Yifan Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yifan Zhang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Daixiu Wei
Tohoku University - Institute for Materials Research
3 shared publications - Hailong Yi
State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110819, China
3 shared publications - Renyi Xie
State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110819, China
3 shared publications - Hidemi Kato
Institute for Materials Research, Tohoku University, Sendai 980-8577, Japan
1 shared publication - Liqiang Wang
State Key Laboratory of Metal Matrix Composites, School of Material Science and Engineering, Shanghai Jiao Tong University, Shanghai, China
1 shared publication - Mengyuan Bi
State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110819, China
1 shared publication
Latest Publications
- Open Access
Tuning Microstructure and Mechanical Performance of a Co-Rich Transformation-Induced Plasticity High Entropy Alloy
Multi-principal element alloys and high-entropy alloys (HEAs) are emerging metallic materials with unprecedented structures and properties for various applications. In this study, we tuned the microstructure and mechanical performance of a recently designed high-performance Co-rich TRIP-HEA via thermomechanical processing (TMP). The microstructures of the HEA after various TMP routines were characterized, and their correlation with room-temperature tensile performance was clarified. The results showed that grain refinement is an effective strategy for enhancing strength while retaining satisfactory ductility. The formation of incoherent precipitates slightly improves the strength but inevitably sacrifices the ductility, which needs to be considered for optimizing the TMPs. The room temperature tensile yield strength and ultimate tensile strength were increased from 254.6 to 641.3 MPa and from 702.5 to 968.4 MPa, respectively, but the tensile elongation retains a satisfactory value of 68.8%. We herein provide important insights into the regulation of the microstructure and mechanical properties of TRIP-HEAs.
Open AccessTuning Microstructure and Mechanical Performance of a Co-Rich Transformation-Induced Plasticity High Entropy Alloy
Multi-principal element alloys and high-entropy alloys (HEAs) are emerging metallic materials with unprecedented structures and properties for various applications. In this study, we tuned the microstructure and mechanical performance of a recently designed high-performance Co-rich TRIP-HEA via thermomechanical processing (TMP). The microstructures of the HEA after various TMP routines were characterized, and their correlation with room-temperature tensile performance was clarified. The results showed that grain refinement is an effective strategy for enhancing strength while retaining satisfactory ductility. The formation of incoherent precipitates slightly improves the strength but inevitably sacrifices the ductility, which needs to be considered for optimizing the TMPs. The room temperature tensile yield strength and ultimate tensile strength were increased from 254.6 to 641.3 MPa and from 702.5 to 968.4 MPa, respectively, but the tensile elongation retains a satisfactory value of 68.8%. We herein provide important insights into the regulation of the microstructure and mechanical properties of TRIP-HEAs.
- Open Access
High-Temperature Deformation Behaviors of the C-Doped and N-Doped High Entropy Alloys
High entropy alloys (HEAs) containing multi-principal metallic constituents have attracted much attention. A good understanding of their hot-deformation behavior and recrystallization mechanism is the prerequisite for microstructures tuning and for optimizing mechanical performance. Here, the flow behavior and recrystallization mechanism of the N-doped and C-doped face-centered cubic phase HEAs are produced at high temperatures by hot-compression at 1123–1273 K, with strain rates of 0.1–0.001 s−1. Constitutive equations were successfully constructed to reveal flow behavior, and stress-strain curves were predicted using strain compensated polynomial functions. Discontinuous and continuous dynamic recrystallization proceeded concurrently when compressed at a low temperature and high strain rate, whereas discontinuous recrystallization, which occurs at primary grain boundaries, became predominant at a high temperature and low strain rate, significantly contributing to the refinement and homogenization of the grains. For this reason, a relatively high temperature and a low strain rate, in which the recrystallized grains exhibit equiaxed morphology and very weak texture, are more suitable for refining grains. The average size of the grains was approximately 10 μm. This study sheds light on grain optimization and mechanical properties through thermomechanical processing.
Open AccessHigh-Temperature Deformation Behaviors of the C-Doped and N-Doped High Entropy Alloys
High entropy alloys (HEAs) containing multi-principal metallic constituents have attracted much attention. A good understanding of their hot-deformation behavior and recrystallization mechanism is the prerequisite for microstructures tuning and for optimizing mechanical performance. Here, the flow behavior and recrystallization mechanism of the N-doped and C-doped face-centered cubic phase HEAs are produced at high temperatures by hot-compression at 1123–1273 K, with strain rates of 0.1–0.001 s−1. Constitutive equations were successfully constructed to reveal flow behavior, and stress-strain curves were predicted using strain compensated polynomial functions. Discontinuous and continuous dynamic recrystallization proceeded concurrently when compressed at a low temperature and high strain rate, whereas discontinuous recrystallization, which occurs at primary grain boundaries, became predominant at a high temperature and low strain rate, significantly contributing to the refinement and homogenization of the grains. For this reason, a relatively high temperature and a low strain rate, in which the recrystallized grains exhibit equiaxed morphology and very weak texture, are more suitable for refining grains. The average size of the grains was approximately 10 μm. This study sheds light on grain optimization and mechanical properties through thermomechanical processing.
- Open Access
Microstructure Refinement of a Transformation-Induced Plasticity High-Entropy Alloy
High-entropy alloys (HEAs) have attracted extensive interest due to their unprecedented structure and mechanical performance. We recently proposed a series of novel corich twinning induced plasticity (TWIP) and transformation induced plasticity (TRIP) HEAs with superior tensile properties at room temperature; however, the hot deformation behavior has not been reported. Here, we investigated the dynamic recrystallization behavior and grain refinement of a representative TRIP-HEA, compressed at temperatures of 1123–1273 K with strain rates of 0.1–0.001 s−1. We characterized the impact of the temperature and strain rate on the grain structure evolution. A constitutive equation was constructed to reveal the correlations between the flow stress, strain rate, temperature, and strain. The apparent activation energy was estimated to be ~385.7 kJ/mol. The discontinuous dynamic recrystallization played an important role in the grain refinement, particularly at a relatively higher temperature and a lower strain rate, and the volume fraction and morphology of the recrystallized grains exhibited a strong dependency on the Zener–Hollomon parameter. The study provides guidelines for the grain refinement of HEAs through thermomechanical processing.
Open AccessMicrostructure Refinement of a Transformation-Induced Plasticity High-Entropy Alloy
High-entropy alloys (HEAs) have attracted extensive interest due to their unprecedented structure and mechanical performance. We recently proposed a series of novel corich twinning induced plasticity (TWIP) and transformation induced plasticity (TRIP) HEAs with superior tensile properties at room temperature; however, the hot deformation behavior has not been reported. Here, we investigated the dynamic recrystallization behavior and grain refinement of a representative TRIP-HEA, compressed at temperatures of 1123–1273 K with strain rates of 0.1–0.001 s−1. We characterized the impact of the temperature and strain rate on the grain structure evolution. A constitutive equation was constructed to reveal the correlations between the flow stress, strain rate, temperature, and strain. The apparent activation energy was estimated to be ~385.7 kJ/mol. The discontinuous dynamic recrystallization played an important role in the grain refinement, particularly at a relatively higher temperature and a lower strain rate, and the volume fraction and morphology of the recrystallized grains exhibited a strong dependency on the Zener–Hollomon parameter. The study provides guidelines for the grain refinement of HEAs through thermomechanical processing.