Jayaprakash Narayan Murugan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jayaprakash Narayan Murugan has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- P. Vinoth Kumar
School of Mechanical Engineering, Vellore Institute of Technology, Tamil Nadu, India
2 shared publications - Raghuraman N. Govardhan
Indian Institute of Science
2 shared publications - Sourabh Bhardwaj
KTH Royal Institute of Technology
2 shared publications - Sriram Rengarajan
Department of Aerospace Engineering, Indian Institute of Technology-Madras, Chennai 600036, India
2 shared publications - K. Ramachandra
Department of Aerospace Engineering, Indian Institute of Technology Madras, Chennai, India
1 shared publication - Kiran Chutkey
Indian Institute of Science, Bangalore 560012, India
1 shared publication
Latest Publications
- 10 October 2024
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics C
- Vol. 36 (05)
Reduction of the separation bubble size using the pressure feedback channel in supersonic flow across a forward-facing step
In high-speed flow applications, increased aero-thermodynamic loads, localized turbulent regions, instability, excessive drag and pressure losses are among the negative effects of the interaction between shock waves and boundary layers and the subsequent separation of the boundary layer. These drawbacks emphasize how crucial it is to look into ways to control the boundary layer separation caused by shock waves. In order to determine whether using a pressure feedback technique to regulate boundary layer separation on a two-dimensional forward-facing step (FFS) is effective, a numerical study is conducted. The pressure feedback technique utilizes a channel to remove fluid from the separated area and reintroduce it into the mainstream flow, by leveraging the pressure contrast as the motivating factor. Ansys Fluent 2021 simulation software is used to conduct a numerical study investigating shock wave boundary layer interaction over a FFS at a supersonic Mach number of 2.5. The present study aims to explore the effectiveness of implementing a pressure feedback channel near the FFS as a strategy for controlling flow separation induced by the step. Turbulence effects are simulated using a k-omega model, and the study employs a finite-volume method with upwind flux difference splitting and second-order upwind flow discretization. The simulation results indicate the efficacy of the pressure feedback mechanism in reducing flow separation, thus enhancing its role in separation control. Integration of an 80[ ]mm channel results in a notable 42.85% decrease in separation bubble size, while the longer 90[ ]mm channel yields an even more substantial 52.38% reduction.
- 10 October 2024
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics C
- Vol. 36 (05)
Reduction of the separation bubble size using the pressure feedback channel in supersonic flow across a forward-facing step
In high-speed flow applications, increased aero-thermodynamic loads, localized turbulent regions, instability, excessive drag and pressure losses are among the negative effects of the interaction between shock waves and boundary layers and the subsequent separation of the boundary layer. These drawbacks emphasize how crucial it is to look into ways to control the boundary layer separation caused by shock waves. In order to determine whether using a pressure feedback technique to regulate boundary layer separation on a two-dimensional forward-facing step (FFS) is effective, a numerical study is conducted. The pressure feedback technique utilizes a channel to remove fluid from the separated area and reintroduce it into the mainstream flow, by leveraging the pressure contrast as the motivating factor. Ansys Fluent 2021 simulation software is used to conduct a numerical study investigating shock wave boundary layer interaction over a FFS at a supersonic Mach number of 2.5. The present study aims to explore the effectiveness of implementing a pressure feedback channel near the FFS as a strategy for controlling flow separation induced by the step. Turbulence effects are simulated using a k-omega model, and the study employs a finite-volume method with upwind flux difference splitting and second-order upwind flow discretization. The simulation results indicate the efficacy of the pressure feedback mechanism in reducing flow separation, thus enhancing its role in separation control. Integration of an 80[ ]mm channel results in a notable 42.85% decrease in separation bubble size, while the longer 90[ ]mm channel yields an even more substantial 52.38% reduction.
- 1 December 2023
- Published by Springer Nature in Shock Waves
- Vol. 33 (7-8) , 569-583
Study of unsteadiness due to 3-D shock–boundary layer interaction in flow over a square-faced protuberance
- 1 December 2023
- Published by Springer Nature in Shock Waves
- Vol. 33 (7-8) , 569-583
Study of unsteadiness due to 3-D shock–boundary layer interaction in flow over a square-faced protuberance
- 20 October 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Vol. 237 (16) , 3800-3808
A computational study of leading-edge wall cooling effect on shock wave–boundary layer interaction in forward-facing step
A computational study has been done to understand the effect of leading-edge wall cooling on shock wave–boundary layer interaction. Shock wave–boundary layer interaction is studied over a forward-facing step at supersonic Mach 2.5. The study was carried out using Ansys. The work aims to explore the implementation of wall cooling at the leading edge as a separation control strategy for supersonic forward-facing step-induced flow separation. We use a finite-volume method based on upwind flux difference splitting and second-order upwind flow discretization. The simulation results are validated with the available experimental data. Furthermore, using numerical simulations, we found that the separation bubble size was reduced by 18.36% when the walls were marginally cooled to 150 K, while the separation was reduced by 32.65% when the walls were strongly cooled to 100 K.
- 20 October 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Vol. 237 (16) , 3800-3808
A computational study of leading-edge wall cooling effect on shock wave–boundary layer interaction in forward-facing step
A computational study has been done to understand the effect of leading-edge wall cooling on shock wave–boundary layer interaction. Shock wave–boundary layer interaction is studied over a forward-facing step at supersonic Mach 2.5. The study was carried out using Ansys. The work aims to explore the implementation of wall cooling at the leading edge as a separation control strategy for supersonic forward-facing step-induced flow separation. We use a finite-volume method based on upwind flux difference splitting and second-order upwind flow discretization. The simulation results are validated with the available experimental data. Furthermore, using numerical simulations, we found that the separation bubble size was reduced by 18.36% when the walls were marginally cooled to 150 K, while the separation was reduced by 32.65% when the walls were strongly cooled to 100 K.
- Open Access
Study of Unsteadiness due to 3-D Shock-Boundary Layer Interaction in Flow over a Square-faced Protuberance
The dynamics of shock-induced unsteady separated flow past a three-dimensional square-faced protuberance is investigated through wind tunnel experiments. Time-resolved schlieren imaging and unsteady surface pressure measurements are the diagnostics employed. Dynamic Mode Decomposition (DMD) of schlieren snapshots, and analysis of spectrum and correlations in pressure data are used to characterize and resolve the flow physics. The mean shock foot in the centreline is found to exhibit a Strouhal number of around 0.01, which is also the order of magnitude of the Strouhal numbers reported in the literature for two-dimensional shock-boundary layer interactions. The wall pressure spectra, in general, shift towards lower frequencies as we move away from (spanwise) centreline with some variation in the nature of peaks. The cross-correlation analysis depicts the strong dependence of the mean shock oscillations to the plateau region, and disturbances are found to travel upstream from inside the separation bubble. Good coherence is observed between the spanwise mean shock foot locations till a strouhal number of about 0.015 indicating that the 3-D shock foot largely moves to-and-fro in a coherent fashion.
Open AccessStudy of Unsteadiness due to 3-D Shock-Boundary Layer Interaction in Flow over a Square-faced Protuberance
The dynamics of shock-induced unsteady separated flow past a three-dimensional square-faced protuberance is investigated through wind tunnel experiments. Time-resolved schlieren imaging and unsteady surface pressure measurements are the diagnostics employed. Dynamic Mode Decomposition (DMD) of schlieren snapshots, and analysis of spectrum and correlations in pressure data are used to characterize and resolve the flow physics. The mean shock foot in the centreline is found to exhibit a Strouhal number of around 0.01, which is also the order of magnitude of the Strouhal numbers reported in the literature for two-dimensional shock-boundary layer interactions. The wall pressure spectra, in general, shift towards lower frequencies as we move away from (spanwise) centreline with some variation in the nature of peaks. The cross-correlation analysis depicts the strong dependence of the mean shock oscillations to the plateau region, and disturbances are found to travel upstream from inside the separation bubble. Good coherence is observed between the spanwise mean shock foot locations till a strouhal number of about 0.015 indicating that the 3-D shock foot largely moves to-and-fro in a coherent fashion.
- 13 August 2021
- Published by ASME International in Journal of Fluids Engineering
- Vol. 144 (2)
Effect of Passive Flow Control Devices on Base Pressure for Mach Numbers Between 0.5 and 1.4
Experimental studies are carried out on an axisymmetric cylindrical base body for six freestream Mach numbers between 0.54 and 1.41. Unsteady pressure is measured on the base surface using high-frequency response Kulite pressure transducers. The effect of passive flow control devices on the mean base pressure and the unsteady characteristics of base pressure have been studied. A blunt base, a conventional cavity device, and three different ventilated cavity devices have been tested along with four different rounded base lip devices. A total of 20 different base geometric modifications are tested at 6 freestream Mach numbers resulting in 120 test cases. The cavity devices improve the base pressure as compared to the blunt base case, particularly for freestream Mach numbers more than 0.98. Among all the cases considered, a maximum increase of 8.6% in the base pressure coefficient is noticed for the normal ventilated cavity device as compared to the blunt base case for freestream Mach number of 1.22. The power spectral density of base pressure fluctuations revealed the dominant peaks on the base surface. The Strouhal number associated with the coherent structures developing in the shear layer varies between 0.2 and 0.27 for the six freestream Mach numbers considered. In the presence of cavity devices, dominant peaks are observed for Strouhal numbers between 1 and 5. The root-mean-square, skewness, kurtosis of the base pressure fluctuations for all the cases are presented. Maximum reduction in base pressure fluctuation is observed for the normal and inclined ventilated cavity device configuration test cases.
- 13 August 2021
- Published by ASME International in Journal of Fluids Engineering
- Vol. 144 (2)
Effect of Passive Flow Control Devices on Base Pressure for Mach Numbers Between 0.5 and 1.4
Experimental studies are carried out on an axisymmetric cylindrical base body for six freestream Mach numbers between 0.54 and 1.41. Unsteady pressure is measured on the base surface using high-frequency response Kulite pressure transducers. The effect of passive flow control devices on the mean base pressure and the unsteady characteristics of base pressure have been studied. A blunt base, a conventional cavity device, and three different ventilated cavity devices have been tested along with four different rounded base lip devices. A total of 20 different base geometric modifications are tested at 6 freestream Mach numbers resulting in 120 test cases. The cavity devices improve the base pressure as compared to the blunt base case, particularly for freestream Mach numbers more than 0.98. Among all the cases considered, a maximum increase of 8.6% in the base pressure coefficient is noticed for the normal ventilated cavity device as compared to the blunt base case for freestream Mach number of 1.22. The power spectral density of base pressure fluctuations revealed the dominant peaks on the base surface. The Strouhal number associated with the coherent structures developing in the shear layer varies between 0.2 and 0.27 for the six freestream Mach numbers considered. In the presence of cavity devices, dominant peaks are observed for Strouhal numbers between 1 and 5. The root-mean-square, skewness, kurtosis of the base pressure fluctuations for all the cases are presented. Maximum reduction in base pressure fluctuation is observed for the normal and inclined ventilated cavity device configuration test cases.
- 19 March 2021
- Published by Springer Nature
- p. 219-226
Observation of Low-Frequency Shock Oscillation Over a Forward-Facing Step
- 19 March 2021
- Published by Springer Nature
- p. 219-226
Observation of Low-Frequency Shock Oscillation Over a Forward-Facing Step
- 1 January 2020
- Published by Begell House Inc. Publishers in Journal of Flow Visualization and Image Processing
- Vol. 27 (2) , 185-197
STUDY OF SHOCK WAVE-BOUNDARY LAYER INTERACTION USING HIGH-SPEED SCHLIEREN IMAGING
We study shock-wave boundary layer interaction in Mach 2.5 flow over a forward-facing step. The step height used for the present study is equal to twice the incoming boundary layer thickness. The experimental results from schlieren visualization and wall pressure measurements are presented in the present work. High-speed schlieren images are acquired at 10,000 frames per second. Micro second exposure schlieren visualization images show the unsteady nature of separation shock. Schlieren images show that the separation shock foot moves approximately of the order of step height. Spectra of separation shock location obtained from schlieren images also show two orders of magnitude smaller than the characteristic frequency of the incoming boundary layer. Instantaneous schlieren images shows formation of a series of compression waves inside the boundary layer and these waves combines to form a separation shock wave outside the boundary layer followed by wall shear layer, reattachment shock and an expansion fan. Spectra of unsteady wall pressure data near separation shock location also show a dominant frequency of that is two orders of magnitude smaller than the characteristic frequency of the incoming boundary layer. The frequency result from high-speed schlieren and unsteady wall pressure data agrees and hence high speed schlieren can be used to study the unsteady behavior of separation shock provided the model is two-dimensional.
- 1 January 2020
- Published by Begell House Inc. Publishers in Journal of Flow Visualization and Image Processing
- Vol. 27 (2) , 185-197
STUDY OF SHOCK WAVE-BOUNDARY LAYER INTERACTION USING HIGH-SPEED SCHLIEREN IMAGING
We study shock-wave boundary layer interaction in Mach 2.5 flow over a forward-facing step. The step height used for the present study is equal to twice the incoming boundary layer thickness. The experimental results from schlieren visualization and wall pressure measurements are presented in the present work. High-speed schlieren images are acquired at 10,000 frames per second. Micro second exposure schlieren visualization images show the unsteady nature of separation shock. Schlieren images show that the separation shock foot moves approximately of the order of step height. Spectra of separation shock location obtained from schlieren images also show two orders of magnitude smaller than the characteristic frequency of the incoming boundary layer. Instantaneous schlieren images shows formation of a series of compression waves inside the boundary layer and these waves combines to form a separation shock wave outside the boundary layer followed by wall shear layer, reattachment shock and an expansion fan. Spectra of unsteady wall pressure data near separation shock location also show a dominant frequency of that is two orders of magnitude smaller than the characteristic frequency of the incoming boundary layer. The frequency result from high-speed schlieren and unsteady wall pressure data agrees and hence high speed schlieren can be used to study the unsteady behavior of separation shock provided the model is two-dimensional.