WCWenqing Chen

Wenqing Chen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Wenqing Chen has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Study on Influential Mechanism of Trailing Edge Sweep Angle on Aerodynamic Noise of a Centrifugal Air Compressor

    by Shizhong Sun, Yiwei Feng, Ziwen Xing, Minglong Zhou, Wenqing Chen, Chuang Wang, Hanyang Cui

    As the main noise source in the hydrogen fuel cell system, the noise level of the centrifugal air compressor greatly affects the comfort of the hydrogen fuel cell vehicle, and can be effectively reduced by optimizing the trailing edge sweep angle of the blade. In this paper, the computational fluid dynamics model was used to study the influence of the trailing edge sweep angle on the aerodynamic performance and flow characteristics of a centrifugal air compressor for vehicle fuel cells. The Ffowcs Williams–Hawkings equation and the computational fluid dynamics–boundary element coupling method were adopted to calculate the dipole source strength on the surface of the blade and the radiated aerodynamic noise, respectively, under the different trailing edge sweep angles. The results showed that the trailing edge sweep could lead to an increase in pressure ratio as well as isentropic efficiency, and a decrease in the intensity of flow separation. Meanwhile, the sound pressure level of the compressor under each working condition could be effectively reduced by the trailing edge sweep. When the rotation speed was 80,000 r·min−1 and the blade trailing edge sweep angle was 15°, the sound pressure level of the radiated aerodynamic noise was 5.8 dBA lower than that without sweep.

  • Open Access

    Study on Characteristics and Control of Aerodynamic Noise of a High-Speed Centrifugal Air Compressor for Vehicle Fuel Cells

    by Shizhong Sun, Ziwen Xing, Wenqing Chen, Minglong Zhou, Chuang Wang, Hanyang Cui

    As the main noise source in the hydrogen fuel cell system, the noise level of the centrifugal air compressor greatly affects the comfort of the hydrogen fuel cell vehicle. For reducing the noise level of centrifugal air compressors, the noise characteristics and control of a high-speed two-stage compressor prototype are studied in this paper. Firstly, the near-field noise measurement, along with the independent component analysis, is carried out to identify the noise source of the developed compressor. Results showed that the “buzz-saw” noise at the rotating fundamental frequency and its low order harmonic frequency in the aerodynamic noise is prominent in the noise spectrum. Thus, the aerodynamic noise characteristics are predicted and analyzed using the CFD–BEM coupling aeroacoustic calculation model. Based on the analysis results, a noise control method coupling the structure optimization and perforated muffler is proposed. The results show that the sound pressure level of the air compressor at 1 m away from the surface is reduced by 4.1 dBA after the structural optimization. A perforated muffler applied in the pipe system of the air compressor can accomplish a reduction of 5.8 dBA in the sound pressure level of the air compressor by impeding the noise transmission on the path. With the coupled noise control methods above, the sound pressure level of the air compressor is reduced from 78.8 dBA to 68.9 dBA under the rated condition.


  • Development and analysis of novel six-lobe helical rotors for hydrogen fuel cell vehicle roots blowers

    by Dantong Li, Zhilong He, Shizhong Sun, Chuang Wang, Wenqing Chen, Ziwen Xing


  • Minimum clearance technology to improve performance of twin-screw refrigeration compressors by spraying coating on rotors

    by Shizhong Sun, Yanpeng Li, Wenqing Chen, Ziwen Xing, Hua Liu

    During the operating of twin-screw refrigeration compressors, the leakage has a significant influence on the performance of compressors. In this paper, a novel minimum clearance technology that applies the abradable coating to the rotor surface is proposed to lessen the leakage. In order to adapt to the application of the abradable coating, the deformation of rotors during operation is analyzed and a suitable clearance is designed based on the fluid-solid coupling analysis. Then, a suitable coating pre-treated by sandblasting is obtained according to the results of friction coefficient and abradability test. Finally, a prototype is tested and the total efficiency, volumetric efficiency, refrigerating capacity, and COP of the prototype are compared before and after spraying the coating. Test results show that the volumetric efficiency and refrigerating capacity increase significantly after spraying the abradable coating, and the input power decreases slightly. As a result, the COP increases by 6.71% and 7.89% at two nominal operating conditions.


  • Investigation of characteristics of discharge pressure pulsation in a twin-screw refrigeration compressor

    by Wenqing Chen, Xiaokun Wu, Ziwen Xing, Xiaolin Wang

    In this paper, characteristics of discharge pressure pulsation in a twin-screw refrigeration compressor are investigated. A thermodynamic model is developed and validated using data from a comprehensive experimental study. This validated model is then applied to investigate effects of key parameters including condensing temperature, compressor rotational speed, super-feed pressure, part-load operation, and design parameters on the discharge pressure pulsation. The results showed that the discharge pressure pulsation was mainly due to periodic variations of mass and energy flow from the working volumes to the discharge chamber. As the condensing temperature increased or decreased from the design condition, the compressor was in either over- or undercompression leading to an increase in the amplitude of the pressure pulsation. The gas super-feed pressure could increase the pressure pulsation at condensing temperatures below the design value and reduce the pressure pulsation at condensing temperatures above the design value. The analysis also demonstrated that the pressure pulsation was lower at part-load conditions. However, the compressor rotational speed increased both the amplitude and frequency of the pressure pulsation. Theoretical analysis of design parameters indicated that a large discharge volume with a high number of lobes could lower the pressure pulsation. These analyses provide useful information for the compressor design and optimization.