Alper Gunoz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alper Gunoz has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Memduh Kara
Mersin University
10 shared publications - Yusuf Kepir
Faculty 3 Mechanical Engineering, Electrical and Energy Systems, Brandenburg University of Technology Cottbus–Senftenberg (BTU), 03046 Cottbus, Germany
8 shared publications Memduh Kara
Engineering Faculty, Department of Mechanical Engineering, Mersin University, Yenişehir, Mersin, Turkey
4 shared publicationsTolga Coskun
Engineering Faculty, Department of Mechanical Engineering, Mersin University, Yenişehir, Mersin, Turkey
2 shared publications- Umut Ozgur Ozaltay
Mersin Universitesi
2 shared publications - Ahmed Adan Mohamud
Dept. of Civil Eng Mersin Unv Mersin Turkey
1 shared publication
Latest Publications
- 4 June 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (16) , 14951-14965
Effect of Carbon Nanotube‐Modified Epoxy on the GFRP Confinement Performance of Concrete
This study investigated the effect of incorporating 0.3 wt.% carbon nanotubes (CNTs) into the epoxy matrix used in glass‐fiber‐reinforced polymer (GFRP) confinement systems for concrete cylinders. Sixteen concrete specimens, divided into low‐ and normal‐strength groups, were cast. Twelve of them were wrapped with GFRP using either plain or CNT‐modified epoxy and tested under monotonic axial compression. The results showed that the addition of CNT enhanced interfacial bonding, as evidenced by fiber shredding and improved mechanical interlocking with concrete. For specimens with insufficient GFRP overlap (10 mm), CNT yielded modest improvements in the hoop rupture strain and compressive strength but reduced the ultimate axial strain. In low‐strength concrete with an adequate overlap (150 mm), CNT modification unexpectedly decreased the confinement efficiency, causing premature rupture. Conversely, normal‐strength concrete specimens with CNT‐modified epoxy exhibited significant improvements in confinement efficiency, strength, and strain enhancement ratios. Existing analytical models underestimate the performance of CNT‐modified systems, particularly for low‐strength concrete, highlighting the need for CNT‐specific design guidelines. The findings demonstrate the potential of CNT‐enhanced GFRP confinement for structural retrofitting, particularly under moderate confinement ratios, and emphasize the necessity for further research on durability, scalability, and cyclic loading effects.
- 4 June 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (16) , 14951-14965
Effect of Carbon Nanotube‐Modified Epoxy on the GFRP Confinement Performance of Concrete
This study investigated the effect of incorporating 0.3 wt.% carbon nanotubes (CNTs) into the epoxy matrix used in glass‐fiber‐reinforced polymer (GFRP) confinement systems for concrete cylinders. Sixteen concrete specimens, divided into low‐ and normal‐strength groups, were cast. Twelve of them were wrapped with GFRP using either plain or CNT‐modified epoxy and tested under monotonic axial compression. The results showed that the addition of CNT enhanced interfacial bonding, as evidenced by fiber shredding and improved mechanical interlocking with concrete. For specimens with insufficient GFRP overlap (10 mm), CNT yielded modest improvements in the hoop rupture strain and compressive strength but reduced the ultimate axial strain. In low‐strength concrete with an adequate overlap (150 mm), CNT modification unexpectedly decreased the confinement efficiency, causing premature rupture. Conversely, normal‐strength concrete specimens with CNT‐modified epoxy exhibited significant improvements in confinement efficiency, strength, and strain enhancement ratios. Existing analytical models underestimate the performance of CNT‐modified systems, particularly for low‐strength concrete, highlighting the need for CNT‐specific design guidelines. The findings demonstrate the potential of CNT‐enhanced GFRP confinement for structural retrofitting, particularly under moderate confinement ratios, and emphasize the necessity for further research on durability, scalability, and cyclic loading effects.
- 21 November 2025
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 60 (23) , 2165-2180
Durability enhancement in aged composite pipes: Low-velocity impact performance of basalt fiber reinforced polymer modified by graphene nanoplatelets
Composite pipes, widely employed in the transport of natural gas, petroleum, and chemical fluids, are often exposed to low-velocity impact loads compromising structural integrity. Such impacts, coupled with prolonged exposure to environmental factors like water and elevated temperatures, accelerate material degradation. This study aims to evaluate the effectiveness of graphene nanoplatelets (GnPs) in enhancing the impact resistance and long-term durability of basalt fiber reinforced polymer (BFRP) composite pipes under hydrothermal aging conditions. Neat and 0.25 wt.% GnPs reinforced BFRP composite pipes were fabricated via filament winding with a ±55° winding angle. The pipes were hydrothermally aged in water at 80°C for 15, 30, 45, and 60 days, followed by low-velocity impact tests at 20 and 40 J. The results revealed that increasing the energy from 20 to 40 J led to an increase in the maximum contact force by approximately 22% in neat samples and about 35% in GnPs reinforced samples, reflecting the enhanced rigidity and impact resistance provided by GnPs. Hydrothermal aging reduced the maximum contact force in all samples, with the most pronounced reduction after 60 days: neat samples decreased by approximately 57%, whereas GnPs reinforced samples about 21% at 40 J. These results indicate that GnPs mitigate aging-induced loss in impact performance by limiting rigidity reduction and damage propagation. Damage analysis further confirms the beneficial role of GnPs in preserving structural integrity under long-term aging. Overall, these findings highlight the potential of GnPs reinforced BFRP pipes for enhanced durability and impact resistance in industrial applications.
- 21 November 2025
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 60 (23) , 2165-2180
Durability enhancement in aged composite pipes: Low-velocity impact performance of basalt fiber reinforced polymer modified by graphene nanoplatelets
Composite pipes, widely employed in the transport of natural gas, petroleum, and chemical fluids, are often exposed to low-velocity impact loads compromising structural integrity. Such impacts, coupled with prolonged exposure to environmental factors like water and elevated temperatures, accelerate material degradation. This study aims to evaluate the effectiveness of graphene nanoplatelets (GnPs) in enhancing the impact resistance and long-term durability of basalt fiber reinforced polymer (BFRP) composite pipes under hydrothermal aging conditions. Neat and 0.25 wt.% GnPs reinforced BFRP composite pipes were fabricated via filament winding with a ±55° winding angle. The pipes were hydrothermally aged in water at 80°C for 15, 30, 45, and 60 days, followed by low-velocity impact tests at 20 and 40 J. The results revealed that increasing the energy from 20 to 40 J led to an increase in the maximum contact force by approximately 22% in neat samples and about 35% in GnPs reinforced samples, reflecting the enhanced rigidity and impact resistance provided by GnPs. Hydrothermal aging reduced the maximum contact force in all samples, with the most pronounced reduction after 60 days: neat samples decreased by approximately 57%, whereas GnPs reinforced samples about 21% at 40 J. These results indicate that GnPs mitigate aging-induced loss in impact performance by limiting rigidity reduction and damage propagation. Damage analysis further confirms the beneficial role of GnPs in preserving structural integrity under long-term aging. Overall, these findings highlight the potential of GnPs reinforced BFRP pipes for enhanced durability and impact resistance in industrial applications.
- 30 September 2025
- Published by Bitlis Eren Universitesi Fen Bilimleri Dergisi in Bitlis Eren Üniversitesi Fen Bilimleri Dergisi
- Vol. 14 (3) , 1921-1941
Investigation of Physical, Mechanical, and Drilling Machinability Properties of Nanoparticles Reinforced Carbon/Glass Fiber Hybrid Composites
This study aims to investigate the effects of nanoparticle reinforcement, fiber hybridization, and stacking sequences on the mechanical properties and drilling machinability of composite materials. For this purpose, 12-layered polymer composite plates reinforced with graphene nanoplatelets (GnPs) and boron nitride nanoparticles (BNNPs) were produced using the vacuum bagging method. Carbon fiber (CF), glass fiber (GF), and hybrid fiber (HF) with different stacking sequences were used as reinforcements. The samples were subjected to density and hardness measurements, as well as conventional drilling tests. Drilling operations were carried out on a CNC vertical machining center using Ø6.5 mm drills with point angles of 90°, 110°, and 130°, at a constant spindle speed (1000 rpm) and three different feed rates (200, 600, and 1000 mm/min). The results demonstrated that the neat CF specimen exhibited the highest hardness, whereas the incorporation of nanoparticles reduced hardness, with BNNP-reinforced specimens showing the greatest reduction of about 15%. Drilling machinability was significantly enhanced, as evidenced by the reduction in delamination, and the optimum hole diameter (Ø6.48 mm) was achieved in the GF-based composite reinforced with BNNPs using a 130° drill point angle and a feed rate of 200 mm/min. The effects of GnPs and BNNPs on the drilling machinability of fiber-reinforced composites have been investigated only to a limited extent in the literature, and this study provides new insights. These findings may contribute to improving the quality and efficiency of drilling processes in the aerospace and automotive industries.
- 30 September 2025
- Published by Bitlis Eren Universitesi Fen Bilimleri Dergisi in Bitlis Eren Üniversitesi Fen Bilimleri Dergisi
- Vol. 14 (3) , 1921-1941
Investigation of Physical, Mechanical, and Drilling Machinability Properties of Nanoparticles Reinforced Carbon/Glass Fiber Hybrid Composites
This study aims to investigate the effects of nanoparticle reinforcement, fiber hybridization, and stacking sequences on the mechanical properties and drilling machinability of composite materials. For this purpose, 12-layered polymer composite plates reinforced with graphene nanoplatelets (GnPs) and boron nitride nanoparticles (BNNPs) were produced using the vacuum bagging method. Carbon fiber (CF), glass fiber (GF), and hybrid fiber (HF) with different stacking sequences were used as reinforcements. The samples were subjected to density and hardness measurements, as well as conventional drilling tests. Drilling operations were carried out on a CNC vertical machining center using Ø6.5 mm drills with point angles of 90°, 110°, and 130°, at a constant spindle speed (1000 rpm) and three different feed rates (200, 600, and 1000 mm/min). The results demonstrated that the neat CF specimen exhibited the highest hardness, whereas the incorporation of nanoparticles reduced hardness, with BNNP-reinforced specimens showing the greatest reduction of about 15%. Drilling machinability was significantly enhanced, as evidenced by the reduction in delamination, and the optimum hole diameter (Ø6.48 mm) was achieved in the GF-based composite reinforced with BNNPs using a 130° drill point angle and a feed rate of 200 mm/min. The effects of GnPs and BNNPs on the drilling machinability of fiber-reinforced composites have been investigated only to a limited extent in the literature, and this study provides new insights. These findings may contribute to improving the quality and efficiency of drilling processes in the aerospace and automotive industries.
- Open Access
- 9 June 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (11) , 10647-10664
Penetration and Perforation Thresholds of GnPs Reinforced Carbon/Glass Fiber Epoxy Hybrid Composites
Composite materials have found extensive application in advanced sectors, including aerospace, defense, and automotive technologies, thanks to their outstanding mechanical properties. However, their high sensitivity to impact loads remains a major limitation. Low‐energy impacts may lead to internal damages like delamination, matrix cracking, and fiber breakage, while exceeding a certain energy threshold results in penetration and perforation. Low penetration and perforation thresholds in structural composite components pose significant risks to safety and operational performance. Therefore, enhancing not only impact resistance but also penetration and perforation thresholds is crucial for the reliable use of composite materials. This study investigates the penetration and perforation behavior of 12‐layered neat and graphene nanoplatelets (GnPs) reinforced composite laminates, including carbon fiber (CFRP), glass fiber (GFRP), and hybrid fiber reinforced polymer (HFRP) systems with various stacking sequences. The laminates were fabricated using the vacuum bagging method. Low‐velocity impact tests were performed at energy levels ranging from 15 J up to the perforation threshold. The energy profiling method was employed to assess the penetration and perforation thresholds, and the damage mechanisms were examined progressively. Results showed that GnPs reinforcement, fiber hybridization, and stacking sequence modifications increased both thresholds while reducing damage at the same impact energy level.
- 9 June 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (11) , 10647-10664
Open AccessPenetration and Perforation Thresholds of GnPs Reinforced Carbon/Glass Fiber Epoxy Hybrid Composites
Composite materials have found extensive application in advanced sectors, including aerospace, defense, and automotive technologies, thanks to their outstanding mechanical properties. However, their high sensitivity to impact loads remains a major limitation. Low‐energy impacts may lead to internal damages like delamination, matrix cracking, and fiber breakage, while exceeding a certain energy threshold results in penetration and perforation. Low penetration and perforation thresholds in structural composite components pose significant risks to safety and operational performance. Therefore, enhancing not only impact resistance but also penetration and perforation thresholds is crucial for the reliable use of composite materials. This study investigates the penetration and perforation behavior of 12‐layered neat and graphene nanoplatelets (GnPs) reinforced composite laminates, including carbon fiber (CFRP), glass fiber (GFRP), and hybrid fiber reinforced polymer (HFRP) systems with various stacking sequences. The laminates were fabricated using the vacuum bagging method. Low‐velocity impact tests were performed at energy levels ranging from 15 J up to the perforation threshold. The energy profiling method was employed to assess the penetration and perforation thresholds, and the damage mechanisms were examined progressively. Results showed that GnPs reinforcement, fiber hybridization, and stacking sequence modifications increased both thresholds while reducing damage at the same impact energy level.
- Open Access
- 1 January 2025
- Published by Journal of Innovative Engineering and Natural Science in Journal of Innovative Engineering and Natural Science
- Vol. 5 (2) , 838-852
An experimental study on the low energy impact behavior of different number of layer e-glass/epoxy composites
Composite materials are increasingly used in structural applications due to the high strength-to-weight ratio, corrosion resistance, and design flexibility they offer; however, susceptibility to impact damage remains a critical concern, particularly in layered configurations. In the present research, low-velocity impact experiments were performed on 8-layer and 16-layer unidirectional E-glass/epoxy composite plates with [+45/-45/90/0]s and [+45/-45/90/0]2s stacking sequences, which were manufactured using the vacuum-assisted hand lay-up method, at impact energy levels of 10, 20, and 30 J. Findings indicated that a rise in impact energy resulted in an increase in maximum contact force and energy absorption for both 8-layer and 16-layer composite plates, with no noticeable change in bending rigidity. At the same energy level, an increase in the number of layers enhanced the maximum contact force and bending rigidity of the composite plates, whereas displacement and the amount of energy absorbed by the material decreased. For all energy levels, the damage observed in the 8-layer composite plates spread over a wider area compared to the damage in the 16-layer plates.
- 1 January 2025
- Published by Journal of Innovative Engineering and Natural Science in Journal of Innovative Engineering and Natural Science
- Vol. 5 (2) , 838-852
Open AccessAn experimental study on the low energy impact behavior of different number of layer e-glass/epoxy composites
Composite materials are increasingly used in structural applications due to the high strength-to-weight ratio, corrosion resistance, and design flexibility they offer; however, susceptibility to impact damage remains a critical concern, particularly in layered configurations. In the present research, low-velocity impact experiments were performed on 8-layer and 16-layer unidirectional E-glass/epoxy composite plates with [+45/-45/90/0]s and [+45/-45/90/0]2s stacking sequences, which were manufactured using the vacuum-assisted hand lay-up method, at impact energy levels of 10, 20, and 30 J. Findings indicated that a rise in impact energy resulted in an increase in maximum contact force and energy absorption for both 8-layer and 16-layer composite plates, with no noticeable change in bending rigidity. At the same energy level, an increase in the number of layers enhanced the maximum contact force and bending rigidity of the composite plates, whereas displacement and the amount of energy absorbed by the material decreased. For all energy levels, the damage observed in the 8-layer composite plates spread over a wider area compared to the damage in the 16-layer plates.
- 9 December 2024
- Published by SAGE Publications in International Journal of Damage Mechanics
- Vol. 34 (9) , 1488-1509
Damage behavior of functionally graded kevlar/carbon epoxy nanocomposites reinforced with polyamide 6.6 nanofiber and MWCNTs subjected to low-velocity impact
The use of carbon and kevlar fiber-reinforced composite materials continues to grow in high-tech applications such as aerospace engineering. One of the most desired properties in composite structures is a strong interfacial bond between the matrix and the fiber. Nano-material reinforcement is one of the most preferred methods for strengthening the fiber-matrix interfacial bond. In the present research, polyamide 6.6 (PA 6.6) nanofiber and multi-walled carbon nanotubes (MWCNTs) reinforced kevlar fabric (KF), carbon fabric (CF) and epoxy matrix nanocomposite plates were produced by functional grading of these two fabrics. PA 6.6 nanofibers, obtained by electrospinning, were placed between the layers, and 12-layer nanocomposite plates were fabricated using a vacuum-assisted hand lay-up method. In producing MWCNTs reinforced nanocomposite plates, 0.3 wt.% of MWCNTs were added into the epoxy matrix. A comprehensive set of 16 distinct composite plates was manufactured, encompassing unreinforced plates, plates reinforced with MWCNTs, plates reinforced with PA 6.6, and plates reinforced with a combination of PA 6.6 and MWCNTs (PA 6.6-MWCNTs). The impact strengths of the produced composite plates were investigated at energy levels of 20, 40 and 60 J. The effects of reinforcing the composite structure with MWCNTs, PA 6.6, and PA 6.6-MWCNTs, as well as functionally grading KF/CF on impact strength, were investigated in detail. The damages that occurred in the material as a result of the low-velocity impact tests were interpreted by examining the high-resolution camera and optical microscope images. Thus, the nanofiber and nanoparticle reinforcement to composite structure and hybridization effect were evaluated together. With the reinforcement of PA 6.6, MWCNTs and PA 6.6-MWCNTs, the impact strength of the nanocomposite samples increased significantly compared to the unreinforced samples. Moreover, the amount of damage caused by the low-velocity impact test in reinforced samples was significantly reduced.
- 9 December 2024
- Published by SAGE Publications in International Journal of Damage Mechanics
- Vol. 34 (9) , 1488-1509
Damage behavior of functionally graded kevlar/carbon epoxy nanocomposites reinforced with polyamide 6.6 nanofiber and MWCNTs subjected to low-velocity impact
The use of carbon and kevlar fiber-reinforced composite materials continues to grow in high-tech applications such as aerospace engineering. One of the most desired properties in composite structures is a strong interfacial bond between the matrix and the fiber. Nano-material reinforcement is one of the most preferred methods for strengthening the fiber-matrix interfacial bond. In the present research, polyamide 6.6 (PA 6.6) nanofiber and multi-walled carbon nanotubes (MWCNTs) reinforced kevlar fabric (KF), carbon fabric (CF) and epoxy matrix nanocomposite plates were produced by functional grading of these two fabrics. PA 6.6 nanofibers, obtained by electrospinning, were placed between the layers, and 12-layer nanocomposite plates were fabricated using a vacuum-assisted hand lay-up method. In producing MWCNTs reinforced nanocomposite plates, 0.3 wt.% of MWCNTs were added into the epoxy matrix. A comprehensive set of 16 distinct composite plates was manufactured, encompassing unreinforced plates, plates reinforced with MWCNTs, plates reinforced with PA 6.6, and plates reinforced with a combination of PA 6.6 and MWCNTs (PA 6.6-MWCNTs). The impact strengths of the produced composite plates were investigated at energy levels of 20, 40 and 60 J. The effects of reinforcing the composite structure with MWCNTs, PA 6.6, and PA 6.6-MWCNTs, as well as functionally grading KF/CF on impact strength, were investigated in detail. The damages that occurred in the material as a result of the low-velocity impact tests were interpreted by examining the high-resolution camera and optical microscope images. Thus, the nanofiber and nanoparticle reinforcement to composite structure and hybridization effect were evaluated together. With the reinforcement of PA 6.6, MWCNTs and PA 6.6-MWCNTs, the impact strength of the nanocomposite samples increased significantly compared to the unreinforced samples. Moreover, the amount of damage caused by the low-velocity impact test in reinforced samples was significantly reduced.
- Open Access
- 10 June 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (13) , 12481-12494
Impact response of hybrid composites under varying environmental conditions: A comparative study
Composite materials are widely preferred in the aviation, automotive, construction and maritime industries due to their many superior properties. As a result of this widespread use, composite structures are inevitably subjected to various environmental conditions. Various environmental conditions may negatively affect the mechanical performance of the structure, and the structure may become unable to maintain its initial mechanical properties, especially in the face of critical loading, such as low‐velocity impacts. This research investigated the influence of various environmental conditions on the low‐velocity impact strength of composite materials. 12‐layer plate samples with epoxy matrix reinforced with woven glass fabric (GF), woven carbon fabric (CF), and hybrid fabric (HF), where the two fabrics are used together, were produced. Low‐velocity impact tests were conducted to these specimens at 20 and 40 J energy levels. Damages occurring in the material as a result of the low‐velocity impact test were interpreted using high‐resolution camera and optical microscope images. Force‐time and force‐ displacement curves were drawn and interpreted. It was concluded that as the impact energy values increased, the maximum force and displacement values also increased.Highlights: The influence of various environmental conditions to which composite materials may be exposed on the dynamic response of the structure has been investigated. Various environmental conditions significantly affected the composite structure's impact behavior. While glass fabric (GF) composite samples were more affected by the seawater environment, carbon fabric (CF) composite samples were more affected by the HCl environment. Hybrid (HF) composite samples were affected by seawater and HCl in approximately equal amounts.
- 10 June 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (13) , 12481-12494
Open AccessImpact response of hybrid composites under varying environmental conditions: A comparative study
Composite materials are widely preferred in the aviation, automotive, construction and maritime industries due to their many superior properties. As a result of this widespread use, composite structures are inevitably subjected to various environmental conditions. Various environmental conditions may negatively affect the mechanical performance of the structure, and the structure may become unable to maintain its initial mechanical properties, especially in the face of critical loading, such as low‐velocity impacts. This research investigated the influence of various environmental conditions on the low‐velocity impact strength of composite materials. 12‐layer plate samples with epoxy matrix reinforced with woven glass fabric (GF), woven carbon fabric (CF), and hybrid fabric (HF), where the two fabrics are used together, were produced. Low‐velocity impact tests were conducted to these specimens at 20 and 40 J energy levels. Damages occurring in the material as a result of the low‐velocity impact test were interpreted using high‐resolution camera and optical microscope images. Force‐time and force‐ displacement curves were drawn and interpreted. It was concluded that as the impact energy values increased, the maximum force and displacement values also increased.Highlights: The influence of various environmental conditions to which composite materials may be exposed on the dynamic response of the structure has been investigated. Various environmental conditions significantly affected the composite structure's impact behavior. While glass fabric (GF) composite samples were more affected by the seawater environment, carbon fabric (CF) composite samples were more affected by the HCl environment. Hybrid (HF) composite samples were affected by seawater and HCl in approximately equal amounts.
- Open Access
- 5 January 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (5) , 4693-4708
Mechanical behavior of the polyamide 6.6 nanofiber and MWCNT‐reinforced hybrid nanocomposites
The present study examines the influence of polyamide 6.6 (PA 6.6) nanofiber and MWCNTs reinforcements on the mechanical behavior of nanocomposite plates formed by hybridization of carbon fabric (CF) and kevlar fabric (KF). First, PA 6.6 nanofibers were manufactured by electrospinning. The produced nanofibers were placed in the interlaminar of nanocomposite plates. PA 6.6 nanofiber and MWCNT‐reinforced nanocomposite plates consisting of 12 layers were produced by the vacuum bagging method. Tensile, Mode‐II fracture and bending tests were applied to the produced composite plates in accordance with the standards. After the mechanical tests, the nanocomposite plates' macro and micro damage analysis was performed. As a result of the reinforcement of PA 6.6, MWCNTs and PA 6.6‐MWCNTs, the tensile strength, interlaminar fracture toughness and bending strength of the nanocomposite plates significantly enhanced compared to unreinforced samples. In addition, interlaminar crack propagation in reinforced samples became more stable than in the unreinforced sample.Highlights: Investigated the impact of PA 6.6 nanofiber and MWCNT reinforcements on nanocomposite plates formed through CF and KF hybridization. Reinforcement with PA 6.6, MWCNTs, and PA 6.6‐MWCNTs significantly improved tensile strength, interlaminar fracture toughness, and bending strength. Mode‐II interlaminar fracture toughness tests demonstrated enhanced crack propagation stability with PA 6.6 nanofiber and MWCNT reinforcements.
- 5 January 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (5) , 4693-4708
Open AccessMechanical behavior of the polyamide 6.6 nanofiber and MWCNT‐reinforced hybrid nanocomposites
The present study examines the influence of polyamide 6.6 (PA 6.6) nanofiber and MWCNTs reinforcements on the mechanical behavior of nanocomposite plates formed by hybridization of carbon fabric (CF) and kevlar fabric (KF). First, PA 6.6 nanofibers were manufactured by electrospinning. The produced nanofibers were placed in the interlaminar of nanocomposite plates. PA 6.6 nanofiber and MWCNT‐reinforced nanocomposite plates consisting of 12 layers were produced by the vacuum bagging method. Tensile, Mode‐II fracture and bending tests were applied to the produced composite plates in accordance with the standards. After the mechanical tests, the nanocomposite plates' macro and micro damage analysis was performed. As a result of the reinforcement of PA 6.6, MWCNTs and PA 6.6‐MWCNTs, the tensile strength, interlaminar fracture toughness and bending strength of the nanocomposite plates significantly enhanced compared to unreinforced samples. In addition, interlaminar crack propagation in reinforced samples became more stable than in the unreinforced sample.Highlights: Investigated the impact of PA 6.6 nanofiber and MWCNT reinforcements on nanocomposite plates formed through CF and KF hybridization. Reinforcement with PA 6.6, MWCNTs, and PA 6.6‐MWCNTs significantly improved tensile strength, interlaminar fracture toughness, and bending strength. Mode‐II interlaminar fracture toughness tests demonstrated enhanced crack propagation stability with PA 6.6 nanofiber and MWCNT reinforcements.
- Open Access
- 5 October 2023
- Published by Turkish Journal of Engineering in Turkish Journal of Engineering
- Vol. 7 (4) , 314-321
A numerical study on the low-velocity impact response of hybrid composite materials
Composite materials are advanced engineering materials with superior properties to traditional materials. One of the most important disadvantages is the high cost of composite materials. Therefore, producing composite materials from the first to the last stage is a very important process. Homogenization is the most important parameter in production since composites contain more than one material type in their structure. In addition, composite structures are sensitive materials against low-velocity impacts. In this study, the effect of reinforcement material combination and stacking sequence on mechanical properties used in the production of composite materials was investigated by low-velocity impact simulations using LS-DYNA software. The mass of the 12 mm diameter spherical impactor used in the analyzes was determined as 10 kg and low-velocity impact tests were applied at 20 J, 30 J and 40 J energy levels. The composite samples were modeled with 180x100mm dimensions and the contact between the impactor and the sample was made from the center of the composite structure. Numerical analyzes were performed using the Tsai-Wu damage criterion in the LS-DYNA software, and material properties were defined using the "Mat_Enhanced_Composite_Damage (MAT 055)" material card.
- 5 October 2023
- Published by Turkish Journal of Engineering in Turkish Journal of Engineering
- Vol. 7 (4) , 314-321
Open AccessA numerical study on the low-velocity impact response of hybrid composite materials
Composite materials are advanced engineering materials with superior properties to traditional materials. One of the most important disadvantages is the high cost of composite materials. Therefore, producing composite materials from the first to the last stage is a very important process. Homogenization is the most important parameter in production since composites contain more than one material type in their structure. In addition, composite structures are sensitive materials against low-velocity impacts. In this study, the effect of reinforcement material combination and stacking sequence on mechanical properties used in the production of composite materials was investigated by low-velocity impact simulations using LS-DYNA software. The mass of the 12 mm diameter spherical impactor used in the analyzes was determined as 10 kg and low-velocity impact tests were applied at 20 J, 30 J and 40 J energy levels. The composite samples were modeled with 180x100mm dimensions and the contact between the impactor and the sample was made from the center of the composite structure. Numerical analyzes were performed using the Tsai-Wu damage criterion in the LS-DYNA software, and material properties were defined using the "Mat_Enhanced_Composite_Damage (MAT 055)" material card.
- 28 October 2022
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 56 (30) , 4635-4644
Effects of extreme low temperatures on the impact behavior of boron nitride nanofillers added carbon fiber/epoxy composite tubes
This study aims to investigate the low-velocity impact response of boron nitride nanoparticles (BNNPs) added carbon fiber reinforced pipes (CFRPs) at various temperature values. Carbon fiber/epoxy composite specimens with (±55°)3 winding angles were manufactured with the filament winding method. Low-velocity impact tests were performed with a 15 J energy level at five different temperatures between −196°C and 23°C ranges to understand the cryogenic environment effect on BNNP added carbon fiber reinforced tubes and neat carbon fiber reinforced tubes. The force-displacement and contact force-time graphs were attained in consequence of low-velocity impact tests. The damage areas, their size and characteristics were scrutinized both visually and with the aid of a Microscope. The test results showed that when ambiance temperatures decreased, the damage areas considerably increased both filled with BNNP and without BNNP filament wound carbon fiber reinforced tubes.
- 28 October 2022
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 56 (30) , 4635-4644
Effects of extreme low temperatures on the impact behavior of boron nitride nanofillers added carbon fiber/epoxy composite tubes
This study aims to investigate the low-velocity impact response of boron nitride nanoparticles (BNNPs) added carbon fiber reinforced pipes (CFRPs) at various temperature values. Carbon fiber/epoxy composite specimens with (±55°)3 winding angles were manufactured with the filament winding method. Low-velocity impact tests were performed with a 15 J energy level at five different temperatures between −196°C and 23°C ranges to understand the cryogenic environment effect on BNNP added carbon fiber reinforced tubes and neat carbon fiber reinforced tubes. The force-displacement and contact force-time graphs were attained in consequence of low-velocity impact tests. The damage areas, their size and characteristics were scrutinized both visually and with the aid of a Microscope. The test results showed that when ambiance temperatures decreased, the damage areas considerably increased both filled with BNNP and without BNNP filament wound carbon fiber reinforced tubes.