Shuaicai Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Shuaicai Liu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Bowen Yang
College of Aviation Engineering, Civil Aviation Flight University of China, Guanghan 618307, China
1 shared publication - Guanbiao Zhang
Composite Center, COMAC, Shanghai, China
1 shared publication - Hongshuai Huang
College of Aviation Engineering, Civil Aviation Flight University of China, Guanghan 618307, China
1 shared publication - Jiying Zhang
Requirement Engineering Development, COMAC, Shanghai, China
1 shared publication - Limeng Zhang
Composite Center, COMAC, Shanghai, China
1 shared publication - Ran Zhang
The Second Research Institute of Civil Aviation Administration of China, Chengdu 610041, China
1 shared publication
Latest Publications
- Open Access
Design and Validation of a Dielectric Method-Based Composite Material Curing Monitoring Platform
Monitoring the curing process is crucial for guiding and optimizing the curing procedures of composite material repair patches. Traditional embedded online monitoring methods are limited in their ability to track the curing process of these patches. This paper presents a composite material curing monitoring platform designed using dielectric methods. It integrates temperature control, pressure control, dielectric signal acquisition, control and display modules, and is specifically tailored for bag molding curing of repair patches. The platform measures the ionic viscosity of T300 2019B composites, analyzes the curing index, and correlates it with DSC-cured degree tests. The results indicate that the multiple ionic viscosity curves obtained from monitoring exhibit consistent trends, with correlation coefficients between curves exceeding 0.96. The changes in curing index align with the changes in curing degree, demonstrating that the platform can reliably and accurately monitor the ionic viscosity of repair patches. This platform enables effective monitoring of the ionic viscosity during the curing process of composite material repair patches.
Open AccessDesign and Validation of a Dielectric Method-Based Composite Material Curing Monitoring Platform
Monitoring the curing process is crucial for guiding and optimizing the curing procedures of composite material repair patches. Traditional embedded online monitoring methods are limited in their ability to track the curing process of these patches. This paper presents a composite material curing monitoring platform designed using dielectric methods. It integrates temperature control, pressure control, dielectric signal acquisition, control and display modules, and is specifically tailored for bag molding curing of repair patches. The platform measures the ionic viscosity of T300 2019B composites, analyzes the curing index, and correlates it with DSC-cured degree tests. The results indicate that the multiple ionic viscosity curves obtained from monitoring exhibit consistent trends, with correlation coefficients between curves exceeding 0.96. The changes in curing index align with the changes in curing degree, demonstrating that the platform can reliably and accurately monitor the ionic viscosity of repair patches. This platform enables effective monitoring of the ionic viscosity during the curing process of composite material repair patches.
- Open Access
- 1 March 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1102 (1) , 012002
The Design of Static Test Scheme for Composite Aileron Structure of Large Aircraft
According to the load conditions and structural features of composite aileron structure of large aircraft, the design techniques of full-scale static test scheme of aileron is studied, which can be used to examine the static strength and verify the airworthiness compliance of aileron structure. The overall test scheme design was carried out from the aspects of test load, test support, damage introduction and measurement scheme, and created a set of test design processes that meet the requirements of airworthiness. Loads screening was carried out by using strain coverage principle, the aerodynamic loads were transformed into test load by coordinate transformation. The wing was used as the aileron test support section, and a ground support device can also be designed to carry out aileron bench test. The introduction mode of aileron structure damage was defined, including the type, location and size. A reasonable layout of strain and displacement sensors was given for test measurement. Test results showed that the static test scheme in this paper can be used for the airworthiness compliance verification of static strength of aileron structure.
- 1 March 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1102 (1) , 012002
Open AccessThe Design of Static Test Scheme for Composite Aileron Structure of Large Aircraft
According to the load conditions and structural features of composite aileron structure of large aircraft, the design techniques of full-scale static test scheme of aileron is studied, which can be used to examine the static strength and verify the airworthiness compliance of aileron structure. The overall test scheme design was carried out from the aspects of test load, test support, damage introduction and measurement scheme, and created a set of test design processes that meet the requirements of airworthiness. Loads screening was carried out by using strain coverage principle, the aerodynamic loads were transformed into test load by coordinate transformation. The wing was used as the aileron test support section, and a ground support device can also be designed to carry out aileron bench test. The introduction mode of aileron structure damage was defined, including the type, location and size. A reasonable layout of strain and displacement sensors was given for test measurement. Test results showed that the static test scheme in this paper can be used for the airworthiness compliance verification of static strength of aileron structure.