Victor Grishkov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Victor Grishkov has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Aleksandr Ivanovich Lotkov
Institute of Strength Physics and Materials Science, Siberian Branch, Russian Academy of Sciences, Tomsk, Russia
9 shared publications - Dorzhima Zhapova
Institute of Strength Physics and Materials Science, Siberian Branch, Russian Academy of Sciences, Tomsk, Russia
8 shared publications - Angelina Gusarenko
Institute of Strength Physics and Materials Science, Siberian Branch, Russian Academy of Sciences, Tomsk, Russia
7 shared publications - Dmitrii Bobrov
Institute of Strength Physics and Materials Science, Siberian Branch, Russian Academy of Sciences, Tomsk, Russia
4 shared publications - Natalia Girsova
Institute of Strength Physics and Materials Science, the Siberian Branch of the Russian Academy of Science, 634055 Tomsk, Russia
4 shared publications - Victor Timkin
Russian Academy of Sciences
3 shared publications
Latest Publications
- 24 September 2025
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 16 (5) , 1468-1476
Martensitic Transformations and Inelastic Properties of TiNi Alloy Undergoing abc Pressing at 300°C
The effect of multi-axis forging (abc pressing) at 300°C on the temperatures of martensitic transformations and inelastic properties (effects of superelasticity and the shape memory) is explored in Ti49.8Ni50.2 (at %) alloy samples. It is found that the temperature of the onset of direct martensitic transformation B2 → R remains virtually the same after abc pressing. This temperature is equal to 63 ± 1°C. At the same time, the temperature of the end of the direct martensitic transformation to the B19′ structure decreases by 41 ± 1°C. The temperatures of the beginning and the end of the reverse martensitic transformation B19′ → B2 decrease by 18 and 13°C, respectively. It is found that, after abc pressing at 300°C, the alloy samples retain inelastic properties, having values (regardless of the given true strain e) comparable with the value of the inelastic properties of the coarse-grained samples. In all samples under study, the maximum value of the reversible inelastic strain reaches ~18% and is observed at 16–24% of the determined plastic torsional strain.
- 24 September 2025
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 16 (5) , 1468-1476
Martensitic Transformations and Inelastic Properties of TiNi Alloy Undergoing abc Pressing at 300°C
The effect of multi-axis forging (abc pressing) at 300°C on the temperatures of martensitic transformations and inelastic properties (effects of superelasticity and the shape memory) is explored in Ti49.8Ni50.2 (at %) alloy samples. It is found that the temperature of the onset of direct martensitic transformation B2 → R remains virtually the same after abc pressing. This temperature is equal to 63 ± 1°C. At the same time, the temperature of the end of the direct martensitic transformation to the B19′ structure decreases by 41 ± 1°C. The temperatures of the beginning and the end of the reverse martensitic transformation B19′ → B2 decrease by 18 and 13°C, respectively. It is found that, after abc pressing at 300°C, the alloy samples retain inelastic properties, having values (regardless of the given true strain e) comparable with the value of the inelastic properties of the coarse-grained samples. In all samples under study, the maximum value of the reversible inelastic strain reaches ~18% and is observed at 16–24% of the determined plastic torsional strain.
- 24 August 2024
- Published by Springer Nature in Russian Physics Journal
- Vol. 67 (8) , 1-7
Actual Yield Stress in Ti49.3Ni50.7 (at.%) Alloy in the State As Received from the Manufacturer
- 24 August 2024
- Published by Springer Nature in Russian Physics Journal
- Vol. 67 (8) , 1-7
Actual Yield Stress in Ti49.3Ni50.7 (at.%) Alloy in the State As Received from the Manufacturer
- 1 April 2024
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 15 (2) , 489-497
Features of the Grain-Subgrain Structure of Ti49.8Ni50.2 Alloy after Megaplastic Deformation by abc Pressing and Subsequent Annealing
Using the backscattered electron diffraction method, the features of grain-subgrain structure of the Ti49.8Ni50.2 (at %) alloy after megaplastic deformation by multiaxial forging (abc pressing) at 573 K and subsequent annealing were studied. It has been shown that the best detection of patterns of grain-subgrain structure of the Ti49.8Ni50.2 alloy after a given true deformation of e = 9.55 and annealing at 773 K for 2 h is observed in zones without martensitic relief on the surface of a samples. The clearest backscattered electron diffraction patterns are observed in the central part of grains, and the quality of the Kikuchi lines deteriorates with distance from the grain center. Calculation based on the equivalent grain diameter showed that the average grain size is 0.203 ± 0.053 μm. Grains are mainly elliptical in shape with an axial ratio of 0.48. Elongated grains along their length have a discrete-continuous misorientation of the crystal structure, which can reach 5 degrees per 1 μm.
- 1 April 2024
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 15 (2) , 489-497
Features of the Grain-Subgrain Structure of Ti49.8Ni50.2 Alloy after Megaplastic Deformation by abc Pressing and Subsequent Annealing
Using the backscattered electron diffraction method, the features of grain-subgrain structure of the Ti49.8Ni50.2 (at %) alloy after megaplastic deformation by multiaxial forging (abc pressing) at 573 K and subsequent annealing were studied. It has been shown that the best detection of patterns of grain-subgrain structure of the Ti49.8Ni50.2 alloy after a given true deformation of e = 9.55 and annealing at 773 K for 2 h is observed in zones without martensitic relief on the surface of a samples. The clearest backscattered electron diffraction patterns are observed in the central part of grains, and the quality of the Kikuchi lines deteriorates with distance from the grain center. Calculation based on the equivalent grain diameter showed that the average grain size is 0.203 ± 0.053 μm. Grains are mainly elliptical in shape with an axial ratio of 0.48. Elongated grains along their length have a discrete-continuous misorientation of the crystal structure, which can reach 5 degrees per 1 μm.
- Open Access
Effect of Isochronous Annealings on the Microstructure and Mechanical Properties of the Ti49.8Ni50.2 (at.%) Alloy after abc Pressing at 573 K
The regularities and features of the evolution of the grain–subgrain structure, phase composition and mechanical properties in Ti49.8Ni50.2 (at.%), depending on the temperature of isochronous annealings at 573–973 K are herein studied. The state of the Ti49.8Ni50.2 (at.%) alloy samples after abc pressing at T = 573 K with the given true strain e = 9.55 was taken as the initial state. It is shown that the grain–subgrain structure of the samples after annealing for 1 h in the temperature range of 573–673 K changes slightly. In samples annealed at 673 K, regions with the microband structure similar to the microstructure of a fast-frozen turbulent liquid flow were found. It has been established that during annealing at 773 K the beginning of an active recrystallization process is realized; the size of grains does not exceed the submicrocrystalline scale (~200 nm). At 873 K, the recrystallization process occurs in the entire volume of the samples; the grains with an average size of 2 ± 0.5 µm are almost equiaxed. The microstructure of the samples after annealing at 973 K (with average grain sizes of 5 ± 0.5 µm) is qualitatively similar to the microstructure of the samples after annealing at 873 K. It was found that the phase composition of the samples as a result of isochronous annealing at 573–973 K changes from R and B19’ immediately after abc pressing to a three-phase state: B2, R and B19’ phases. It is shown that the highest values of yield stress σy, ultimate tensile strength σUTS (1043 MPa and 1232 MPa, correspondingly) and low ductility (the deformation to fracture εf = 48%) are observed in the initial samples. Increasing the temperature of post-deformation annealing and, correspondingly, the development of recrystallization, led to a decrease in σy, σUTS and an increase in εf to the values of these characteristics in the coarse-grained samples (σy = 400 MPa, σUTS = 920 MPa and εf = 90%).
Open AccessEffect of Isochronous Annealings on the Microstructure and Mechanical Properties of the Ti49.8Ni50.2 (at.%) Alloy after abc Pressing at 573 K
The regularities and features of the evolution of the grain–subgrain structure, phase composition and mechanical properties in Ti49.8Ni50.2 (at.%), depending on the temperature of isochronous annealings at 573–973 K are herein studied. The state of the Ti49.8Ni50.2 (at.%) alloy samples after abc pressing at T = 573 K with the given true strain e = 9.55 was taken as the initial state. It is shown that the grain–subgrain structure of the samples after annealing for 1 h in the temperature range of 573–673 K changes slightly. In samples annealed at 673 K, regions with the microband structure similar to the microstructure of a fast-frozen turbulent liquid flow were found. It has been established that during annealing at 773 K the beginning of an active recrystallization process is realized; the size of grains does not exceed the submicrocrystalline scale (~200 nm). At 873 K, the recrystallization process occurs in the entire volume of the samples; the grains with an average size of 2 ± 0.5 µm are almost equiaxed. The microstructure of the samples after annealing at 973 K (with average grain sizes of 5 ± 0.5 µm) is qualitatively similar to the microstructure of the samples after annealing at 873 K. It was found that the phase composition of the samples as a result of isochronous annealing at 573–973 K changes from R and B19’ immediately after abc pressing to a three-phase state: B2, R and B19’ phases. It is shown that the highest values of yield stress σy, ultimate tensile strength σUTS (1043 MPa and 1232 MPa, correspondingly) and low ductility (the deformation to fracture εf = 48%) are observed in the initial samples. Increasing the temperature of post-deformation annealing and, correspondingly, the development of recrystallization, led to a decrease in σy, σUTS and an increase in εf to the values of these characteristics in the coarse-grained samples (σy = 400 MPa, σUTS = 920 MPa and εf = 90%).
- Open Access
Mechanical Properties of the Ti49.8Ni50.2 Alloy after Multi-Axial Forging at 573 K
The mechanical properties of Ti49.8Ni50.2 (at %) alloy under tension at room temperature are studied in dependence on the true strain (e = 1.84–9.55) specified during isothermal multi-axial forging (abc-pressing). It was found that the stress at the beginning of the pseudoyield plateau does not depend on the value of the true abc-strain. It was found that after abs-pressing, already at a true strain e = 1.84, the yield stress σy was 900 ± 25 MPa, which is more than twice as high as compared to σy in the initial state of the specimens. With a further increase in the abc-strain, the yield stress continues to increase slightly and reaches 1000 ± 25 MPa at e = 9.55. In this case, the ultimate tensile strength of the samples increases by about 15%. The strain-hardening coefficient ϴ = dσ/dε at the III (linear) stage of the σ(ε) curve has a similar dependence on e. It is shown that after abc-pressing with e from 1.84 to 9.55, the yield stress and ultimate tensile increase linearly with increasing d−1/2 in accordance with the Hall–Petch relation, where d is the average grain–subgrain size.
Open AccessMechanical Properties of the Ti49.8Ni50.2 Alloy after Multi-Axial Forging at 573 K
The mechanical properties of Ti49.8Ni50.2 (at %) alloy under tension at room temperature are studied in dependence on the true strain (e = 1.84–9.55) specified during isothermal multi-axial forging (abc-pressing). It was found that the stress at the beginning of the pseudoyield plateau does not depend on the value of the true abc-strain. It was found that after abs-pressing, already at a true strain e = 1.84, the yield stress σy was 900 ± 25 MPa, which is more than twice as high as compared to σy in the initial state of the specimens. With a further increase in the abc-strain, the yield stress continues to increase slightly and reaches 1000 ± 25 MPa at e = 9.55. In this case, the ultimate tensile strength of the samples increases by about 15%. The strain-hardening coefficient ϴ = dσ/dε at the III (linear) stage of the σ(ε) curve has a similar dependence on e. It is shown that after abc-pressing with e from 1.84 to 9.55, the yield stress and ultimate tensile increase linearly with increasing d−1/2 in accordance with the Hall–Petch relation, where d is the average grain–subgrain size.
- Open Access
Crystal Structure Defects in Titanium Nickelide after Abc Pressing at Lowered Temperature
The experimental results regarding the effect of warm (573 K) abc pressing with an increase in the specified true strain, e, up to 9.55, on the microstructure and crystal structure defects (dislocations, vacancies) of the Ti49.8Ni50.2 (at %) alloy are presented. It is shown that all samples (regardless of e) have a two-level microstructure. The grains–subgrains of the submicrocrystalline scale level are in the volumes of large grains. The average sizes of both large grains and subgrain grains decrease with increasing e to 9.55 (from 27 to 12 µm and from 0.36 to 0.13 µm, respectively). All samples had a two-phase state (rhombohedral R and monoclinic B19′ martensitic phases) at 295 K. The full-profile analysis of X-ray reflections of the B2 phase obtained at 393 K shows that the dislocation density increases from 1014 m−2 to 1015 m−2 after pressing with e = 1.84 and reaches 2·1015 m−2 when e increases to 9.55. It has been established by positron annihilation lifetime spectroscopy that dislocations are the main type of defects in initial samples and the only type of defects in samples after abc pressing. The lifetime of positrons trapped by dislocations is 166 ps, and the intensity of this component increases from 83% in the initial samples to 99.4% after pressing with e = 9.55. The initial samples contain a component with a positron lifetime of 192 ps (intensity 16.4%), which corresponds to the presence of monovacancies in the nickel sublattice of the B2 phase (concentration ≈10−5). This component is absent in the positron lifetime spectra in the samples after pressing. The results of the analysis of the Doppler broadening spectroscopy correlate with the data obtained by the positron annihilation lifetime spectroscopy.
Open AccessCrystal Structure Defects in Titanium Nickelide after Abc Pressing at Lowered Temperature
The experimental results regarding the effect of warm (573 K) abc pressing with an increase in the specified true strain, e, up to 9.55, on the microstructure and crystal structure defects (dislocations, vacancies) of the Ti49.8Ni50.2 (at %) alloy are presented. It is shown that all samples (regardless of e) have a two-level microstructure. The grains–subgrains of the submicrocrystalline scale level are in the volumes of large grains. The average sizes of both large grains and subgrain grains decrease with increasing e to 9.55 (from 27 to 12 µm and from 0.36 to 0.13 µm, respectively). All samples had a two-phase state (rhombohedral R and monoclinic B19′ martensitic phases) at 295 K. The full-profile analysis of X-ray reflections of the B2 phase obtained at 393 K shows that the dislocation density increases from 1014 m−2 to 1015 m−2 after pressing with e = 1.84 and reaches 2·1015 m−2 when e increases to 9.55. It has been established by positron annihilation lifetime spectroscopy that dislocations are the main type of defects in initial samples and the only type of defects in samples after abc pressing. The lifetime of positrons trapped by dislocations is 166 ps, and the intensity of this component increases from 83% in the initial samples to 99.4% after pressing with e = 9.55. The initial samples contain a component with a positron lifetime of 192 ps (intensity 16.4%), which corresponds to the presence of monovacancies in the nickel sublattice of the B2 phase (concentration ≈10−5). This component is absent in the positron lifetime spectra in the samples after pressing. The results of the analysis of the Doppler broadening spectroscopy correlate with the data obtained by the positron annihilation lifetime spectroscopy.
- Open Access
Structure and Phase State of Ti49.4Ni50.6 (at%) Hydrogenated in Normal Saline
The paper analyzes the surface structure and phase state of Ti49.4Ni50.6 (at%) hydrogenated at 295 K in normal saline (0.9% NaCl aqueous solution with pH = 5.7) at 20 A/m2 for 0.5–6 h. The analysis shows that the average hydrogen concentration in the alloy increases with the hydrogenation time tH as follows: slowly to 50 ppm at tH = 0.5–1.5 h, steeply to 150 ppm at tH = 1.2–2 h, and linearly to 300 ppm at tH = 2–6 h. According to Bragg–Brentano X-ray diffraction data (θ–2 θ, 2 θ ≤ 50°, CoKα radiation), the alloy in its scanned surface layer of thickness ~5.6 µm reveals a TiNiHx phase with x = 0.64 and x = 0.54 after hydrogenation for 4 and 6 h, respectively. The structure of this phase is identifiable as an orthorhombic hydride similar to β1–TiFeH0.94 (space group Pmcm), rather than as a tetragonal TiNiHx hydride with x = 0.30–1.0 (space group I4/mmm). Time curves are presented to trace the lattice parameters and volume change during the formation of such an orthorhombic phase from the initial cubic B2 phase in Ti49.4Ni50.6 (at%).
Open AccessStructure and Phase State of Ti49.4Ni50.6 (at%) Hydrogenated in Normal Saline
The paper analyzes the surface structure and phase state of Ti49.4Ni50.6 (at%) hydrogenated at 295 K in normal saline (0.9% NaCl aqueous solution with pH = 5.7) at 20 A/m2 for 0.5–6 h. The analysis shows that the average hydrogen concentration in the alloy increases with the hydrogenation time tH as follows: slowly to 50 ppm at tH = 0.5–1.5 h, steeply to 150 ppm at tH = 1.2–2 h, and linearly to 300 ppm at tH = 2–6 h. According to Bragg–Brentano X-ray diffraction data (θ–2 θ, 2 θ ≤ 50°, CoKα radiation), the alloy in its scanned surface layer of thickness ~5.6 µm reveals a TiNiHx phase with x = 0.64 and x = 0.54 after hydrogenation for 4 and 6 h, respectively. The structure of this phase is identifiable as an orthorhombic hydride similar to β1–TiFeH0.94 (space group Pmcm), rather than as a tetragonal TiNiHx hydride with x = 0.30–1.0 (space group I4/mmm). Time curves are presented to trace the lattice parameters and volume change during the formation of such an orthorhombic phase from the initial cubic B2 phase in Ti49.4Ni50.6 (at%).
- Open Access
Nanostructured Coatings (Ti,Zr)N as a Barrier to Hydrogen Diffusion into Ti0.16Pd (wt.%) Alloy
The results of a study of structure, phase, and chemical compositions of nanostructured (Ti,Zr)N coatings formed by vacuum arc deposition on Ti0.16Pd (wt.%) alloy substrates are reported. The coating composition was varied depending on the quasi-binary system δ—TiN—δ—ZrN. The coatings were formed in two modes: without (mode 1) and with (mode 2) rotation of the substrates in a plasma flow. It was shown that irrespective of the deposition regime, the coatings have a single-phase nanograined (grain size ≤ 20 nm) structure of δ-nitrides TiN, (Ti,Zr)N, and ZrN. It is found out that the coatings deposited in accordance with modes 1 and 2 significantly differ in their microstructure. It is demonstrated that in the case of electrolytic hydrogenation in a physiological saline solution (0.9% NaCl), the barrier properties of the coatings deposited via mode 2 are substantially better than those deposited via mode 1 (irrespective of the chemical coating compositions). In the coatings with a regular columnar structure (mode 1), there is a high concentration of hydrogen homogeneously distributed over the coating thickness. In the coatings formed via mode 2 (without columnar microstructure), a high concentration of hydrogen was observed in the subsurface area only. It is found out that there is no hydrogen diffusion into the substrate of these coating both immediately after hydrogenation and after storing for 430 h at room temperature. It was shown that the highest barrier properties were exhibited by the (Ti,Zr)N coatings with the least correlation of spatial distribution of nanograins and Zr/Ti ≤ 1. The hydrogen absorption in the coating based on zirconium nitride increases by a factor of 2.
Open AccessNanostructured Coatings (Ti,Zr)N as a Barrier to Hydrogen Diffusion into Ti0.16Pd (wt.%) Alloy
The results of a study of structure, phase, and chemical compositions of nanostructured (Ti,Zr)N coatings formed by vacuum arc deposition on Ti0.16Pd (wt.%) alloy substrates are reported. The coating composition was varied depending on the quasi-binary system δ—TiN—δ—ZrN. The coatings were formed in two modes: without (mode 1) and with (mode 2) rotation of the substrates in a plasma flow. It was shown that irrespective of the deposition regime, the coatings have a single-phase nanograined (grain size ≤ 20 nm) structure of δ-nitrides TiN, (Ti,Zr)N, and ZrN. It is found out that the coatings deposited in accordance with modes 1 and 2 significantly differ in their microstructure. It is demonstrated that in the case of electrolytic hydrogenation in a physiological saline solution (0.9% NaCl), the barrier properties of the coatings deposited via mode 2 are substantially better than those deposited via mode 1 (irrespective of the chemical coating compositions). In the coatings with a regular columnar structure (mode 1), there is a high concentration of hydrogen homogeneously distributed over the coating thickness. In the coatings formed via mode 2 (without columnar microstructure), a high concentration of hydrogen was observed in the subsurface area only. It is found out that there is no hydrogen diffusion into the substrate of these coating both immediately after hydrogenation and after storing for 430 h at room temperature. It was shown that the highest barrier properties were exhibited by the (Ti,Zr)N coatings with the least correlation of spatial distribution of nanograins and Zr/Ti ≤ 1. The hydrogen absorption in the coating based on zirconium nitride increases by a factor of 2.
- Open Access
Behavior of Inelastic and Plastic Strains in Coarse-Grained Ti49.3Ni50.7(at%) Alloy Deformed in B2 States
The regularities of the change in inelastic strain in coarse-grained samples of the Ti49.3Ni50.7 (at%) alloy are studied when the samples are given torsional strain in the state of the high-temperature B2 phase. During cooling and heating, the investigated samples underwent the B2–B19′ martensite transformation (MT); the temperature of the end of the reverse MT was Af = 273 K. It was found that at the temperature of isothermal cycles “loading-unloading” Af + 8 K, when the specimen is assigned a strain of 4%, the effect of superelasticity is observed. With an increase in the torsional strain, the shape memory effect is clearly manifested. It is assumed that the stabilization of the B19′ phase in unloaded samples is due to the appearance of dislocations during deformation due to high internal stresses at the interphase boundaries of the B2 phase and the martensite phase during MT. The appearance of dislocations during the loading of samples near the temperatures of forward and reverse MT can also be facilitated by the “softening” of the elastic moduli of the alloy in this temperature range. At a test temperature above Af + 26 K, the superelasticity effect dominates in the studied samples.
Open AccessBehavior of Inelastic and Plastic Strains in Coarse-Grained Ti49.3Ni50.7(at%) Alloy Deformed in B2 States
The regularities of the change in inelastic strain in coarse-grained samples of the Ti49.3Ni50.7 (at%) alloy are studied when the samples are given torsional strain in the state of the high-temperature B2 phase. During cooling and heating, the investigated samples underwent the B2–B19′ martensite transformation (MT); the temperature of the end of the reverse MT was Af = 273 K. It was found that at the temperature of isothermal cycles “loading-unloading” Af + 8 K, when the specimen is assigned a strain of 4%, the effect of superelasticity is observed. With an increase in the torsional strain, the shape memory effect is clearly manifested. It is assumed that the stabilization of the B19′ phase in unloaded samples is due to the appearance of dislocations during deformation due to high internal stresses at the interphase boundaries of the B2 phase and the martensite phase during MT. The appearance of dislocations during the loading of samples near the temperatures of forward and reverse MT can also be facilitated by the “softening” of the elastic moduli of the alloy in this temperature range. At a test temperature above Af + 26 K, the superelasticity effect dominates in the studied samples.