Qingfen Ma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Qingfen Ma has a total of 68 co-authors. Here are the top co-authors by number of shared publications:
- Hui Lu
Institute of Environment and Plant Protection, Chinese Academy of Tropical Agriculture Sciences, Haikou 571101, China
9 shared publications - Jingru Li
School of Mechanical and Electrical Engineering, Hainan University, Haikou 570228, China
9 shared publications - Zhongye Wu
College of Mechanical and Electrical Engineering, Hainan University, Haikou 570228, China
9 shared publications Shenghui Wang
The Institute of Seawater Desalination and Multipurpose Utilization, MNR 1 , Tianjin 300192
6 shared publicationsJingru Li
Hainan University
5 shared publications- Chengpeng Wang
The Institute of Seawater Desalination and Multipurpose Utilization, MNR 1 , Tianjin 300192
4 shared publications
Latest Publications
- Open Access
- 22 October 2026
- Published by AIP Publishing in International Journal of Fluid Engineering
- Vol. 4 (2)
Analysis of rotor dynamic characteristics in turbine-type energy recovery devices for seawater desalination
As a critical energy-saving component in reverse osmosis desalination systems, turbine-type energy recovery devices require rigorous dynamic stability evaluation. To guarantee the safety and stability of these devices, this study employs free and constrained modal analyses of its rotor components using Ansys Workbench. The critical speeds, natural frequencies, and other pertinent parameters of the rotor under various rotational speeds and material properties are calculated. Additionally, the dynamic characteristics of rotors crafted from polyethylene, gray cast iron, stainless steel, structural steel, and 40Cr are examined. The findings reveal that the first six natural frequencies of the rotor in free mode are nearly zero, with the natural frequencies progressively increasing from the 7th to 12th modes, accompanied by varying degrees of deformation. Under constrained conditions, the modes of a turbine-type energy recovery device exhibit stability and are less susceptible to resonance. As the rotational speed varies, the natural frequencies of the modes gradually increase, with critical speeds emerging solely in the first three modes, specifically 93 336, 1.1786 × 105, and 1.3139 × 105 rpm, respectively. Furthermore, as the density and Young’s modulus of the rotor material increase, the first three critical speeds also exhibit a continuous upward trend. This research provides a foundational design basis for the structural stability of turbine-type energy recovery integrated machines.
- 22 October 2026
- Published by AIP Publishing in International Journal of Fluid Engineering
- Vol. 4 (2)
Open AccessAnalysis of rotor dynamic characteristics in turbine-type energy recovery devices for seawater desalination
As a critical energy-saving component in reverse osmosis desalination systems, turbine-type energy recovery devices require rigorous dynamic stability evaluation. To guarantee the safety and stability of these devices, this study employs free and constrained modal analyses of its rotor components using Ansys Workbench. The critical speeds, natural frequencies, and other pertinent parameters of the rotor under various rotational speeds and material properties are calculated. Additionally, the dynamic characteristics of rotors crafted from polyethylene, gray cast iron, stainless steel, structural steel, and 40Cr are examined. The findings reveal that the first six natural frequencies of the rotor in free mode are nearly zero, with the natural frequencies progressively increasing from the 7th to 12th modes, accompanied by varying degrees of deformation. Under constrained conditions, the modes of a turbine-type energy recovery device exhibit stability and are less susceptible to resonance. As the rotational speed varies, the natural frequencies of the modes gradually increase, with critical speeds emerging solely in the first three modes, specifically 93 336, 1.1786 × 105, and 1.3139 × 105 rpm, respectively. Furthermore, as the density and Young’s modulus of the rotor material increase, the first three critical speeds also exhibit a continuous upward trend. This research provides a foundational design basis for the structural stability of turbine-type energy recovery integrated machines.
- Open Access
- 1 October 2026
- Published by Elsevier in Desalination and Water Treatment
- Vol. 328
Energy-exergy analysis of SWRO desalination adopting energy recovery devices of PX and HTC in an island plant case
- 1 October 2026
- Published by Elsevier in Desalination and Water Treatment
- Vol. 328
Open AccessEnergy-exergy analysis of SWRO desalination adopting energy recovery devices of PX and HTC in an island plant case
- Open Access
- 2 April 2026
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 81
Thermodynamic analysis of coconut shell biomass power generation system based on a combined supercritical CO2 Brayton and organic Rankine cycle
- 2 April 2026
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 81
Open AccessThermodynamic analysis of coconut shell biomass power generation system based on a combined supercritical CO2 Brayton and organic Rankine cycle
- Open Access
Design and Optimization of Wavy Plate-Fin Structures for Continuous Ortho–Para Hydrogen Conversion in Heat Exchangers
Efficient ortho–para hydrogen conversion is essential to suppress spontaneous heat release and boil-off losses during cryogenic liquid hydrogen storage and pre-liquefaction processes. In this study, a novel catalyst-filled wavy plate-fin heat exchanger (CFHE) is proposed to simultaneously enhance heat transfer and ortho–para hydrogen conversion under cryogenic conditions. Compared with conventional straight-fin configurations, the wavy-fin structure introduces controlled flow perturbations and increased specific surface area, thereby intensifying transport processes. Three-dimensional computational fluid dynamics (CFD) simulations, using the SST k–ω turbulence model, coupled with an ortho–para hydrogen conversion kinetic model were performed to quantitatively investigate the effects of key geometric parameters and catalyst loading on hydrogen conversion, heat transfer, and pressure drop within a Reynolds number range of 941–1577 and a temperature range of 35–20 K. Within the same CFHE configuration, the para-hydrogen fraction remains nearly unchanged without catalyst but increases significantly with catalyst loading. However, the catalyst reduces the global average Colburn j-factor by about 25%. Despite higher friction losses, the outlet–inlet temperature difference decreases to about 0.866 times that of the non-catalyst case, indicating improved temperature uniformity. A comprehensive performance index e, integrating heat transfer enhancement, flow resistance, and conversion efficiency, was introduced and optimized using a genetic algorithm. The optimized CFHE achieves an outlet para-hydrogen fraction exceeding 95% of the thermodynamic equilibrium value while maintaining hydrogen entirely in the gaseous phase to avoid catalyst deactivation. Overall, the catalyst-packed wavy channel configuration demonstrates superior conversion efficiency, enhanced thermal uniformity, and improved overall performance compared with straight-fin structures, providing quantitative design guidance for high-performance heat exchangers in cryogenic hydrogen liquefaction systems.
Open AccessDesign and Optimization of Wavy Plate-Fin Structures for Continuous Ortho–Para Hydrogen Conversion in Heat Exchangers
Efficient ortho–para hydrogen conversion is essential to suppress spontaneous heat release and boil-off losses during cryogenic liquid hydrogen storage and pre-liquefaction processes. In this study, a novel catalyst-filled wavy plate-fin heat exchanger (CFHE) is proposed to simultaneously enhance heat transfer and ortho–para hydrogen conversion under cryogenic conditions. Compared with conventional straight-fin configurations, the wavy-fin structure introduces controlled flow perturbations and increased specific surface area, thereby intensifying transport processes. Three-dimensional computational fluid dynamics (CFD) simulations, using the SST k–ω turbulence model, coupled with an ortho–para hydrogen conversion kinetic model were performed to quantitatively investigate the effects of key geometric parameters and catalyst loading on hydrogen conversion, heat transfer, and pressure drop within a Reynolds number range of 941–1577 and a temperature range of 35–20 K. Within the same CFHE configuration, the para-hydrogen fraction remains nearly unchanged without catalyst but increases significantly with catalyst loading. However, the catalyst reduces the global average Colburn j-factor by about 25%. Despite higher friction losses, the outlet–inlet temperature difference decreases to about 0.866 times that of the non-catalyst case, indicating improved temperature uniformity. A comprehensive performance index e, integrating heat transfer enhancement, flow resistance, and conversion efficiency, was introduced and optimized using a genetic algorithm. The optimized CFHE achieves an outlet para-hydrogen fraction exceeding 95% of the thermodynamic equilibrium value while maintaining hydrogen entirely in the gaseous phase to avoid catalyst deactivation. Overall, the catalyst-packed wavy channel configuration demonstrates superior conversion efficiency, enhanced thermal uniformity, and improved overall performance compared with straight-fin structures, providing quantitative design guidance for high-performance heat exchangers in cryogenic hydrogen liquefaction systems.
- Open Access
Stress Characteristics Analysis of Aluminum Brazed Structures (ABS) in Liquid Oxygen Subcoolers Under Liquid Nitrogen Conditions
The liquid oxygen subcooler is a key unit for the deep cooling, storage, and transportation of liquid oxygen. Its frequent start–stop operation under liquid nitrogen bath conditions introduces potential risks to service reliability. This study employs a thermo-structural sequential coupling approach to evaluate the stress behavior of ABS components in a flat plate-fin heat exchanger during the pre-cooling, heat-exchange, and recovery stages. Based on the maximum shear stress (Tresca) criterion, the evolution of principal stresses in the brazed layer under liquid nitrogen bath conditions was analyzed, and a conservative assessment of the material’s fatigue behavior was conducted. The results indicate that the equivalent stress is governed by the third principal stress, originating from the thermal compression effect induced by low-temperature constraint shrinkage. During the heat exchange phase (2700 s), the inlet equivalent stress reached 93.49 MPa, which is below the 258 MPa limit, falling within Region 1. Local stress concentration is primarily driven by thermal loading, with brazing layer thickness, curvature radius, and liquid oxygen pressure serving as key control variables. Under a safety factor of 1.15 (107 MPa), fatigue testing exceeding 1.5 million cycles has confirmed the static safety and operational reliability of the ABS.
Open AccessStress Characteristics Analysis of Aluminum Brazed Structures (ABS) in Liquid Oxygen Subcoolers Under Liquid Nitrogen Conditions
The liquid oxygen subcooler is a key unit for the deep cooling, storage, and transportation of liquid oxygen. Its frequent start–stop operation under liquid nitrogen bath conditions introduces potential risks to service reliability. This study employs a thermo-structural sequential coupling approach to evaluate the stress behavior of ABS components in a flat plate-fin heat exchanger during the pre-cooling, heat-exchange, and recovery stages. Based on the maximum shear stress (Tresca) criterion, the evolution of principal stresses in the brazed layer under liquid nitrogen bath conditions was analyzed, and a conservative assessment of the material’s fatigue behavior was conducted. The results indicate that the equivalent stress is governed by the third principal stress, originating from the thermal compression effect induced by low-temperature constraint shrinkage. During the heat exchange phase (2700 s), the inlet equivalent stress reached 93.49 MPa, which is below the 258 MPa limit, falling within Region 1. Local stress concentration is primarily driven by thermal loading, with brazing layer thickness, curvature radius, and liquid oxygen pressure serving as key control variables. Under a safety factor of 1.15 (107 MPa), fatigue testing exceeding 1.5 million cycles has confirmed the static safety and operational reliability of the ABS.
- 1 July 2025
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 17 (4)
Analysis and optimization of a fuel cell-powered multi-purpose vehicle based on three-dimensional thermal management
This study addresses the thermal management and engine compartment optimization of a hydrogen fuel cell multi-purpose vehicle through three-dimensional simulations. A computational fluid dynamics model for the heat dissipation in the engine compartment was developed based on the original design of the vehicle model, and the cooling components (main radiator, secondary radiator, and cooling fan) were validated with experimental data. Under idle and high-speed conditions, the simulated results of heat dissipation in the engine compartment agreed well with the test data, indicating good reliability. Simulation results also revealed significant thermal issues, including severe heat recirculation under idle conditions and reduced air utilization efficiency at high speeds. To mitigate these issues, optimization strategies were proposed through adjusting internal arrangements and modifying external structures. After optimization, temperatures on the main radiator and secondary radiator surfaces were reduced by 7.1% and 2.1%, and airflow through the main radiator and secondary radiator were increased by 22.85% and 16.1% with airflow utilization efficiency enhanced by 38%. Additionally, the driving resistance and the drag coefficient were also reduced by 21% × 10.8%, indicating smoother airflow outside the engine compartment. This approach provides a valuable methodology for thermal management and future optimization of a hydrogen fuel cell vehicle.
- 1 July 2025
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 17 (4)
Analysis and optimization of a fuel cell-powered multi-purpose vehicle based on three-dimensional thermal management
This study addresses the thermal management and engine compartment optimization of a hydrogen fuel cell multi-purpose vehicle through three-dimensional simulations. A computational fluid dynamics model for the heat dissipation in the engine compartment was developed based on the original design of the vehicle model, and the cooling components (main radiator, secondary radiator, and cooling fan) were validated with experimental data. Under idle and high-speed conditions, the simulated results of heat dissipation in the engine compartment agreed well with the test data, indicating good reliability. Simulation results also revealed significant thermal issues, including severe heat recirculation under idle conditions and reduced air utilization efficiency at high speeds. To mitigate these issues, optimization strategies were proposed through adjusting internal arrangements and modifying external structures. After optimization, temperatures on the main radiator and secondary radiator surfaces were reduced by 7.1% and 2.1%, and airflow through the main radiator and secondary radiator were increased by 22.85% and 16.1% with airflow utilization efficiency enhanced by 38%. Additionally, the driving resistance and the drag coefficient were also reduced by 21% × 10.8%, indicating smoother airflow outside the engine compartment. This approach provides a valuable methodology for thermal management and future optimization of a hydrogen fuel cell vehicle.
- Open Access
- 27 April 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (5) , 873
Optimization Design of Lazy-Wave Dynamic Cable Configuration Based on Machine Learning
The safe and efficient design of dynamic submarine cables is critical for the reliability of floating offshore wind turbines, yet traditional time-domain simulation-based optimization approaches are computationally intensive and time consuming. To address this challenge, this study proposes a closed-loop optimization framework that couples machine learning with intelligent optimization algorithms for a dynamic cable configuration design. A high-fidelity surrogate model based on a backpropagation (BP) neural network was trained to accurately predict cable dynamic responses. Three optimization algorithms—Particle Swarm Optimization (PSO), Ivy Optimization (IVY), and Tornado Optimization (TOC)—were evaluated for their effectiveness in optimizing the arrangement of buoyancy and weight blocks. The TOC algorithm exhibited superior accuracy and convergence stability. Optimization results show an 18.3% reduction in maximum curvature while maintaining allowable effective tension limits. This approach significantly enhances optimization efficiency and provides a viable strategy for the intelligent design of dynamic cable systems. Future work will incorporate platform motions induced by wind turbine operation and explore multi-objective optimization schemes to further improve cable performance.
- 27 April 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (5) , 873
Open AccessOptimization Design of Lazy-Wave Dynamic Cable Configuration Based on Machine Learning
The safe and efficient design of dynamic submarine cables is critical for the reliability of floating offshore wind turbines, yet traditional time-domain simulation-based optimization approaches are computationally intensive and time consuming. To address this challenge, this study proposes a closed-loop optimization framework that couples machine learning with intelligent optimization algorithms for a dynamic cable configuration design. A high-fidelity surrogate model based on a backpropagation (BP) neural network was trained to accurately predict cable dynamic responses. Three optimization algorithms—Particle Swarm Optimization (PSO), Ivy Optimization (IVY), and Tornado Optimization (TOC)—were evaluated for their effectiveness in optimizing the arrangement of buoyancy and weight blocks. The TOC algorithm exhibited superior accuracy and convergence stability. Optimization results show an 18.3% reduction in maximum curvature while maintaining allowable effective tension limits. This approach significantly enhances optimization efficiency and provides a viable strategy for the intelligent design of dynamic cable systems. Future work will incorporate platform motions induced by wind turbine operation and explore multi-objective optimization schemes to further improve cable performance.