Dhanapaul Selvaraj Aniesrani Delfiya
Research Subjects
Research Interests
Dhanapaul Selvaraj Aniesrani Delfiya has a total of 80 co-authors. Here are the top co-authors by number of shared publications:
- Subramaniam Murali
Engineering Section, ICAR - Central Institute of FisheriesTechnology, Kochi, India
18 shared publications Manoj P. Samuel
KSCSTE‐Centre for Water Resource Development and Management Kozhikode India
9 shared publications- Kuruthukulam Chacko Neethu
Engineering Division, ICAR-Central Institute of Fisheries Technology, Cochin, India
7 shared publications - Palli V. Alfiya
Division of Crop Production and Post‐Harvest Technology ICAR ‐ Indian Institute of Spices Research Kozhikode India
7 shared publications - George Ninan
ICAR- Central Institute of Fisheries Technology, Willingdon Island, Kerala 682029, India
6 shared publications - Kulandaisamy Thangavel
Department of Food and Agricultural Process Engineering, Tamil Nadu Agricultural University, Coimbatore, India
6 shared publications
Latest Publications
- 16 September 2026
- Published by Taylor & Francis in Drying Technology
- Vol. 44 (15) , 2301-2323
Advances in hybrid solar–infrared drying for food processing: Comparative design, energy performance, and quality evaluation
1. Drying is one of the most widely applied unit operations in food and agricultural processing, enabling shelf-life extension through moisture removal and suppression of microbial, enzymatic, and ...
- 16 September 2026
- Published by Taylor & Francis in Drying Technology
- Vol. 44 (15) , 2301-2323
Advances in hybrid solar–infrared drying for food processing: Comparative design, energy performance, and quality evaluation
1. Drying is one of the most widely applied unit operations in food and agricultural processing, enabling shelf-life extension through moisture removal and suppression of microbial, enzymatic, and ...
- 26 July 2026
- Published by Wiley in Journal of Food Process Engineering
- Vol. 49 (8) , e70709
Effects of Infrared, Hot Air and Infrared‐Assisted Hot Air‐Drying on Drying Characteristics, Quality, and Energy Efficiency of Turmeric Slices
The market value of turmeric is influenced strongly by volatile compounds which indicate product quality. In this study, turmeric slices of 5 mm with bed thicknesses of 50 mm were dried using three techniques: infrared (IR‐D), hot air (HA‐D), and infrared‐assisted hot air‐drying (IR‐HA‐D) at temperatures of 50°, 60°, and 70°C. This study examined the effects of increased bed thickness on drying kinetics, energy requirements, CO 2 emissions, and quality attributes under settings that more closely resemble industrial‐scale drying operations, in contrast to earlier studies that used a 25 mm bed thickness. Among the evaluated drying methods, IR‐HA‐D at 70°C exhibited the highest process efficiency, whereas IR‐HA‐D at 60°C provided superior retention of quality attributes, including curcumin, oleoresin, starch, and color. Seven thin‐layer drying models using nonlinear regression analysis were evaluated, with the Page model showing the best fit across all experimental conditions. The IR‐HA‐D method provided the highest retention of curcumin, oleoresin, starch and color value at 60°C, compared to both IR‐D and HA‐D. Statistical analysis confirmed that both drying techniques and temperature significantly influenced the quality characteristics of the dried turmeric ( p < 0.01). Effective moisture diffusivity ranged from 7.61 × 10 −11 to 2.53 × 10 −10 m 2 s −1 while the activation energy required for moisture diffusion was 31.88 kJ mol −1 for IR‐D, 45.13 kJ mol −1 for HA‐D, and 32.11 kJ mol −1 for IR‐HA‐D.
- 26 July 2026
- Published by Wiley in Journal of Food Process Engineering
- Vol. 49 (8) , e70709
Effects of Infrared, Hot Air and Infrared‐Assisted Hot Air‐Drying on Drying Characteristics, Quality, and Energy Efficiency of Turmeric Slices
The market value of turmeric is influenced strongly by volatile compounds which indicate product quality. In this study, turmeric slices of 5 mm with bed thicknesses of 50 mm were dried using three techniques: infrared (IR‐D), hot air (HA‐D), and infrared‐assisted hot air‐drying (IR‐HA‐D) at temperatures of 50°, 60°, and 70°C. This study examined the effects of increased bed thickness on drying kinetics, energy requirements, CO 2 emissions, and quality attributes under settings that more closely resemble industrial‐scale drying operations, in contrast to earlier studies that used a 25 mm bed thickness. Among the evaluated drying methods, IR‐HA‐D at 70°C exhibited the highest process efficiency, whereas IR‐HA‐D at 60°C provided superior retention of quality attributes, including curcumin, oleoresin, starch, and color. Seven thin‐layer drying models using nonlinear regression analysis were evaluated, with the Page model showing the best fit across all experimental conditions. The IR‐HA‐D method provided the highest retention of curcumin, oleoresin, starch and color value at 60°C, compared to both IR‐D and HA‐D. Statistical analysis confirmed that both drying techniques and temperature significantly influenced the quality characteristics of the dried turmeric ( p < 0.01). Effective moisture diffusivity ranged from 7.61 × 10 −11 to 2.53 × 10 −10 m 2 s −1 while the activation energy required for moisture diffusion was 31.88 kJ mol −1 for IR‐D, 45.13 kJ mol −1 for HA‐D, and 32.11 kJ mol −1 for IR‐HA‐D.
- 8 April 2026
- Published by Wiley in Journal of Food Process Engineering
- Vol. 49 (4)
Integration of a Solar Air Heating System in a Continuous Infrared Dryer for Energy‐Efficient Drying
The hybrid infrared‐solar technology ensures energy‐efficient, sustainable, and low‐carbon drying, reduces the operational cost of the drying process, and improves the drying performance of the dryer. The solar flat plate collector provides the hot air supply for the infrared dryer, which measurably reduces the electrical energy demand of the infrared dryer. This study aimed to develop a solar‐assisted continuous infrared dryer that utilizes the hot air generated by the solar flat plate collector. The fish drying using this dryer was conducted at various operating conditions, such as Infrared alone (1500 and 3000 W/m 2 ) and solar‐assisted infrared (1500 and 3000 W/m 2 ). The energy consumption from the electrical source was found to be lower (1.55 kWh) in solar‐assisted infrared with 1500 W/m 2 , and the electrical energy of 61.63% was replaced by solar thermal energy supplied by the SFPC during fish drying. The maximum drying efficiency of 12.27% was observed in solar‐assisted infrared at 1500 W/m 2 , followed by 11.25% solar‐assisted infrared at 3000 W/m 2 . The payback period for fish drying using this dryer was found to be less than 0.64, and the benefit–cost ratio of more than 1.55, except for infrared drying without solar at 1500 W/m 2 . This study shows the successful and efficient combination of solar energy and an infrared energy source for food drying.
- 8 April 2026
- Published by Wiley in Journal of Food Process Engineering
- Vol. 49 (4)
Integration of a Solar Air Heating System in a Continuous Infrared Dryer for Energy‐Efficient Drying
The hybrid infrared‐solar technology ensures energy‐efficient, sustainable, and low‐carbon drying, reduces the operational cost of the drying process, and improves the drying performance of the dryer. The solar flat plate collector provides the hot air supply for the infrared dryer, which measurably reduces the electrical energy demand of the infrared dryer. This study aimed to develop a solar‐assisted continuous infrared dryer that utilizes the hot air generated by the solar flat plate collector. The fish drying using this dryer was conducted at various operating conditions, such as Infrared alone (1500 and 3000 W/m 2 ) and solar‐assisted infrared (1500 and 3000 W/m 2 ). The energy consumption from the electrical source was found to be lower (1.55 kWh) in solar‐assisted infrared with 1500 W/m 2 , and the electrical energy of 61.63% was replaced by solar thermal energy supplied by the SFPC during fish drying. The maximum drying efficiency of 12.27% was observed in solar‐assisted infrared at 1500 W/m 2 , followed by 11.25% solar‐assisted infrared at 3000 W/m 2 . The payback period for fish drying using this dryer was found to be less than 0.64, and the benefit–cost ratio of more than 1.55, except for infrared drying without solar at 1500 W/m 2 . This study shows the successful and efficient combination of solar energy and an infrared energy source for food drying.
- 18 March 2026
- Published by Wiley in Journal of Food Process Engineering
- Vol. 49 (3) , e70430
Comparative Studies of Different Drying Methods on Turmeric Slices and Rhizomes: Effect on Drying Kinetics, Quality, Modelling, and Economic Feasibility
Turmeric drying is a critical post‐harvest operation that affects product quality, shelf life, and market value. Traditional sun drying (widely used in rural areas) is slow and contamination‐prone, while conventional hot air drying (though effective) is energy‐intensive and costly. The existing studies often focus on single drying methods or do not simultaneously evaluate drying kinetics, moisture diffusivity, and quality attributes. This study addresses this gap by systematically investigating turmeric slices (5 and 10 mm) and whole rhizomes under three drying systems such as sun, solar, and hot air at two bed thicknesses (25 and 50 mm). The drying behavior was analyzed using moisture ratio, drying rate, and seven thin‐layer models, with the page model best describing sliced turmeric and the two‐term exponential model fitting whole rhizomes. Effective moisture diffusivity ranged from 7.61 × 10 −11 to 5.81 × 10 −10 m 2 /s highest under hot air drying. The quality assessment revealed that hot air drying achieved superior curcumin retention, oleoresin yield, starch content, and color preservation while solar drying provided a sustainable and cost‐effective alternative outperforming sun drying. The novelty of this study lies in its comprehensive comparison of drying methods integrating kinetics, diffusivity, and quality, and highlighting solar drying as a practical solution for small‐scale and rural processing units. It paves the way for hybrid drying technologies that optimize both efficiency and product quality.
- 18 March 2026
- Published by Wiley in Journal of Food Process Engineering
- Vol. 49 (3) , e70430
Comparative Studies of Different Drying Methods on Turmeric Slices and Rhizomes: Effect on Drying Kinetics, Quality, Modelling, and Economic Feasibility
Turmeric drying is a critical post‐harvest operation that affects product quality, shelf life, and market value. Traditional sun drying (widely used in rural areas) is slow and contamination‐prone, while conventional hot air drying (though effective) is energy‐intensive and costly. The existing studies often focus on single drying methods or do not simultaneously evaluate drying kinetics, moisture diffusivity, and quality attributes. This study addresses this gap by systematically investigating turmeric slices (5 and 10 mm) and whole rhizomes under three drying systems such as sun, solar, and hot air at two bed thicknesses (25 and 50 mm). The drying behavior was analyzed using moisture ratio, drying rate, and seven thin‐layer models, with the page model best describing sliced turmeric and the two‐term exponential model fitting whole rhizomes. Effective moisture diffusivity ranged from 7.61 × 10 −11 to 5.81 × 10 −10 m 2 /s highest under hot air drying. The quality assessment revealed that hot air drying achieved superior curcumin retention, oleoresin yield, starch content, and color preservation while solar drying provided a sustainable and cost‐effective alternative outperforming sun drying. The novelty of this study lies in its comprehensive comparison of drying methods integrating kinetics, diffusivity, and quality, and highlighting solar drying as a practical solution for small‐scale and rural processing units. It paves the way for hybrid drying technologies that optimize both efficiency and product quality.
- 7 February 2026
- Published by Taylor & Francis in Journal of Aquatic Food Product Technology
- Vol. 35 (2) , 110-135
Effect of Blanching Conditions on the Quality of Infrared-Dried Squid Rings: Sensory-Based Optimization and Semi-Empirical Drying Modeling
- 7 February 2026
- Published by Taylor & Francis in Journal of Aquatic Food Product Technology
- Vol. 35 (2) , 110-135
Effect of Blanching Conditions on the Quality of Infrared-Dried Squid Rings: Sensory-Based Optimization and Semi-Empirical Drying Modeling
- 31 January 2026
- Published by Wiley in Heat Transfer
- Vol. 55 (3) , 1718-1757
Drying of Onion and Onion Slices: Comparative Methods and Their Impact on Kinetics, Quality, Nutritional Properties, Modelling, Drying Efficiency, and Energy Consumption: A Review
Onion drying is an essential post‐harvest process that extends shelf life and preserves the nutritional, functional, and sensory qualities of onions. This review evaluates the influence of various pretreatments (brining, thermal, non‐thermal, and potassium metabisulfite) and drying methods (open sun, solar, convective, microwave, and freeze drying) on drying kinetics, quality characteristics, energy efficiency, and cost economics. Among pretreatments, blanching and ultrasound notably improved drying efficiency by enhancing moisture diffusion, reducing drying time, and maintaining product quality. Conventional drying methods, such as sun and hot‐air drying, are simple and low‐cost but often lead to nutrient degradation, color changes, and reduced sensory appeal. In contrast, advanced and hybrid drying technologies (vacuum, freeze, and low‐pressure superheated steam drying) ensure better retention of bioactive compounds, thiosulphinates, and aroma while improving rehydration capacity. However, these techniques are often limited by high energy requirements and scalability issues. Hybrid drying systems provide the most effective compromise between product quality and energy efficiency, achieving higher moisture removal with reduced specific energy consumption. Mathematical models, particularly thin‐layer (Page, Logarithmic) are used for predicting drying behavior and optimizing parameters. High‐temperature drying can cause color darkening and volatile losses, whereas low‐temperature or vacuum‐based drying better preserves phenolics, vitamin C, and aroma. Overall, integrating optimized pre‐treatments with hybrid or energy‐efficient drying technologies can produce superior‐quality dried onion products while minimizing energy use and processing costs, supporting sustainable and scalable industrial drying operations.
- 31 January 2026
- Published by Wiley in Heat Transfer
- Vol. 55 (3) , 1718-1757
Drying of Onion and Onion Slices: Comparative Methods and Their Impact on Kinetics, Quality, Nutritional Properties, Modelling, Drying Efficiency, and Energy Consumption: A Review
Onion drying is an essential post‐harvest process that extends shelf life and preserves the nutritional, functional, and sensory qualities of onions. This review evaluates the influence of various pretreatments (brining, thermal, non‐thermal, and potassium metabisulfite) and drying methods (open sun, solar, convective, microwave, and freeze drying) on drying kinetics, quality characteristics, energy efficiency, and cost economics. Among pretreatments, blanching and ultrasound notably improved drying efficiency by enhancing moisture diffusion, reducing drying time, and maintaining product quality. Conventional drying methods, such as sun and hot‐air drying, are simple and low‐cost but often lead to nutrient degradation, color changes, and reduced sensory appeal. In contrast, advanced and hybrid drying technologies (vacuum, freeze, and low‐pressure superheated steam drying) ensure better retention of bioactive compounds, thiosulphinates, and aroma while improving rehydration capacity. However, these techniques are often limited by high energy requirements and scalability issues. Hybrid drying systems provide the most effective compromise between product quality and energy efficiency, achieving higher moisture removal with reduced specific energy consumption. Mathematical models, particularly thin‐layer (Page, Logarithmic) are used for predicting drying behavior and optimizing parameters. High‐temperature drying can cause color darkening and volatile losses, whereas low‐temperature or vacuum‐based drying better preserves phenolics, vitamin C, and aroma. Overall, integrating optimized pre‐treatments with hybrid or energy‐efficient drying technologies can produce superior‐quality dried onion products while minimizing energy use and processing costs, supporting sustainable and scalable industrial drying operations.
- 4 August 2025
- Published by Wiley in Heat Transfer
- Vol. 54 (7) , 4207-4222
Experimental Evaluation of Hot Air‐Assisted Continuous Microwave Drying of Oyster Mushroom (Pleurotus ostreatus)
This study evaluated the efficiency of hot air−assisted continuous microwave (HACM) drying for oyster mushrooms (Pleurotus ostreatus), focusing on drying kinetics, quality attributes, and economic feasibility. Response surface methodology was used to optimize drying parameters viz., microwave power (600–1000 W), air temperature (40°C–60°C), and airflow rate (0.5–1.5 m/s), to minimize drying time and water activity while maximizing rehydration ratio. Optimal conditions obtained were air temperature, microwave power, and air flow rate of 55.05°C, 1000 W, 0.81 m/s, respectively, with a drying time of 5 h, water activity of 0.532, and rehydration ratio of 2.49. The dried mushrooms showed 29.63% shrinkage, a total color change of 28.51, pore sizes of 2.06–15.70 µm, and a sensory acceptability score of 8.1. Proximate analysis indicated enhanced protein (33.21%) and carbohydrate (47.34%) contents. The HACM system achieved energy efficiency and specific energy consumption of 23.12% and 2.71 kWh/kg, respectively. The benefit‐cost ratio of 1.55 and a payback period of 2.56 years confirmed the economic viability of the system and its potential for scalable and high‐quality mushroom preservation.
- 4 August 2025
- Published by Wiley in Heat Transfer
- Vol. 54 (7) , 4207-4222
Experimental Evaluation of Hot Air‐Assisted Continuous Microwave Drying of Oyster Mushroom (Pleurotus ostreatus)
This study evaluated the efficiency of hot air−assisted continuous microwave (HACM) drying for oyster mushrooms (Pleurotus ostreatus), focusing on drying kinetics, quality attributes, and economic feasibility. Response surface methodology was used to optimize drying parameters viz., microwave power (600–1000 W), air temperature (40°C–60°C), and airflow rate (0.5–1.5 m/s), to minimize drying time and water activity while maximizing rehydration ratio. Optimal conditions obtained were air temperature, microwave power, and air flow rate of 55.05°C, 1000 W, 0.81 m/s, respectively, with a drying time of 5 h, water activity of 0.532, and rehydration ratio of 2.49. The dried mushrooms showed 29.63% shrinkage, a total color change of 28.51, pore sizes of 2.06–15.70 µm, and a sensory acceptability score of 8.1. Proximate analysis indicated enhanced protein (33.21%) and carbohydrate (47.34%) contents. The HACM system achieved energy efficiency and specific energy consumption of 23.12% and 2.71 kWh/kg, respectively. The benefit‐cost ratio of 1.55 and a payback period of 2.56 years confirmed the economic viability of the system and its potential for scalable and high‐quality mushroom preservation.
- 24 April 2025
- Published by Springer Nature in Journal of Food Science and Technology
- Vol. 63 (6) , 1073-1082
Development of pilot scale, conveyor type infrared dryer and performance assessment by clam drying
A conveyor type infrared dryer with hot air assistance was designed and fabricated for fish drying purposes. The performance of the dryer was assessed by drying the clam samples at various IR intensities (1500 and 3000 W/m2), air temperature of 55 °C, IR source distance 10 cm. The drying kinetics curves were plotted and the physical, quality parameters were evaluated in the clams dried at two IR intensities. The drying time of 5 h and 4 h were noted for the clam dried at 1500 and 3000 W/m2, respectively to attain the required final moisture of 10–15%wb. Increase in IR intensity increased the drying efficiency (52.42%) and decreased the time of drying (25%) and specific energy consumption (76.65%). The Midilli model showed best fit to explain the drying characteristics of the clam in IR dryer at both intensities with highest R2 values (0.999), and lowest RMSE (6.23 × 10−5, 9.38 × 10−5), χ2 (8.90 × 10−6, 1.88 × 10−5) values. The developed dryer is found to be suitable for commercial level production of dried clam in continuous mode. Moreover, this dryer can be utilized for the drying of other food products with specific operating conditions.
- 24 April 2025
- Published by Springer Nature in Journal of Food Science and Technology
- Vol. 63 (6) , 1073-1082
Development of pilot scale, conveyor type infrared dryer and performance assessment by clam drying
A conveyor type infrared dryer with hot air assistance was designed and fabricated for fish drying purposes. The performance of the dryer was assessed by drying the clam samples at various IR intensities (1500 and 3000 W/m2), air temperature of 55 °C, IR source distance 10 cm. The drying kinetics curves were plotted and the physical, quality parameters were evaluated in the clams dried at two IR intensities. The drying time of 5 h and 4 h were noted for the clam dried at 1500 and 3000 W/m2, respectively to attain the required final moisture of 10–15%wb. Increase in IR intensity increased the drying efficiency (52.42%) and decreased the time of drying (25%) and specific energy consumption (76.65%). The Midilli model showed best fit to explain the drying characteristics of the clam in IR dryer at both intensities with highest R2 values (0.999), and lowest RMSE (6.23 × 10−5, 9.38 × 10−5), χ2 (8.90 × 10−6, 1.88 × 10−5) values. The developed dryer is found to be suitable for commercial level production of dried clam in continuous mode. Moreover, this dryer can be utilized for the drying of other food products with specific operating conditions.