Yang Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Yang Liu has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Fanli Meng
College of Information Science and Engineering, Northeastern University, Shenyang, 110819, China; Hebei Key Laboratory of Micro-Nano Precision Optical Sensing and Measurement Technology, Qinhuangdao, 066004, China; National Frontiers Science Center for Industrial Intelligence and Systems Optimization, Northeastern University, Shenyang, 110819, China; Key Laboratory of Data Analytics and Optimization for Smart Industry (Northeastern University), Ministry of Education, China
5 shared publications - Zhenyu Yuan
Northeastern University
5 shared publications - Chaoyang Xing
Department of Microsystem Integration, Beijing Institute of Aerospace Control Devices, Beijing, China
1 shared publication Fanli Meng
1 shared publicationHaidong Yu
State Grid Shandong Electric Power Research Institute,Jinan,Shandong,China,250003
1 shared publication- Hanyang Ji
College of Information Science and Engineering, Northeastern University, Shenyang, China
1 shared publication
Latest Publications
- 19 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-8
Orthorhombic Phase MoO3 Nanobelts Gas Sensor for Ultrasensitive Detection of Triethylamine
In view of the poor sensitivity and upper detection limit of triethylamine gas sensors, high performance triethylamine sensor was prepared by adjusting the crystalline phase of MoO3. In this work, the orthorhombic phase MoO3 nanobelts were synthesized through hydrothermal method and used for the detection of triethylamine. The experimental outcomes indicate that the orthorhombic phase MoO3 gas sensor exhibits the peak responsiveness, which reaches 774.47 when the concentration of triethylamine is 100 ppm at 220°C accompanied by a theoretical detection threshold as minute as 10 ppb. The orthorhombic phase MoO3 sensor has superior selectivity for triethylamine stemming from the robust Lewis acid-base interplay with MoO3 and triethylamine and the C-N of triethylamine is easily broken. Finally, the sensing mechanism of orthorhombic phase MoO3 gas sensor is deeply analyzed. Since orthorhombic phase MoO3 possesses a narrow band gap and small size effect, and has a high adsorption energy for triethylamine, the gas sensor exhibits excellent performance. The strategic design of crystalline phase modulation serves as a pivotal approach to enhancing the properties of gas sensors.
- 19 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-8
Orthorhombic Phase MoO3 Nanobelts Gas Sensor for Ultrasensitive Detection of Triethylamine
In view of the poor sensitivity and upper detection limit of triethylamine gas sensors, high performance triethylamine sensor was prepared by adjusting the crystalline phase of MoO3. In this work, the orthorhombic phase MoO3 nanobelts were synthesized through hydrothermal method and used for the detection of triethylamine. The experimental outcomes indicate that the orthorhombic phase MoO3 gas sensor exhibits the peak responsiveness, which reaches 774.47 when the concentration of triethylamine is 100 ppm at 220°C accompanied by a theoretical detection threshold as minute as 10 ppb. The orthorhombic phase MoO3 sensor has superior selectivity for triethylamine stemming from the robust Lewis acid-base interplay with MoO3 and triethylamine and the C-N of triethylamine is easily broken. Finally, the sensing mechanism of orthorhombic phase MoO3 gas sensor is deeply analyzed. Since orthorhombic phase MoO3 possesses a narrow band gap and small size effect, and has a high adsorption energy for triethylamine, the gas sensor exhibits excellent performance. The strategic design of crystalline phase modulation serves as a pivotal approach to enhancing the properties of gas sensors.
- 18 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-9
Humidity-Counteraction Identification of VOCs Driven by Semiconductor Sensor Temperature Modulation Response Data
The accurate and robust identification of volatile organic compounds (VOCs) poses significant challenges within the existing identification models. In this study, a humidity-counteraction identification scheme based on semiconductor sensor is developed for accurate and robust VOCs identification. Specifically, cyclic temperature modulation (CTM) measurements are utilized to improve sensor selectivity. The sensor response data undergo data augmentation to expand sample size and augment feature representation. Utilizing augmented samples, an accurate and robust species classification model is developed by integrating 2-D convolutional neural network (2D CNN) and generalized learning vector quantization (GLVQ), mitigating interference from concentration variations and ambient humidity changes. To counteract the ambient humidity drift for concentration calibration, the scaling factor method is developed to contract the distribution variance of sample modules. Subsequently, gas concentration calibrations are conducted using the scaled modules, showcasing remarkable accuracy and generalization performance. This study effectively mitigates the influence of ambient humidity on VOCs identification, offering a strategic and theoretical framework for developing high-performance identification models, with the expectations to play essential roles in smart medical care, intelligent driving, and industrial Internet of Things (IoT).
- 18 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-9
Humidity-Counteraction Identification of VOCs Driven by Semiconductor Sensor Temperature Modulation Response Data
The accurate and robust identification of volatile organic compounds (VOCs) poses significant challenges within the existing identification models. In this study, a humidity-counteraction identification scheme based on semiconductor sensor is developed for accurate and robust VOCs identification. Specifically, cyclic temperature modulation (CTM) measurements are utilized to improve sensor selectivity. The sensor response data undergo data augmentation to expand sample size and augment feature representation. Utilizing augmented samples, an accurate and robust species classification model is developed by integrating 2-D convolutional neural network (2D CNN) and generalized learning vector quantization (GLVQ), mitigating interference from concentration variations and ambient humidity changes. To counteract the ambient humidity drift for concentration calibration, the scaling factor method is developed to contract the distribution variance of sample modules. Subsequently, gas concentration calibrations are conducted using the scaled modules, showcasing remarkable accuracy and generalization performance. This study effectively mitigates the influence of ambient humidity on VOCs identification, offering a strategic and theoretical framework for developing high-performance identification models, with the expectations to play essential roles in smart medical care, intelligent driving, and industrial Internet of Things (IoT).
- 21 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Improved Multi-Point Estimate Probabilistic Harmonic Power Flow Algorithm Based On Dynamic Harmonic Model
With the widespread application of distributed photovoltaic(PV) power electronic converters, its inherent intermittency and randomness caused high harmonic content and a broad range of harmonic frequencies covered of the distribution network. A data-driven probabilistic harmonic power flow(PHPF) calculation method is proposed to effectively evaluate the uncertain harmonic state of the system and fully explore the actual operating characteristics of distributed PV. Firstly, the dynamic harmonic coupling matrix model(DHCMM) of distributed PV is established to reveal the mutual coupling relationship between harmonic voltage and harmonic current in different periods based on the actually measured data. Secondly, a PHPF algorithm based on an improved multi-point estimation method(IMPEM) is proposed to accurately grasp the statistical characteristics of output random variables such as harmonic voltage. According to the analysis results, the IMPEM-PHPF method based on the dynamic harmonic model can effectively analyze the time-varying characteristics of distributed PV harmonic sources and the harmonics are evaluated accurately in the power system.
- 21 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Improved Multi-Point Estimate Probabilistic Harmonic Power Flow Algorithm Based On Dynamic Harmonic Model
With the widespread application of distributed photovoltaic(PV) power electronic converters, its inherent intermittency and randomness caused high harmonic content and a broad range of harmonic frequencies covered of the distribution network. A data-driven probabilistic harmonic power flow(PHPF) calculation method is proposed to effectively evaluate the uncertain harmonic state of the system and fully explore the actual operating characteristics of distributed PV. Firstly, the dynamic harmonic coupling matrix model(DHCMM) of distributed PV is established to reveal the mutual coupling relationship between harmonic voltage and harmonic current in different periods based on the actually measured data. Secondly, a PHPF algorithm based on an improved multi-point estimation method(IMPEM) is proposed to accurately grasp the statistical characteristics of output random variables such as harmonic voltage. According to the analysis results, the IMPEM-PHPF method based on the dynamic harmonic model can effectively analyze the time-varying characteristics of distributed PV harmonic sources and the harmonics are evaluated accurately in the power system.
- 15 September 2023
- Published by Elsevier in Journal of Power Sources
- Vol. 584, 233625
High pressure molding Li10SnP2S12 ceramic electrolyte with low-grain-boundary-resistance for all-solid-state batteries
- 15 September 2023
- Published by Elsevier in Journal of Power Sources
- Vol. 584, 233625
High pressure molding Li10SnP2S12 ceramic electrolyte with low-grain-boundary-resistance for all-solid-state batteries
- 28 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-9
MoO3/SnO2Nanocomposite-Based Gas Sensor for Rapid Detection of Ammonia
Ammonia is harmful to human health, however, the detection limit of the sensor based on traditional semiconductor gas sensors is high and the speed is slow. Constructing heterostructure is an effective method to improve the performance of sensors. In this article, 1-D MoO 3 nanorods and SnO 2 nanoparticles are successfully combined to obtain MoO 3 /SnO 2 nanocomposite. The 1-D structure can increase the speed of electron transport, while the nanoparticles on the surface increase the specific surface area, more importantly, the structure maximizes the interface area between the two materials which can transfer electronic more efficiently. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), energy dispersive spectrometer (EDS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET), and Barrett–Joyner–Halenda (BJH) are used to analyze the microstructure and elemental composition of MoO 3 /SnO 2 . The diameter of MoO 3 /SnO 2 nanocomposite is approximately 200 nm and the distribution is uniform. The response of MoO 3 /SnO 2 nanocomposite to 100-ppm NH 3 is 12.7 at 280 °C, and the response/recovery time is 13/2 s. The detection limit for NH 3 can reach 10 ppb (response 1.3), which enables rapid detection of NH 3 at low concentration. Electron transport requires more energy to overcome the contact barrier between pure SnO 2 nanoparticles, which can also lead to electron emission and noise increase. However, the sensitive electrons of MoO 3 /SnO 2 nanocomposite can transmit electrons along the 1-D rod-like structure of MoO 3 , which undoubtedly accelerates the efficiency of electron transmission. Moreover, n-n heterojunction formed between MoO 3 and SnO 2 to bend the SnO 2 band and show better sensitivity to NH 3 . Therefore, MoO 3 /SnO 2 nanocomposite shows a low detection limit and a rapid response/recovery speed. Nevertheless, the nanoparticles on the surface of MoO 3 /SnO 2 nanocomposite begin to agglomerate with the increase of SnO 2 content, which leads to the decrease of gas-sensitive response. The formation process of MoO 3 /SnO 2 composites is also discussed in this article. The excellent gas sensing results show that MoO 3 /SnO 2 composites are a promising gas sensing material.
- 28 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-9
MoO3/SnO2Nanocomposite-Based Gas Sensor for Rapid Detection of Ammonia
Ammonia is harmful to human health, however, the detection limit of the sensor based on traditional semiconductor gas sensors is high and the speed is slow. Constructing heterostructure is an effective method to improve the performance of sensors. In this article, 1-D MoO 3 nanorods and SnO 2 nanoparticles are successfully combined to obtain MoO 3 /SnO 2 nanocomposite. The 1-D structure can increase the speed of electron transport, while the nanoparticles on the surface increase the specific surface area, more importantly, the structure maximizes the interface area between the two materials which can transfer electronic more efficiently. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), energy dispersive spectrometer (EDS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET), and Barrett–Joyner–Halenda (BJH) are used to analyze the microstructure and elemental composition of MoO 3 /SnO 2 . The diameter of MoO 3 /SnO 2 nanocomposite is approximately 200 nm and the distribution is uniform. The response of MoO 3 /SnO 2 nanocomposite to 100-ppm NH 3 is 12.7 at 280 °C, and the response/recovery time is 13/2 s. The detection limit for NH 3 can reach 10 ppb (response 1.3), which enables rapid detection of NH 3 at low concentration. Electron transport requires more energy to overcome the contact barrier between pure SnO 2 nanoparticles, which can also lead to electron emission and noise increase. However, the sensitive electrons of MoO 3 /SnO 2 nanocomposite can transmit electrons along the 1-D rod-like structure of MoO 3 , which undoubtedly accelerates the efficiency of electron transmission. Moreover, n-n heterojunction formed between MoO 3 and SnO 2 to bend the SnO 2 band and show better sensitivity to NH 3 . Therefore, MoO 3 /SnO 2 nanocomposite shows a low detection limit and a rapid response/recovery speed. Nevertheless, the nanoparticles on the surface of MoO 3 /SnO 2 nanocomposite begin to agglomerate with the increase of SnO 2 content, which leads to the decrease of gas-sensitive response. The formation process of MoO 3 /SnO 2 composites is also discussed in this article. The excellent gas sensing results show that MoO 3 /SnO 2 composites are a promising gas sensing material.
- 15 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (17) , 18435-18442
Highly Sensitive and Selective NH3 Sensor Based on Au Nanoparticle Loaded MoO3 Nanorods
MoO 3 is favored by scholars for its satisfactory gas-sensitive performance, and has made outstanding achievements in the detection of NH 3 . In this paper, MoO 3 nanorods are loaded with Au to obtain Au@MoO 3 , in order to further improve the gas sensitivity. By means of scanning electron microscopy (SEM), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), energy dispersive spectrometer (EDS) and X-ray photoelectron spectra (XPS), it is confirmed that Au nanoparticles are successfully modified on MoO 3 nanorods. The Au nanoparticles with the diameter of about 20-40 nm are uniformly dispersed on the surface of the nanorods with the diameter of about 100-200 nm. Gas sensitivity test results show that Au@MoO 3 has excellent sensitivity to NH 3 , and strong anti-interference to other gases, with outstanding selectivity. The response of Au@MoO 3 to 100 ppm NH 3 at the optimum operating temperature of 370 °C is as high as 882.5, moreover, it can detect NH 3 as low as 1 ppm (response 8.6). Compared with pure MoO 3 nanorods, the sensitivity is improved and the operating temperature is reduced. The sensitive mechanism of Au@MoO 3 is also discussed.
- 15 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (17) , 18435-18442
Highly Sensitive and Selective NH3 Sensor Based on Au Nanoparticle Loaded MoO3 Nanorods
MoO 3 is favored by scholars for its satisfactory gas-sensitive performance, and has made outstanding achievements in the detection of NH 3 . In this paper, MoO 3 nanorods are loaded with Au to obtain Au@MoO 3 , in order to further improve the gas sensitivity. By means of scanning electron microscopy (SEM), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), energy dispersive spectrometer (EDS) and X-ray photoelectron spectra (XPS), it is confirmed that Au nanoparticles are successfully modified on MoO 3 nanorods. The Au nanoparticles with the diameter of about 20-40 nm are uniformly dispersed on the surface of the nanorods with the diameter of about 100-200 nm. Gas sensitivity test results show that Au@MoO 3 has excellent sensitivity to NH 3 , and strong anti-interference to other gases, with outstanding selectivity. The response of Au@MoO 3 to 100 ppm NH 3 at the optimum operating temperature of 370 °C is as high as 882.5, moreover, it can detect NH 3 as low as 1 ppm (response 8.6). Compared with pure MoO 3 nanorods, the sensitivity is improved and the operating temperature is reduced. The sensitive mechanism of Au@MoO 3 is also discussed.
- 19 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-9
Rose-Like MoO₃/MoS₂/rGO Low-Temperature Ammonia Sensors Based on Multigas Detection Methods
In order to improve the sensitivity of the pure MoO 3 sensor to ammonia and reduce its operating temperature, MoO 3 /MoS 2 /rGO was prepared in this work, and the gas-sensitive performance of MoO 3 /MoS 2 /rGO was studied. The results of the static gas sensitivity test show that, compared with pure MoO 3 , MoO 3 /MoS 2 /rGO greatly improves the response of the sensor to ammonia at low temperature. Moreover, this article discusses the multigas detection methods by waveform-matched dynamic temperature modulation based on low-temperature gas sensor composites of rose-like MoO 3 /MoS 2 /rGO, which is used to solve the shortcoming of poor selectivity of metal-oxide-semiconductor gas sensor. Multigas (including acetone, methanol, ethanol, benzene, toluene, and ammonia) detection methods by waveform-matched dynamic temperature modulation are investigated, in which the experimental results show that the dynamic response curves of the sensor have obvious differences to each gas under different temperature waveform modulations. Temperature modulation waveforms with different periods and variations are investigated, including rectangular wave, triangular wave, and sine wave. This provides a feasible way to improve the selectivity of the sensor. In order to establish and verify the accuracy of the multigas detection model, 100 sets of response curves are selected for each waveform. Finally, the gas-sensing mechanism of gas-sensitive materials to ammonia is analyzed. Preparation of highly sensitive materials, dynamic testing, and gas identification methods can provide the technical basis for the application of gas sensors.
- 19 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-9
Rose-Like MoO₃/MoS₂/rGO Low-Temperature Ammonia Sensors Based on Multigas Detection Methods
In order to improve the sensitivity of the pure MoO 3 sensor to ammonia and reduce its operating temperature, MoO 3 /MoS 2 /rGO was prepared in this work, and the gas-sensitive performance of MoO 3 /MoS 2 /rGO was studied. The results of the static gas sensitivity test show that, compared with pure MoO 3 , MoO 3 /MoS 2 /rGO greatly improves the response of the sensor to ammonia at low temperature. Moreover, this article discusses the multigas detection methods by waveform-matched dynamic temperature modulation based on low-temperature gas sensor composites of rose-like MoO 3 /MoS 2 /rGO, which is used to solve the shortcoming of poor selectivity of metal-oxide-semiconductor gas sensor. Multigas (including acetone, methanol, ethanol, benzene, toluene, and ammonia) detection methods by waveform-matched dynamic temperature modulation are investigated, in which the experimental results show that the dynamic response curves of the sensor have obvious differences to each gas under different temperature waveform modulations. Temperature modulation waveforms with different periods and variations are investigated, including rectangular wave, triangular wave, and sine wave. This provides a feasible way to improve the selectivity of the sensor. In order to establish and verify the accuracy of the multigas detection model, 100 sets of response curves are selected for each waveform. Finally, the gas-sensing mechanism of gas-sensitive materials to ammonia is analyzed. Preparation of highly sensitive materials, dynamic testing, and gas identification methods can provide the technical basis for the application of gas sensors.