction. The spontaneous infiltration process, observed via synchrotron radiation in the direction opposite to gravity, demonstrates a fastest velocity of 31.02 ± 1.08 μm/s. By increasing the infiltration temperature, the interfacial microstructure of the composite can be enhanced, characterized by a reduction in un-infiltrated defects and promoted by the interfacial Al-Ni reaction. Notably, large-size Al-Ni intermetallic compounds (IMCs) at the interface are replaced by fine (Al+Al3Ni) eutectic structure, given an optimal fabrication temperature of 720 °C. This contributes to a significantly enhanced ultimate tensile strength (UTS) of the composite, reaching a maximum of 135 ± 4 MPa, which is 159.6% higher than that of the matrix.
Open AccessSpontaneous Infiltration Behavior of Al Matrix into Carbon Fiber Bundles Induced by Al-Ni Binary Reaction
In this study, a Ni-coated carbon fiber reinforced Al-matrix (Ni-CF/Al) composite is prepared utilizing a pressure-free infiltration process. The CFs are coated with a layer of Ni through an electroless plating process, which facilitates the spontaneous infiltration behavior driven by the Al-Ni binary reaction. The spontaneous infiltration process, observed via synchrotron radiation in the direction opposite to gravity, demonstrates a fastest velocity of 31.02 ± 1.08 μm/s. By increasing the infiltration temperature, the interfacial microstructure of the composite can be enhanced, characterized by a reduction in un-infiltrated defects and promoted by the interfacial Al-Ni reaction. Notably, large-size Al-Ni intermetallic compounds (IMCs) at the interface are replaced by fine (Al+Al3Ni) eutectic structure, given an optimal fabrication temperature of 720 °C. This contributes to a significantly enhanced ultimate tensile strength (UTS) of the composite, reaching a maximum of 135 ± 4 MPa, which is 159.6% higher than that of the matrix.
- 26 September 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 287
Microstructure evolution and enhanced mechanical properties of CF/Mg composites with optimized fiber/matrix interfacial adhesion
- 26 September 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 287
Microstructure evolution and enhanced mechanical properties of CF/Mg composites with optimized fiber/matrix interfacial adhesion
- 14 February 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 868, 144777
Effect of defect strengthening on the mechanical properties of a novel Cu–15Ni–8Sn alloy
- 14 February 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 868, 144777
Effect of defect strengthening on the mechanical properties of a novel Cu–15Ni–8Sn alloy
- Open Access
Microstructure and Mechanical Properties of the 6 wt% Mn-Doped Martensitic Steel Strengthened by Cu/NiAl Nanoparticles
The microstructure and mechanical properties of 6 wt.% Mn-doped martensitic steel have been investigated through a combination of electron backscatter diffraction (EBSD), transmission electron microscopy (TEM), and small-angle neutron scattering (SANS). The 6 wt.% Mn-doped steel exhibits a yield strength of ~1.83 GPa and an elongation-to-failure of ~7% under peak aging, and the ~853 MPa of precipitation strengthening is much higher than that observed in the 1.5 wt.% and 3 wt.% Mn-doped steels. The steel is composed of α’-martensite and slightly equiaxed α-ferrite together with a high proportion (~62.3%) of low-angle grain boundaries, and 6 wt.% Mn doping and the aging treatment have an effect on the matrix’s microstructure. However, 6 wt.% Mn doping can obviously increase the mean size of the Cu/NiAl nanoparticles by enhancing the chemical driving force of the Mn partitioning on the NiAl nanoparticles, which differs from the refining effect on the nanoparticles in 3 wt.% Mn-doped steels. Furthermore, larger Cu/NiAl nanoparticles can significantly improve the yield strength of martensitic steel through precipitation-strengthening mechanisms.
Open AccessMicrostructure and Mechanical Properties of the 6 wt% Mn-Doped Martensitic Steel Strengthened by Cu/NiAl Nanoparticles
The microstructure and mechanical properties of 6 wt.% Mn-doped martensitic steel have been investigated through a combination of electron backscatter diffraction (EBSD), transmission electron microscopy (TEM), and small-angle neutron scattering (SANS). The 6 wt.% Mn-doped steel exhibits a yield strength of ~1.83 GPa and an elongation-to-failure of ~7% under peak aging, and the ~853 MPa of precipitation strengthening is much higher than that observed in the 1.5 wt.% and 3 wt.% Mn-doped steels. The steel is composed of α’-martensite and slightly equiaxed α-ferrite together with a high proportion (~62.3%) of low-angle grain boundaries, and 6 wt.% Mn doping and the aging treatment have an effect on the matrix’s microstructure. However, 6 wt.% Mn doping can obviously increase the mean size of the Cu/NiAl nanoparticles by enhancing the chemical driving force of the Mn partitioning on the NiAl nanoparticles, which differs from the refining effect on the nanoparticles in 3 wt.% Mn-doped steels. Furthermore, larger Cu/NiAl nanoparticles can significantly improve the yield strength of martensitic steel through precipitation-strengthening mechanisms.
- 12 October 2022
- Published by Elsevier in Acta Metallurgica Sinica (English Letters)
- Vol. 36 (3) , 391-404
Effects of V Addition on Microstructural Evolution and Mechanical Properties of AlCrFe2Ni2 High-Entropy Alloys
- 12 October 2022
- Published by Elsevier in Acta Metallurgica Sinica (English Letters)
- Vol. 36 (3) , 391-404
Effects of V Addition on Microstructural Evolution and Mechanical Properties of AlCrFe2Ni2 High-Entropy Alloys