Florentinus Firdiyono
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Florentinus Firdiyono has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Agus Budi Prasetyo
Center of Minerals Processing and Corrosion Research, Department of Metallurgical and Materials Engineering, Universitas Indonesia, Depok 16424, Indonesia
4 shared publications - Eko Sulistiyono
Research Center for Metallurgy, National Research and Innovation Agency (BRIN), KST BJ. Habibie, Tangerang Selatan, Indonesia
4 shared publications - Eni Febriana
Prof Johny Wahyuadi Laboratory, Department of Metallurgical and Materials Engineering, Universitas Indonesia, Depok, Indonesia
4 shared publications - Johny Wahyuadi Soedarsono
University of Indonesia
3 shared publications - Murni Handayani
Research Center for Materials Science and Metallurgy, National Research and Innovation Agency (BRIN), Building 470, PUSPIPTEK Area, Tangerang Selatan, Banten, Indonesia
3 shared publications - Wahyu Mayangsari
Research Centre for Metallurgy, National Research and Innovation Agency (BRIN), Tangerang Selatan, Indonesia
3 shared publications
Latest Publications
- Open Access
- 6 February 2024
- Published by Elsevier in Case Studies in Chemical and Environmental Engineering
- Vol. 9
Novel method for minimizing reactant in the synthesis of sodium silicate solution from mixed-phase quartz-amorphous SIO2
- 6 February 2024
- Published by Elsevier in Case Studies in Chemical and Environmental Engineering
- Vol. 9
Open AccessNovel method for minimizing reactant in the synthesis of sodium silicate solution from mixed-phase quartz-amorphous SIO2
- Open Access
- 30 December 2022
- Published by National Research and Innovation Agency in Metalurgi
- Vol. 37 (3)
MORPHOLOGY AND RESISTIVITY VALUE OF FLOURINE-DOPED TIN OXIDE (FTO) USING INDONESIAN LOCAL DIMETHYLTIN DICHLORIIDE (DTMC) PRECURSORS
Transparent Conductive Oxide (TCO) is the main component for solar cell fabrication. One of the promising types of TCO is fluorine-doped tin oxide (FTO). The method used in depositing the conductive layer of FTO is spray pyrolysis with an ultrasonic nebulizer. The precursor is a local Indonesian product, dimethyl tin dichloride (DMTC), with doping ammonium fluoride (NH4F). The variable that used in this study were variations in deposition time (5. 10. 15. 20, and 25 minutes) with a fixed substrate temperature at 300°C and doping variations (un-doped, 2 wt.% doped and 8 wt.% doped) to see the effect of adding F doping to the precursor solution. The resistivity value with deposition time of 5. 10. 15. 20 and 25 minute (2 wt.% doped) is 0.218x100; 0.449x10-1; 1,567x10-2; 0.676x10-2 0.377x10-2 Ω.cm. For doping variations (un-doped, 2 wt% doped and 8 wt% doped) the value is 0.883x10-2; 0.377x10-2; 0.506x10-3 Ω.cm. There is a decreasing trend in the resistivity values obtained along with the increase in deposition time and the addition of doping to obtain better conductive properties. The grain size will increase with increasing deposition time and the addition of doping. The optimum resistivity value obtained in this study was 0.377x10-2 Ω.cm, obtained at the deposition time of 25 minutes with 2 wt.% doping.
- 30 December 2022
- Published by National Research and Innovation Agency in Metalurgi
- Vol. 37 (3)
Open AccessMORPHOLOGY AND RESISTIVITY VALUE OF FLOURINE-DOPED TIN OXIDE (FTO) USING INDONESIAN LOCAL DIMETHYLTIN DICHLORIIDE (DTMC) PRECURSORS
Transparent Conductive Oxide (TCO) is the main component for solar cell fabrication. One of the promising types of TCO is fluorine-doped tin oxide (FTO). The method used in depositing the conductive layer of FTO is spray pyrolysis with an ultrasonic nebulizer. The precursor is a local Indonesian product, dimethyl tin dichloride (DMTC), with doping ammonium fluoride (NH4F). The variable that used in this study were variations in deposition time (5. 10. 15. 20, and 25 minutes) with a fixed substrate temperature at 300°C and doping variations (un-doped, 2 wt.% doped and 8 wt.% doped) to see the effect of adding F doping to the precursor solution. The resistivity value with deposition time of 5. 10. 15. 20 and 25 minute (2 wt.% doped) is 0.218x100; 0.449x10-1; 1,567x10-2; 0.676x10-2 0.377x10-2 Ω.cm. For doping variations (un-doped, 2 wt% doped and 8 wt% doped) the value is 0.883x10-2; 0.377x10-2; 0.506x10-3 Ω.cm. There is a decreasing trend in the resistivity values obtained along with the increase in deposition time and the addition of doping to obtain better conductive properties. The grain size will increase with increasing deposition time and the addition of doping. The optimum resistivity value obtained in this study was 0.377x10-2 Ω.cm, obtained at the deposition time of 25 minutes with 2 wt.% doping.
- Open Access
- 9 September 2021
- Published by National Research and Innovation Agency in Metalurgi
- Vol. 36 (2)
The Effect of Roasting Prior to The Leaching Process of Alkalinized Ferronickel Slag Followed by Precipitation Process
Terak feronikel dihasilkan sebagai produk samping dari produksi feronikel. terak feronikel mempunyai potensi sebagai bahan baku beberapa komponen berharga karena komposisinya melalui proses bertahap. Tujuan dari penelitian ini adalah untuk mengetahui pengaruh dari proses pemanggangan campuran terak feronikel dan Na2CO3 sebelum leaching air panas dan presipitasi untuk menghasilkan endapan silika. Proses pemanggangan terak feronikel dengan penambahan Na2CO3 telah dilakukan untuk pembentukan natrium silikat. Kemudian dilarutkan melalui proses pelindian menggunakan air panas 90 ° C selama 120 menit. Endapan silika didapatkan dengan proses presipitasi sodium silikat terlarut diikuti dengan pemeraman selama tiga hari. Berdasarkan hasilnya, pemanggangan menyebabkan perubahan komposisi yang mempengaruhi persen pelindian dan perolehan silika. Reaksi terjadi dari permukaan ke inti yang dibuktikan dengan pengecilan ukuran residu pelindian dari RAF nya. Natrium silikat dalam bentuk Na4SiO4 diketahui terlarut Ketika pelindian air dilakukan. Pengendapan dan pemeraman larutan natrium silikat telah menghasilkan endapan silika dengan ukuran partikel lebih dari 100 mm. pemanggangan pada 1000 ° C selama 240 menit menghasilkan perolehan silika tertinggi.
- 9 September 2021
- Published by National Research and Innovation Agency in Metalurgi
- Vol. 36 (2)
Open AccessThe Effect of Roasting Prior to The Leaching Process of Alkalinized Ferronickel Slag Followed by Precipitation Process
Terak feronikel dihasilkan sebagai produk samping dari produksi feronikel. terak feronikel mempunyai potensi sebagai bahan baku beberapa komponen berharga karena komposisinya melalui proses bertahap. Tujuan dari penelitian ini adalah untuk mengetahui pengaruh dari proses pemanggangan campuran terak feronikel dan Na2CO3 sebelum leaching air panas dan presipitasi untuk menghasilkan endapan silika. Proses pemanggangan terak feronikel dengan penambahan Na2CO3 telah dilakukan untuk pembentukan natrium silikat. Kemudian dilarutkan melalui proses pelindian menggunakan air panas 90 ° C selama 120 menit. Endapan silika didapatkan dengan proses presipitasi sodium silikat terlarut diikuti dengan pemeraman selama tiga hari. Berdasarkan hasilnya, pemanggangan menyebabkan perubahan komposisi yang mempengaruhi persen pelindian dan perolehan silika. Reaksi terjadi dari permukaan ke inti yang dibuktikan dengan pengecilan ukuran residu pelindian dari RAF nya. Natrium silikat dalam bentuk Na4SiO4 diketahui terlarut Ketika pelindian air dilakukan. Pengendapan dan pemeraman larutan natrium silikat telah menghasilkan endapan silika dengan ukuran partikel lebih dari 100 mm. pemanggangan pada 1000 ° C selama 240 menit menghasilkan perolehan silika tertinggi.
- Open Access
- 25 June 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (5 (111)) , 6-12
Investigation of surfactant effect during synthesis of magnesium oxide nanoparticles from bittern using ultrasonic destruction process
Magnesium oxide (MgO) nanoparticles have been widely used in a variety of applications because of their good surface reactivity. Magnesium oxide from bittern has a larger surface area compared to magnesium oxide from calcined magnesite and magnesium ions precipitation from bittern using sodium hydroxide has higher purity than using calcium hydroxide or ammonium hydroxide. In this research, sodium hydroxide was added to a bittern solution obtaining magnesium hydroxide precipitate, followed by the calcination process to produce magnesium oxide. Nano magnesium oxide was synthesized by the ultrasonic destruction process using ethanol and 2-propanol as media. In this study, sonication time and particle concentration effect on the ultrasonic destruction process were investigated. During the process, the sonication time was varied between 8, 16, 32, 64, and 128 minutes while the magnesium oxide concentration was varied between 1 %, 2 %, and 3 %. Increasing sonication time and particle concentration will decrease the particle size. The previous study shows that particles with very small sizes tend to have an agglomeration effect. The aim of this work is to optimize nano magnesium oxide production from bittern. Surfactant addition was also studied to prevent agglomeration between particles. Four types of surfactant namely anionic (sodium lauryl sulfate), cationic (cetyl tri-methyl-ammonium bromide), amphoteric (fatty acid amido alkyl betaine), and non-ionic (nonylphenol 10 ethoxylated) with a concentration of 1 % and a volume of 0.125 ml were added during the second ultrasonic destruction process. All types of surfactants have a positive effect to prevent agglomeration during the ultrasonic destruction process, with the amphoteric surfactant having the highest performance
- 25 June 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (5 (111)) , 6-12
Open AccessInvestigation of surfactant effect during synthesis of magnesium oxide nanoparticles from bittern using ultrasonic destruction process
Magnesium oxide (MgO) nanoparticles have been widely used in a variety of applications because of their good surface reactivity. Magnesium oxide from bittern has a larger surface area compared to magnesium oxide from calcined magnesite and magnesium ions precipitation from bittern using sodium hydroxide has higher purity than using calcium hydroxide or ammonium hydroxide. In this research, sodium hydroxide was added to a bittern solution obtaining magnesium hydroxide precipitate, followed by the calcination process to produce magnesium oxide. Nano magnesium oxide was synthesized by the ultrasonic destruction process using ethanol and 2-propanol as media. In this study, sonication time and particle concentration effect on the ultrasonic destruction process were investigated. During the process, the sonication time was varied between 8, 16, 32, 64, and 128 minutes while the magnesium oxide concentration was varied between 1 %, 2 %, and 3 %. Increasing sonication time and particle concentration will decrease the particle size. The previous study shows that particles with very small sizes tend to have an agglomeration effect. The aim of this work is to optimize nano magnesium oxide production from bittern. Surfactant addition was also studied to prevent agglomeration between particles. Four types of surfactant namely anionic (sodium lauryl sulfate), cationic (cetyl tri-methyl-ammonium bromide), amphoteric (fatty acid amido alkyl betaine), and non-ionic (nonylphenol 10 ethoxylated) with a concentration of 1 % and a volume of 0.125 ml were added during the second ultrasonic destruction process. All types of surfactants have a positive effect to prevent agglomeration during the ultrasonic destruction process, with the amphoteric surfactant having the highest performance
- Open Access
- 18 June 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (6 (111)) , 32-40
Implementation of sulfuric acid leaching for aluminum and iron removal for improvement of low-grade silica from quartz sand of Sukabumi, Indonesia
Indonesia has very abundant reserves of silica, but progressive studies on the deposition of this material are very few, resulting in limited applications of silica. This work refers to the purification of silica from quartz sand originated from Sukabumi, Indonesia to obtain high-purity silica, which can be applied as important raw materials for special purposes. The aim of our research is to improve low-grade silica from quartz sand by removing impurities, especially aluminum and iron removal, using sulfuric acid leaching. In order to achieve the aim, the effect of reaction time and sulfuric acid concentration on the leaching process was investigated. The effectiveness of sulfuric acid for the impurities removal was observed. The chemical composition of the samples before and after leaching was studied using X-ray fluorescence. The mineralogical analysis of the starting materials and the products was conducted using X-ray diffraction. Microstructure analysis was performed using a scanning electron microscope, and EDS test was used to show the element composition at different points. The experimental results show that the optimum condition of the leaching process occurs at a reaction time of 5 hours with a sulfuric acid concentration of 10 N. The silica levels increase from 93.702 % to 96.438 %. Aluminum and iron impurities reduced from 4.691 % to 2.712 % and from 0.641 % to 0.094 %, respectively. At this optimum point, sulfuric acid is very effective to remove aluminum and iron impurities up to 42 % and 85 %, respectively. The results of this research can be a very significant opportunity to increase the value added of quartz sand from Sukabumi, which can enhance the quality of low-grade silica to provide better raw materials for glass industries.
- 18 June 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (6 (111)) , 32-40
Open AccessImplementation of sulfuric acid leaching for aluminum and iron removal for improvement of low-grade silica from quartz sand of Sukabumi, Indonesia
Indonesia has very abundant reserves of silica, but progressive studies on the deposition of this material are very few, resulting in limited applications of silica. This work refers to the purification of silica from quartz sand originated from Sukabumi, Indonesia to obtain high-purity silica, which can be applied as important raw materials for special purposes. The aim of our research is to improve low-grade silica from quartz sand by removing impurities, especially aluminum and iron removal, using sulfuric acid leaching. In order to achieve the aim, the effect of reaction time and sulfuric acid concentration on the leaching process was investigated. The effectiveness of sulfuric acid for the impurities removal was observed. The chemical composition of the samples before and after leaching was studied using X-ray fluorescence. The mineralogical analysis of the starting materials and the products was conducted using X-ray diffraction. Microstructure analysis was performed using a scanning electron microscope, and EDS test was used to show the element composition at different points. The experimental results show that the optimum condition of the leaching process occurs at a reaction time of 5 hours with a sulfuric acid concentration of 10 N. The silica levels increase from 93.702 % to 96.438 %. Aluminum and iron impurities reduced from 4.691 % to 2.712 % and from 0.641 % to 0.094 %, respectively. At this optimum point, sulfuric acid is very effective to remove aluminum and iron impurities up to 42 % and 85 %, respectively. The results of this research can be a very significant opportunity to increase the value added of quartz sand from Sukabumi, which can enhance the quality of low-grade silica to provide better raw materials for glass industries.
- Open Access
- 30 April 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (12 (110)) , 44-51
Decomposition of ferronickel slag through alkali fusion in the roasting process
Ferronickel slag is a by-product of the nickel smelting process. Recycling of ferronickel slag is required since it contains valuable elements besides its potency to pollute the environment. In order to take advantage of the valuable materials and reducing the potential hazard, beneficiation of ferronickel slag is essential. Alkali fusion of ferronickel slag using Na2CO3 in the roasting process was carried out. This study aims to determine the decomposition of the mixture of ferronickel slag-Na2CO3 in the roasting process. Roasting temperature and time were 800–1,000 °C and 60‒240 minutes, respectively. Characterizations of the ferronickel slag were conducted by XRF, ICP-OES, XRD and SEM-EDS. Meanwhile, roasted products were characterized using ICP-OES, XRD and SEM-EDS. Characterization of the ferronickel slag indicates that Mg and Si are the main elements followed by Fe, Al and Cr. Moreover, olivine is detected as the main phase. The roasting process caused percent weight loss of the roasted products, which indicates decomposition occurred and affected the elements content, phases and morphology. The roasting process at about 900 °C for 60 minutes is a preferable decomposition base on the process conditions applied and the change of elements content. Aluminum (Al) and chromium (Cr) content in the roasted products upgraded significantly compared to iron (Fe) and magnesium (Mg) content. Olivine phase transforms to some phases, which were bounded with the sodium compound such as Na2MgSiO4, Na4SiO4 and Na2CrO4. The rough layer is observed on the surface of the roasted product as a result of the decomposition process. It indicates that liquid-solid mass transfer is initiated from the surface
- 30 April 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (12 (110)) , 44-51
Open AccessDecomposition of ferronickel slag through alkali fusion in the roasting process
Ferronickel slag is a by-product of the nickel smelting process. Recycling of ferronickel slag is required since it contains valuable elements besides its potency to pollute the environment. In order to take advantage of the valuable materials and reducing the potential hazard, beneficiation of ferronickel slag is essential. Alkali fusion of ferronickel slag using Na2CO3 in the roasting process was carried out. This study aims to determine the decomposition of the mixture of ferronickel slag-Na2CO3 in the roasting process. Roasting temperature and time were 800–1,000 °C and 60‒240 minutes, respectively. Characterizations of the ferronickel slag were conducted by XRF, ICP-OES, XRD and SEM-EDS. Meanwhile, roasted products were characterized using ICP-OES, XRD and SEM-EDS. Characterization of the ferronickel slag indicates that Mg and Si are the main elements followed by Fe, Al and Cr. Moreover, olivine is detected as the main phase. The roasting process caused percent weight loss of the roasted products, which indicates decomposition occurred and affected the elements content, phases and morphology. The roasting process at about 900 °C for 60 minutes is a preferable decomposition base on the process conditions applied and the change of elements content. Aluminum (Al) and chromium (Cr) content in the roasted products upgraded significantly compared to iron (Fe) and magnesium (Mg) content. Olivine phase transforms to some phases, which were bounded with the sodium compound such as Na2MgSiO4, Na4SiO4 and Na2CrO4. The rough layer is observed on the surface of the roasted product as a result of the decomposition process. It indicates that liquid-solid mass transfer is initiated from the surface
- Open Access
- 31 January 2020
- Published by Balai Besar Pengujian Mineral dan Batubara tekMIRA in Jurnal Teknologi Mineral dan Batubara
- Vol. 16 (1) , 15-21
Probabilitas Mineral Pasir Besi Titan Yogyakarta Berdasarkan Studi pXRF
- 31 January 2020
- Published by Balai Besar Pengujian Mineral dan Batubara tekMIRA in Jurnal Teknologi Mineral dan Batubara
- Vol. 16 (1) , 15-21
Open AccessProbabilitas Mineral Pasir Besi Titan Yogyakarta Berdasarkan Studi pXRF
- Open Access
- 1 March 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 333 (1) , 012050
Phosphorus Elimination at Sodium Silicate from Quartz Sand Roasted with Complexation using Chitosan-EDTA
A phosphorus elimination from sodium silicate solution has been studied. Phosphorus elimination was performed by adding chitosan-EDTA to remove cation phosphorus. Characterization of chitosan-EDTA material was performed using FT-IR, while the decreasing level of phosphorus content was analyzed by quantitative analysis using spectrophotometer UV-Vis refers to SNI 06-6989-2004. The results showed that the content of the sodium silicate can be reduced up to 67.1% through Chitosan-EDTA complexation with phosphorus.
- 1 March 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 333 (1) , 012050
Open AccessPhosphorus Elimination at Sodium Silicate from Quartz Sand Roasted with Complexation using Chitosan-EDTA
A phosphorus elimination from sodium silicate solution has been studied. Phosphorus elimination was performed by adding chitosan-EDTA to remove cation phosphorus. Characterization of chitosan-EDTA material was performed using FT-IR, while the decreasing level of phosphorus content was analyzed by quantitative analysis using spectrophotometer UV-Vis refers to SNI 06-6989-2004. The results showed that the content of the sodium silicate can be reduced up to 67.1% through Chitosan-EDTA complexation with phosphorus.