Adi Subardi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Adi Subardi has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Ratna Kartikasari
Institut Teknologi Nasional Yogyakarta, Yogyakarta, Indonesia
4 shared publications - Yen-Pei Fu
Department of Materials Science and Engineering National Dong Hwa University Shou‐Feng Hualien Taiwan
4 shared publications - Andy Erwin Wijaya
Institut Teknologi Nasional Yogyakarta
3 shared publications - Iwan Susanto
Politeknik Negeri Jakarta
3 shared publications - Ade Indra
Faculty of Engineering, Department of Mechanical Engineering, Institut Teknologi Padang, Kp Olo, 25143, Padang, Sumatera Barat, Indonesia
2 shared publications - Belyamin Belyamin
Politeknik Negeri Jakarta
2 shared publications
Latest Publications
- Open Access
- 27 December 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (12 (126)) , 6-15
Development of Fe-13.8Cr-8.9Mn alloy for steel biomaterials
Traumatic, osteoarthritic, tumoral, and congenital bone issues impact human lives and health. The next generation of bone implants is made from biodegradable materials, including Fe-based materials with superior mechanical properties and high biocompatibility. However, efforts to inhibit the risk of inflammation and bacterial infection due to the biological response and corrosion properties of metals are a significant challenge. This study aims to develop biomaterials based on Fe-Cr-Mn alloys to obtain superior physical and mechanical properties through plasma nitriding. Each sample was plasma-nitridated in a vacuum chamber at various temperatures of 250–450 °C for 3 hours at a pressure of 1.8 kPa. Several main tests were performed to investigate the effects of plasma nitriding, such as the chemical compositions of raw material, surface nitrogen contents, phase changes, thickness, hardness, and corrosion. Those parameters were then used to evaluate plasma nitriding's effectiveness, including observing the change in phenomena at each temperature treatment. The results indicated that forming the S phase on the surface of Fe-13.8Cr-8.9Mn alloy is a saturated solution of nitrogen in ɣ-Fe, where the nitrogen content on the surface increases with increasing nitriding temperature. The layer's surface hardness is uniform across its whole thickness, which reduces as the grade of raw material passes through the nitride layer. The highest hardness at a nitriding temperature of 450 °C reached 625.3 VHN. The findings showed that the corrosion rate decreased significantly, reaching the lowest value, 0.0018 mm/year, at a plasma nitriding temperature of 450 °C. Plasma nitriding could enhance the physical and mechanical properties of Fe-Cr-Mn alloy
- 27 December 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (12 (126)) , 6-15
Open AccessDevelopment of Fe-13.8Cr-8.9Mn alloy for steel biomaterials
Traumatic, osteoarthritic, tumoral, and congenital bone issues impact human lives and health. The next generation of bone implants is made from biodegradable materials, including Fe-based materials with superior mechanical properties and high biocompatibility. However, efforts to inhibit the risk of inflammation and bacterial infection due to the biological response and corrosion properties of metals are a significant challenge. This study aims to develop biomaterials based on Fe-Cr-Mn alloys to obtain superior physical and mechanical properties through plasma nitriding. Each sample was plasma-nitridated in a vacuum chamber at various temperatures of 250–450 °C for 3 hours at a pressure of 1.8 kPa. Several main tests were performed to investigate the effects of plasma nitriding, such as the chemical compositions of raw material, surface nitrogen contents, phase changes, thickness, hardness, and corrosion. Those parameters were then used to evaluate plasma nitriding's effectiveness, including observing the change in phenomena at each temperature treatment. The results indicated that forming the S phase on the surface of Fe-13.8Cr-8.9Mn alloy is a saturated solution of nitrogen in ɣ-Fe, where the nitrogen content on the surface increases with increasing nitriding temperature. The layer's surface hardness is uniform across its whole thickness, which reduces as the grade of raw material passes through the nitride layer. The highest hardness at a nitriding temperature of 450 °C reached 625.3 VHN. The findings showed that the corrosion rate decreased significantly, reaching the lowest value, 0.0018 mm/year, at a plasma nitriding temperature of 450 °C. Plasma nitriding could enhance the physical and mechanical properties of Fe-Cr-Mn alloy
- 17 April 2023
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 142, 105862
The practical process of manufacturing poly(methyl methacrylate)-based scaffolds having high porosity and high strength
- 17 April 2023
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 142, 105862
The practical process of manufacturing poly(methyl methacrylate)-based scaffolds having high porosity and high strength
- Open Access
- 30 December 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (12 (120)) , 40-45
Development of oxide composite materials for cathode element of IT-SOFCs
Investigating the properties of composite oxide for intermediate temperature solid oxide fuel cells (IT-SOFCs) has been done as a new cathode material. Using a solid-state reaction method, the metallic oxide material has been employed to create the composite model system. During the sintering process, a model system of Sm0.5Sr0.35Ba0.15FeO3-δ (SSBF15) was constructed. Thermal gravimetric analysis (TG) was played to utilize the oxygen content and weight loss of the model. In the meantime, the structure of the composite was characterized using X-ray diffraction (XRD), and the conductivity properties were tested by thermal conductivity. The structural design was made possible by the findings, which revealed that the composite model structure exhibited the crystalline structure with perovskite phase. Weight losses during the construction of the structure were reflected in the decomposition and evaporation of the composite's constituent parts. After the calcination process up to 950 °C, the model system's formation oxygen content was obtained of 2.94 in 800 °C. The electrical conductivity maximum obtained in 12.2 S·cm-1 at 430 °C. At low temperatures, the conductive behavior was affected by the metallic element, while at higher temperatures, it was influenced by the ionic structure. As a result, mixed ionic and electric conductors (MIEC) were extensively utilized in the process of generating the conductive properties. The SSBF15 composite has a good chance of being used as an alternative cathode material with a perovskite single phase for future IT-SOFCs applications based on the structure and conductivity results. Additional testing and observation are required to determine the resistance's value when incorporated into the electrolyte and its heat expansion properties
- 30 December 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (12 (120)) , 40-45
Open AccessDevelopment of oxide composite materials for cathode element of IT-SOFCs
Investigating the properties of composite oxide for intermediate temperature solid oxide fuel cells (IT-SOFCs) has been done as a new cathode material. Using a solid-state reaction method, the metallic oxide material has been employed to create the composite model system. During the sintering process, a model system of Sm0.5Sr0.35Ba0.15FeO3-δ (SSBF15) was constructed. Thermal gravimetric analysis (TG) was played to utilize the oxygen content and weight loss of the model. In the meantime, the structure of the composite was characterized using X-ray diffraction (XRD), and the conductivity properties were tested by thermal conductivity. The structural design was made possible by the findings, which revealed that the composite model structure exhibited the crystalline structure with perovskite phase. Weight losses during the construction of the structure were reflected in the decomposition and evaporation of the composite's constituent parts. After the calcination process up to 950 °C, the model system's formation oxygen content was obtained of 2.94 in 800 °C. The electrical conductivity maximum obtained in 12.2 S·cm-1 at 430 °C. At low temperatures, the conductive behavior was affected by the metallic element, while at higher temperatures, it was influenced by the ionic structure. As a result, mixed ionic and electric conductors (MIEC) were extensively utilized in the process of generating the conductive properties. The SSBF15 composite has a good chance of being used as an alternative cathode material with a perovskite single phase for future IT-SOFCs applications based on the structure and conductivity results. Additional testing and observation are required to determine the resistance's value when incorporated into the electrolyte and its heat expansion properties
- Open Access
- 13 December 2022
- Published by Institute of Research and Community Services Diponegoro University (LPPM UNDIP) in Jurnal Kimia Sains dan Aplikasi
- Vol. 25 (10) , 346-351
Effect of Infiltration Ce0.8Sm0.2O1.9 Against Double Perovskite Performance LaBa0.5Sr0.5Co2O5+δ as IT-SOFC Cathode
Modifying the sample surface by infiltration technique using Ce0.8Sm0.2O1.9 (SDC) electrolyte has been done to increase the catalytic activity of the LaBa0.5Sr0.5Co2O5+δ (LBSC) cathode. The cathode powder structure was evaluated using X-ray diffraction (XRD) at room temperature, and the LBSC cathode microstructure was analyzed using scanning electron microscopy (SEM). The electrical conductivity of the LBSC cathode was tested using the four-probe DC method. Symmetrical cells were tested using a potentiostat Voltalab PGZ 301 and a digital source meter Keithley 2420. LBSC powder was discovered to have a tetragonal structure (space group: P4/mmm) with lattice parameters of a = 3.86253 Å, c = 7.73438 Å, and V = 115.338 Å. From the SEM image, the LBSC cathode has homogeneous, dense, and highly porous grains. The electrical conductivity showed metallic behavior, gradually decreasing from 167 S.cm-1 at 300℃ to 105 S.cm-1 at 800℃. A significant increase in current density (io) of 275% occurred at 800℃ from 154.10 mA.cm−2 (pure LBSC) to 577.86 mA.cm−2 (LBSC+0.5M SDC). The activation energy value (Ea) of symmetrical cells was determined using electrochemical impedance spectroscopy (EIS), low-field (LF), and high-field (HF) techniques. The activation energy of the LBSC+0.5 M SDC specimen was 47.9 kJ mol-1 or 79.4% lower than the activation energy of the LBSC cathode specimen without infiltration at atmospheric pressure of 0.03 atm. These results indicate that SDC infiltration of the LBSC cathode can reduce the activation energy of the significant. The cathode membrane adheres quite well to the electrolyte membrane, the cathode porosity varies in the range of 1–4 µm, and the grain size is 0.1–1.5 µm.
- 13 December 2022
- Published by Institute of Research and Community Services Diponegoro University (LPPM UNDIP) in Jurnal Kimia Sains dan Aplikasi
- Vol. 25 (10) , 346-351
Open AccessEffect of Infiltration Ce0.8Sm0.2O1.9 Against Double Perovskite Performance LaBa0.5Sr0.5Co2O5+δ as IT-SOFC Cathode
Modifying the sample surface by infiltration technique using Ce0.8Sm0.2O1.9 (SDC) electrolyte has been done to increase the catalytic activity of the LaBa0.5Sr0.5Co2O5+δ (LBSC) cathode. The cathode powder structure was evaluated using X-ray diffraction (XRD) at room temperature, and the LBSC cathode microstructure was analyzed using scanning electron microscopy (SEM). The electrical conductivity of the LBSC cathode was tested using the four-probe DC method. Symmetrical cells were tested using a potentiostat Voltalab PGZ 301 and a digital source meter Keithley 2420. LBSC powder was discovered to have a tetragonal structure (space group: P4/mmm) with lattice parameters of a = 3.86253 Å, c = 7.73438 Å, and V = 115.338 Å. From the SEM image, the LBSC cathode has homogeneous, dense, and highly porous grains. The electrical conductivity showed metallic behavior, gradually decreasing from 167 S.cm-1 at 300℃ to 105 S.cm-1 at 800℃. A significant increase in current density (io) of 275% occurred at 800℃ from 154.10 mA.cm−2 (pure LBSC) to 577.86 mA.cm−2 (LBSC+0.5M SDC). The activation energy value (Ea) of symmetrical cells was determined using electrochemical impedance spectroscopy (EIS), low-field (LF), and high-field (HF) techniques. The activation energy of the LBSC+0.5 M SDC specimen was 47.9 kJ mol-1 or 79.4% lower than the activation energy of the LBSC cathode specimen without infiltration at atmospheric pressure of 0.03 atm. These results indicate that SDC infiltration of the LBSC cathode can reduce the activation energy of the significant. The cathode membrane adheres quite well to the electrolyte membrane, the cathode porosity varies in the range of 1–4 µm, and the grain size is 0.1–1.5 µm.
- Open Access
- 29 November 2022
- Published by Institute of Research and Community Services Diponegoro University (LPPM UNDIP) in Jurnal Kimia Sains dan Aplikasi
- Vol. 25 (9) , 322-328
Enhanced SOFC Cathode Performance Through Surface Modification of NdBa0.5Sr0.5Co2O5+δ Nanoparticles
The cathode materials fabrication with outstanding performance and stability at intermediate temperatures of 600–800℃ is required for the prospective mass production of solid oxide fuel cells (SOFCs). Infiltration is a potential method because it has proven successful in fabrication and cell performance enhancement. This study mainly focuses on the electrical conductivity and long-term reliability of cathode symmetric cells NdBa0.5Sr0.5Co2O5+δ (NBSC) fabricated by traditional solid-state reaction techniques. The electrical conductivity value of the cathode is in the range of 174–278 S.cm-1. Impedance analysis showed that the infiltration of 0.5M SDC on the NBSC cathode surface dramatically reduced the polarization resistance (Rp) between layers (cathode-electrolyte) from 3.32 Ω.cm2 to 1.82 Ω.cm2 at 600℃ or decreased by 45 % compared to NBSC cathode without 0.5M SDC infiltration. The enhanced stability of NBSC cathode specimens with 0.5M SDC infiltration (NBSC+0.5 M SDC) under SOFC operating conditions proves that samples with infiltration extend their lifetime. Compared to the NBSC cathode, the NBSC+0.5 M SDC cathode has better long-term stability with a lower RP value of 2.35 Ω.cm2. In the OPP range of 0.214-0.0027 atm at 800℃, the relatively tiny Rp value of the symmetrical cell is between 0.030 Ω.cm2 and 0.039 Ω.cm2, below the 0.15 Ω.cm2 suitable performance limit for solid oxide fuel cells.
- 29 November 2022
- Published by Institute of Research and Community Services Diponegoro University (LPPM UNDIP) in Jurnal Kimia Sains dan Aplikasi
- Vol. 25 (9) , 322-328
Open AccessEnhanced SOFC Cathode Performance Through Surface Modification of NdBa0.5Sr0.5Co2O5+δ Nanoparticles
The cathode materials fabrication with outstanding performance and stability at intermediate temperatures of 600–800℃ is required for the prospective mass production of solid oxide fuel cells (SOFCs). Infiltration is a potential method because it has proven successful in fabrication and cell performance enhancement. This study mainly focuses on the electrical conductivity and long-term reliability of cathode symmetric cells NdBa0.5Sr0.5Co2O5+δ (NBSC) fabricated by traditional solid-state reaction techniques. The electrical conductivity value of the cathode is in the range of 174–278 S.cm-1. Impedance analysis showed that the infiltration of 0.5M SDC on the NBSC cathode surface dramatically reduced the polarization resistance (Rp) between layers (cathode-electrolyte) from 3.32 Ω.cm2 to 1.82 Ω.cm2 at 600℃ or decreased by 45 % compared to NBSC cathode without 0.5M SDC infiltration. The enhanced stability of NBSC cathode specimens with 0.5M SDC infiltration (NBSC+0.5 M SDC) under SOFC operating conditions proves that samples with infiltration extend their lifetime. Compared to the NBSC cathode, the NBSC+0.5 M SDC cathode has better long-term stability with a lower RP value of 2.35 Ω.cm2. In the OPP range of 0.214-0.0027 atm at 800℃, the relatively tiny Rp value of the symmetrical cell is between 0.030 Ω.cm2 and 0.039 Ω.cm2, below the 0.15 Ω.cm2 suitable performance limit for solid oxide fuel cells.
- Open Access
- 31 October 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (12(113)) , 60-68
Development of Fe-11Al-xMN alloy steel on cryogenic temperatures
This research is focused on increasing the reliability of Fe-11Al-Mn by combining the properties of Mn and the superiority of Fe-Al-C under cryogenic temperature. Three Fe-11Al-Mn alloys with compositions of 15 wt % Mn (F15), 20 wt % Mn (F20), and 25 wt % Mn (F25) were investigated. The cryogenic process uses liquid nitrogen in a temperature range of 0–196 °C. Hardness testing using the Vickers method and SEM was used to analyze the microstructure. X-ray diffraction (XRD) testing was conducted to ensure the Fe-11Al-Mn alloy phase and corrosion testing was carried out using the three-electrode cell polarization method. With the addition of Mn, the Vickers hardness of the Fe-11Al-Mn alloy decreased from 331.50 VHN at 15 wt % to 297.91 VHN at 25 wt %. The value of tensile strength and fracture elongation values were 742.21 MPa, 35.3 % EI; 789.03 MPa, 41.2 % EI; and 894.42 MPa, 50.2 % EI, for F15, F20, and F25, respectively. An important factor for improving the performance of cryogenic materials is the impact mechanism. The resulting impact toughness increased by 2.85 J/mm2 to 3.30 J/mm2 for F.15 and F25, respectively. The addition of the element Mn increases the corrosion resistance of the Fe-11Al-Mn alloy. The lowest corrosion rate occurs at 25 % wt Mn to 0.016 mm/year. Based on the results, the F25 alloy has the highest mechanical and corrosion resistance of the three types of alloys equivalent to SS 304 stainless steel. The microstructure of Fe-11Al-Mn alloy was similar between before and after cryogenic temperature treatment, this condition showed that the microstructure did not change during the process. From the overall results, the Fa-11Al-Mn alloy is a promising candidate for material applications working at cryogenic temperatures by optimizing the Mn content
- 31 October 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (12(113)) , 60-68
Open AccessDevelopment of Fe-11Al-xMN alloy steel on cryogenic temperatures
This research is focused on increasing the reliability of Fe-11Al-Mn by combining the properties of Mn and the superiority of Fe-Al-C under cryogenic temperature. Three Fe-11Al-Mn alloys with compositions of 15 wt % Mn (F15), 20 wt % Mn (F20), and 25 wt % Mn (F25) were investigated. The cryogenic process uses liquid nitrogen in a temperature range of 0–196 °C. Hardness testing using the Vickers method and SEM was used to analyze the microstructure. X-ray diffraction (XRD) testing was conducted to ensure the Fe-11Al-Mn alloy phase and corrosion testing was carried out using the three-electrode cell polarization method. With the addition of Mn, the Vickers hardness of the Fe-11Al-Mn alloy decreased from 331.50 VHN at 15 wt % to 297.91 VHN at 25 wt %. The value of tensile strength and fracture elongation values were 742.21 MPa, 35.3 % EI; 789.03 MPa, 41.2 % EI; and 894.42 MPa, 50.2 % EI, for F15, F20, and F25, respectively. An important factor for improving the performance of cryogenic materials is the impact mechanism. The resulting impact toughness increased by 2.85 J/mm2 to 3.30 J/mm2 for F.15 and F25, respectively. The addition of the element Mn increases the corrosion resistance of the Fe-11Al-Mn alloy. The lowest corrosion rate occurs at 25 % wt Mn to 0.016 mm/year. Based on the results, the F25 alloy has the highest mechanical and corrosion resistance of the three types of alloys equivalent to SS 304 stainless steel. The microstructure of Fe-11Al-Mn alloy was similar between before and after cryogenic temperature treatment, this condition showed that the microstructure did not change during the process. From the overall results, the Fa-11Al-Mn alloy is a promising candidate for material applications working at cryogenic temperatures by optimizing the Mn content
- Open Access
- 31 August 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (5(112)) , 6-11
Design of solid oxide structure on the composite cathode for IT-SOFC
Solid oxide structure of the cobalt-free composite has been exploited as a new cathode material for IT-SOFCs. The composite model system was synthesized using the metallic oxide material, which was formed by a solid-state reaction technique. The generation of the Sm0.5Sr0.25Ba0.25FeO3-δ (SSBF) model system was carried out during the sintering process. The weight loss and oxygen content were investigated by thermal gravimetric analysis (TG). Meanwhile, X-ray diffraction characterized the structure of the composite and thermal conductivity tested the conductivity properties. The results showed that the structure of the SSBF composite demonstrated the perovskite single phase leading to the structural design. The decomposition and evaporation of the constituent elements of the composite corresponded to weight losses during the constructing process. The oxygen content of the model system was 2.98 after the calcination process. The electrical conductivity value reached 2 S cm-1 at 400 °C and increases to a maximum of 7.5 S cm-1 at 710 °C. The metallic element played to generating the conductive behavior at the low temperature, while the ionic structure acted as elevated temperature. So, mixed ionic and electric conductors (MIEC) were employed comprehensively for creating the conductive properties. Based on the structure and conductivity results, the SSBF composite has a good chance as an alternative cathode material with a perovskite single phase for future TI-SOFCs applications
- 31 August 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (5(112)) , 6-11
Open AccessDesign of solid oxide structure on the composite cathode for IT-SOFC
Solid oxide structure of the cobalt-free composite has been exploited as a new cathode material for IT-SOFCs. The composite model system was synthesized using the metallic oxide material, which was formed by a solid-state reaction technique. The generation of the Sm0.5Sr0.25Ba0.25FeO3-δ (SSBF) model system was carried out during the sintering process. The weight loss and oxygen content were investigated by thermal gravimetric analysis (TG). Meanwhile, X-ray diffraction characterized the structure of the composite and thermal conductivity tested the conductivity properties. The results showed that the structure of the SSBF composite demonstrated the perovskite single phase leading to the structural design. The decomposition and evaporation of the constituent elements of the composite corresponded to weight losses during the constructing process. The oxygen content of the model system was 2.98 after the calcination process. The electrical conductivity value reached 2 S cm-1 at 400 °C and increases to a maximum of 7.5 S cm-1 at 710 °C. The metallic element played to generating the conductive behavior at the low temperature, while the ionic structure acted as elevated temperature. So, mixed ionic and electric conductors (MIEC) were employed comprehensively for creating the conductive properties. Based on the structure and conductivity results, the SSBF composite has a good chance as an alternative cathode material with a perovskite single phase for future TI-SOFCs applications
- Open Access
- 30 April 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (12 (110)) , 6-14
An analysis of SmBa0.5Sr0.5Co2O5+δ double perovskite oxide for intermediate–temperature solid oxide fuel cells
The main obstacle to solid oxide fuel cells (SOFCs) implementation is the high operating temperature in the range of 800–1,000 °C so that it has an impact on high costs. SOFCs work at high temperatures causing rapid breakdown between layers (anode, electrolyte, and cathode) because they have different thermal expansion. The study focused on reducing the operating temperature in the medium temperature range. SmBa0.5Sr0.5Co2O5+δ (SBSC) oxide was studied as a cathode material for IT-SOFCs based on Ce0.8Sm0.2O1.9 (SDC) electrolyte. The SBSC powder was prepared using the solid-state reaction method with repeated ball-milling and calcining. Alumina grinding balls are used because they have a high hardness to crush and smooth the powder of SOFC material. The specimens were then tested as cathode material for SOFC at intermediate temperature (600–800 °C) using X-ray powder diffraction (XRD), thermogravimetric analysis (TGA), electrochemical, and scanning electron microscopy (SEM) tests. The X-ray powder diffraction (XRD) pattern of SBSC powder can be indexed to a tetragonal space group (P4/mmm). The overall change in mass of the SBSC powder is 8 % at a temperature range of 125–800 °C. A sample of SBSC powder showed a high oxygen content (5+δ) that reached 5.92 and 5.41 at temperatures of 200 °C and 800 °C, respectively. High diffusion levels and increased surface activity of oxygen reduction reactions (ORRs) can be affected by high oxygen content (5+δ). The polarization resistance (Rp) of samples sintered at 1000 °C is 4.02 Ωcm2 at 600 °C, 1.04 Ωcm2 at 700 °C, and 0.42 Ωcm2 at 800 °C. The power density of the SBSC cathode is 336.1, 387.3, and 357.4 mW/cm2 at temperatures of 625 °C, 650 °C, and 675 °C, respectively. The SBSC demonstrates as a prospective cathode material for IT-SOFC
- 30 April 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (12 (110)) , 6-14
Open AccessAn analysis of SmBa0.5Sr0.5Co2O5+δ double perovskite oxide for intermediate–temperature solid oxide fuel cells
The main obstacle to solid oxide fuel cells (SOFCs) implementation is the high operating temperature in the range of 800–1,000 °C so that it has an impact on high costs. SOFCs work at high temperatures causing rapid breakdown between layers (anode, electrolyte, and cathode) because they have different thermal expansion. The study focused on reducing the operating temperature in the medium temperature range. SmBa0.5Sr0.5Co2O5+δ (SBSC) oxide was studied as a cathode material for IT-SOFCs based on Ce0.8Sm0.2O1.9 (SDC) electrolyte. The SBSC powder was prepared using the solid-state reaction method with repeated ball-milling and calcining. Alumina grinding balls are used because they have a high hardness to crush and smooth the powder of SOFC material. The specimens were then tested as cathode material for SOFC at intermediate temperature (600–800 °C) using X-ray powder diffraction (XRD), thermogravimetric analysis (TGA), electrochemical, and scanning electron microscopy (SEM) tests. The X-ray powder diffraction (XRD) pattern of SBSC powder can be indexed to a tetragonal space group (P4/mmm). The overall change in mass of the SBSC powder is 8 % at a temperature range of 125–800 °C. A sample of SBSC powder showed a high oxygen content (5+δ) that reached 5.92 and 5.41 at temperatures of 200 °C and 800 °C, respectively. High diffusion levels and increased surface activity of oxygen reduction reactions (ORRs) can be affected by high oxygen content (5+δ). The polarization resistance (Rp) of samples sintered at 1000 °C is 4.02 Ωcm2 at 600 °C, 1.04 Ωcm2 at 700 °C, and 0.42 Ωcm2 at 800 °C. The power density of the SBSC cathode is 336.1, 387.3, and 357.4 mW/cm2 at temperatures of 625 °C, 650 °C, and 675 °C, respectively. The SBSC demonstrates as a prospective cathode material for IT-SOFC
- Open Access
- 26 February 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (12 (109)) , 29-35
Development of Fe-5Al-1C alloys for grinding ball
Our object of research is to combine the properties of Mn and the advantages of Fe-Al-C to improve the performance of grinding ball materials. Three Fe-5Al-1C alloys with compositions of 15 wt% Mn (FAM15), 20 wt% Mn (FAM20), and 25 wt% Mn (FAM25) were investigated. Argon gas was used to assist the removal of dissolved oxygen and to control the formation of metal oxides during Fe-Al-Mn-C (FAMC) fabrication. Microstructure analysis was conducted using scanning electron microscopy, and the Vickers microhardness tester was used to evaluate hardness. To guarantee the Fe-5Al-1C-Mn alloy phase, X-ray diffraction (XRD) test was performed. The EDS test was carried out to show the composition at different points and to observe the presence of several phases in the FAMC alloy system. A pin-on-disc method was employed for a dry sliding wear test, and corrosion testing was performed using the three-electrode cell polarization method. With the addition of Mn, the Vickers hardness of the FAMC alloy raised from 194.4 VHN at 15 wt% to 265 VHN at 25 wt%. The tensile strength and fracture elongation values were 424.69 MPa, 27.16 % EI; 434.72 MPa, 33.6 % EI; and 485.71 MPa, 38.48 % EI for FAM15, FAM20, and FAM25, respectively. A crucial factor for increasing the performance of grinding ball is the wear mechanism. The wear rate results for FAM25 show a decline of more than 57 % compared to FAM15 due to an increase in the hard intermetallic area. The addition of Mn elements increased the corrosion resistance of the FAMC alloys; the lowest corrosion rate occurred at 25 wt% Mn content at up to 0.036 mm/yr. According to the experimental results, the FAM25 alloys have the highest mechanical and corrosion resistance of the three types of alloys. The FAMC alloy is a promising candidate for application as a material for grinding balls by optimizing the Mn content
- 26 February 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (12 (109)) , 29-35
Open AccessDevelopment of Fe-5Al-1C alloys for grinding ball
Our object of research is to combine the properties of Mn and the advantages of Fe-Al-C to improve the performance of grinding ball materials. Three Fe-5Al-1C alloys with compositions of 15 wt% Mn (FAM15), 20 wt% Mn (FAM20), and 25 wt% Mn (FAM25) were investigated. Argon gas was used to assist the removal of dissolved oxygen and to control the formation of metal oxides during Fe-Al-Mn-C (FAMC) fabrication. Microstructure analysis was conducted using scanning electron microscopy, and the Vickers microhardness tester was used to evaluate hardness. To guarantee the Fe-5Al-1C-Mn alloy phase, X-ray diffraction (XRD) test was performed. The EDS test was carried out to show the composition at different points and to observe the presence of several phases in the FAMC alloy system. A pin-on-disc method was employed for a dry sliding wear test, and corrosion testing was performed using the three-electrode cell polarization method. With the addition of Mn, the Vickers hardness of the FAMC alloy raised from 194.4 VHN at 15 wt% to 265 VHN at 25 wt%. The tensile strength and fracture elongation values were 424.69 MPa, 27.16 % EI; 434.72 MPa, 33.6 % EI; and 485.71 MPa, 38.48 % EI for FAM15, FAM20, and FAM25, respectively. A crucial factor for increasing the performance of grinding ball is the wear mechanism. The wear rate results for FAM25 show a decline of more than 57 % compared to FAM15 due to an increase in the hard intermetallic area. The addition of Mn elements increased the corrosion resistance of the FAMC alloys; the lowest corrosion rate occurred at 25 wt% Mn content at up to 0.036 mm/yr. According to the experimental results, the FAM25 alloys have the highest mechanical and corrosion resistance of the three types of alloys. The FAMC alloy is a promising candidate for application as a material for grinding balls by optimizing the Mn content