Ihor Zaselskiy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ihor Zaselskiy has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Serhii Shved
State University of Economics and Technology
3 shared publications - Hennadii Zaitsev
Technological institute of State university of economics and technology, Kryvyi Rih
2 shared publications Dmitry Popolov
Department of metallurgical equipment , Krivoy Rog Metallurgical institute, National Metallurgical Academy of Ukraine , Stepana Tilgi, 5 , Krivoy Rog , 50006 , Ukraine
1 shared publication- Eduard Havrylov
State University of Economics and Technology
1 shared publication G. L. Zaitsev
Krivoi Rog National University
1 shared publicationIgor Pelykh
National Metallurgical Academy of Ukraine , Dnipropetrovsk , Ukraine
1 shared publication
Latest Publications
- Open Access
- 31 October 2026
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 5 (1(91)) , 6-11
Establishment of regularities in the formation of the restoring force of a ball support system of a machine with an eccentric mass
The object of research is the ball support system of a machine with an eccentric mass, which limits the transmission of horizontal dynamic loads to the foundation. The problem was not to transfer horizontal dynamic forces onto the foundation‚ thus stabilizing the machine without an increase in the structural mass of the equipment and guaranteeing adaptation to varying operating conditions․ For the analysis of the support design efficiency, a mathematical model of the restoring force depending on the weight of the machine, geometrical parameters of the support, and allowable displacement of the machine body was created. On the basis of this model, the nonlinear dependency of the restoring force and its linear approximation were obtained. Further analysis of their properties was conducted numerically by using the technical parameters of the KKD-1500/180 cone crusher. The investigation results indicate that the force which acts to restore depends only on the load caused by the weight of the machinery and the geometry of the spherical surface contacts. With the geometric coefficient of k = 1–1.5, the system has self-limited behavior in relation to the vibration amplitude of the machinery body. The analysis of the differences between the absolute values of the restoring forces obtained by both models and the relative error of the linearization demonstrated that, at low displacements δ ≤ 40 mm, the linearization error is less than 0.88%. Intermediate displacements δ = 40–80 mm and critical displacement δ = 150 mm have errors equal to 4.7% and 32%, respectively. In the last case, the linearization results in lower values of the restoring force. Thus, these relationships can be employed in the development of ball support systems that have spherical contact surfaces of machines that possess eccentric masses experiencing considerable horizontal dynamic load. When carrying out preliminary designs and during normal working conditions (δ ≤ 40 mm), the linear approximation may be regarded as sufficiently accurate. However, operating conditions close to resonance, resonance passage, and those concerning transient and emergency loads for displacements δ > 80 mm require the application of the nonlinear model.
- 31 October 2026
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 5 (1(91)) , 6-11
Open AccessEstablishment of regularities in the formation of the restoring force of a ball support system of a machine with an eccentric mass
The object of research is the ball support system of a machine with an eccentric mass, which limits the transmission of horizontal dynamic loads to the foundation. The problem was not to transfer horizontal dynamic forces onto the foundation‚ thus stabilizing the machine without an increase in the structural mass of the equipment and guaranteeing adaptation to varying operating conditions․ For the analysis of the support design efficiency, a mathematical model of the restoring force depending on the weight of the machine, geometrical parameters of the support, and allowable displacement of the machine body was created. On the basis of this model, the nonlinear dependency of the restoring force and its linear approximation were obtained. Further analysis of their properties was conducted numerically by using the technical parameters of the KKD-1500/180 cone crusher. The investigation results indicate that the force which acts to restore depends only on the load caused by the weight of the machinery and the geometry of the spherical surface contacts. With the geometric coefficient of k = 1–1.5, the system has self-limited behavior in relation to the vibration amplitude of the machinery body. The analysis of the differences between the absolute values of the restoring forces obtained by both models and the relative error of the linearization demonstrated that, at low displacements δ ≤ 40 mm, the linearization error is less than 0.88%. Intermediate displacements δ = 40–80 mm and critical displacement δ = 150 mm have errors equal to 4.7% and 32%, respectively. In the last case, the linearization results in lower values of the restoring force. Thus, these relationships can be employed in the development of ball support systems that have spherical contact surfaces of machines that possess eccentric masses experiencing considerable horizontal dynamic load. When carrying out preliminary designs and during normal working conditions (δ ≤ 40 mm), the linear approximation may be regarded as sufficiently accurate. However, operating conditions close to resonance, resonance passage, and those concerning transient and emergency loads for displacements δ > 80 mm require the application of the nonlinear model.
- Open Access
- 26 June 2024
- Published by State University Of Economics And Technology in Economics and technical engineering
- Vol. 2 (1) , 145-157
Reducing the likelihood of material hanging when loading a coarse crusher
Many years of experience in the operation of coarse cone crushers of the type KKD 1500/180 at a number of enterprises of Metinvest Kryvyi Rih has shown that when mineral raw materials are loaded into the flowing part of the crusher feed path, uneven feeding occurs as a result of large elongated pieces hanging in the intake pit, which leads to significant periods of idle and unproductive operation of crushers, resulting in significant unproductive costs for their elimination. The aim of the work was to conduct laboratory studies related to determining the reduction of the probability of formation of stable forms of material suspension when loading it into a coarse crusher. To achieve this goal, an empirical-analytical research method was used, where the hypothesis was put forward that the probability of the appearance of hang-ups in the crusher feed path can be significantly affected by the configuration of a specially configured deflector grate located in the intake pit of the raw material fed by weight to the crusher entrance. To test this hypothesis, laboratory devices have been developed that can simulate the processes of material suspension in the crusher feed path in two-dimensional and three-dimensional forms. As a result of the laboratory experiments, it was found that the configuration of the deflector grid does affect the probability of hang-ups in the feed path and their probability of hang-ups in the two-dimensional laboratory setup was reduced by 20%, and in the three-dimensional one - by 24.1% compared to the currently existing crusher feed path. The analysis of the results shows that the lowest probability of hang-ups in the three-dimensional laboratory model is provided by a transverse grate in a row with one longitudinal rod. Moreover, the contour formed by the entry points of the transverse rods of the grating into the side wall of the receiving pit should be equidistant to the contour of the rock cushion on the same wall. The distance between the equidistant and the forming curve should be at least two maximum rock block sizes. The use of such a grid can significantly reduce unproductive downtime of the crusher and significantly reduce the material costs involved in the process of crushing mineral raw materials.
- 26 June 2024
- Published by State University Of Economics And Technology in Economics and technical engineering
- Vol. 2 (1) , 145-157
Open AccessReducing the likelihood of material hanging when loading a coarse crusher
Many years of experience in the operation of coarse cone crushers of the type KKD 1500/180 at a number of enterprises of Metinvest Kryvyi Rih has shown that when mineral raw materials are loaded into the flowing part of the crusher feed path, uneven feeding occurs as a result of large elongated pieces hanging in the intake pit, which leads to significant periods of idle and unproductive operation of crushers, resulting in significant unproductive costs for their elimination. The aim of the work was to conduct laboratory studies related to determining the reduction of the probability of formation of stable forms of material suspension when loading it into a coarse crusher. To achieve this goal, an empirical-analytical research method was used, where the hypothesis was put forward that the probability of the appearance of hang-ups in the crusher feed path can be significantly affected by the configuration of a specially configured deflector grate located in the intake pit of the raw material fed by weight to the crusher entrance. To test this hypothesis, laboratory devices have been developed that can simulate the processes of material suspension in the crusher feed path in two-dimensional and three-dimensional forms. As a result of the laboratory experiments, it was found that the configuration of the deflector grid does affect the probability of hang-ups in the feed path and their probability of hang-ups in the two-dimensional laboratory setup was reduced by 20%, and in the three-dimensional one - by 24.1% compared to the currently existing crusher feed path. The analysis of the results shows that the lowest probability of hang-ups in the three-dimensional laboratory model is provided by a transverse grate in a row with one longitudinal rod. Moreover, the contour formed by the entry points of the transverse rods of the grating into the side wall of the receiving pit should be equidistant to the contour of the rock cushion on the same wall. The distance between the equidistant and the forming curve should be at least two maximum rock block sizes. The use of such a grid can significantly reduce unproductive downtime of the crusher and significantly reduce the material costs involved in the process of crushing mineral raw materials.
- Open Access
- 25 October 2023
- Published by State University Of Economics And Technology in Economics and technical engineering
- Vol. 1 (1) , 115-125
Дослідження варіантів удосконалення ґрунтового насосу для залізорудної пульпи
For pumping iron ore slurry, many mining and processing plants in Ukraine use an 8Gr-8m submersible pump. As shown its performance under the conditions of pumping pulp with a density of up to 1400 kg/m 3, they do not correspond to the passport data, and this is mainly due to concerns the flow chamber, the service life of which is reduced by almost 2 times compared to the manufacturer’s suggested service life. Therefore, the aim of the work was to study options for improving the design of the flow part of the 8Gr-8m pump, which would significantly increase its service life. To achieve this goal and obtain the required results we chose a method based on hydrodynamic studies using CAD technologies, for which, in addition to the 3D model of the existing pump, four more different designs were developed. The proposed designs were studied using SOLIDWORKS Flow Simulation program, which allowed us to model the movement of the pulp in the pump flow chamber. The parameters for modeling were selected based on pump operation conditions at the iron ore pulp pumping section concentrator of the Southern Mining and Processing Plant in Kryvyi Rih. The analysis of the results showed that the best performance is provided by a composite impeller with 4 blades of complex shape, low profile, which has a good pumping characteristic with a minimum tendency to wear. The design of the removable impeller is made of cast steel and lined with rubber, it has 4 blades with rounded front edges. The distance along the armhole between the side washers is 50 mm, it is unchanged. The pressure surface of the blade has a short ledge. The distribution zone is a high layer of small diameter. The inlet washer is flat, but with a high flap on the diffuser. The diameter of the wheel is 520 mm, and its weight is 70 kg. Based on this model, animproved design was proposed for of the flowing part of the 8GR-8m pump impeller and its lining lining based on SCS-30ARKM-15 rubber, which in combination with technical solutions allows to more effectively prevent wear of the studied unit and leads to increase its service life.
- 25 October 2023
- Published by State University Of Economics And Technology in Economics and technical engineering
- Vol. 1 (1) , 115-125
Open AccessДослідження варіантів удосконалення ґрунтового насосу для залізорудної пульпи
For pumping iron ore slurry, many mining and processing plants in Ukraine use an 8Gr-8m submersible pump. As shown its performance under the conditions of pumping pulp with a density of up to 1400 kg/m 3, they do not correspond to the passport data, and this is mainly due to concerns the flow chamber, the service life of which is reduced by almost 2 times compared to the manufacturer’s suggested service life. Therefore, the aim of the work was to study options for improving the design of the flow part of the 8Gr-8m pump, which would significantly increase its service life. To achieve this goal and obtain the required results we chose a method based on hydrodynamic studies using CAD technologies, for which, in addition to the 3D model of the existing pump, four more different designs were developed. The proposed designs were studied using SOLIDWORKS Flow Simulation program, which allowed us to model the movement of the pulp in the pump flow chamber. The parameters for modeling were selected based on pump operation conditions at the iron ore pulp pumping section concentrator of the Southern Mining and Processing Plant in Kryvyi Rih. The analysis of the results showed that the best performance is provided by a composite impeller with 4 blades of complex shape, low profile, which has a good pumping characteristic with a minimum tendency to wear. The design of the removable impeller is made of cast steel and lined with rubber, it has 4 blades with rounded front edges. The distance along the armhole between the side washers is 50 mm, it is unchanged. The pressure surface of the blade has a short ledge. The distribution zone is a high layer of small diameter. The inlet washer is flat, but with a high flap on the diffuser. The diameter of the wheel is 520 mm, and its weight is 70 kg. Based on this model, animproved design was proposed for of the flowing part of the 8GR-8m pump impeller and its lining lining based on SCS-30ARKM-15 rubber, which in combination with technical solutions allows to more effectively prevent wear of the studied unit and leads to increase its service life.
- Open Access
- 22 April 2020
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 166, 03008
The study of the lining layer abrasing wear in the semi-autogenous grinding mill
In this work complex investigations of the abrasing wear of lining of self-grinding mills (semiautogenous grinding mills) are carried out with the obtaining of mathematical models of wear-abrasing of elevators in terms of height, weight, volume and worn-out area. In particular, according to the location and nature of the abrasing wear processes, the liner-lifters mill self-grinding are identified in three typical groups. During 1 year, in the conditions of Ingulets GOK, the monitoring of the abrasing wear of selected groups of lifters of self-grinding mills was performed. On the basis of the experimental data calculationed in the Microsoft Office Excel program, a set of mathematical models of lifter abrasing wear was obtained in terms of height, weight, volume and worn-out area. The obtained dependencies are recommended for prediction of abrasing wear of lining and necessary frequency of replacement of inserts-lifters. In addition, the research of wear of lining made of cast iron RF–4, showed a significant reduction in their abrasing wear compared with steel 110G13L. Thus, it has been shown that the selection of liner-lifters materials can reduce the inter–repair period by 3 times or more (replacement of worn-out lifters). A comparison of the actual picture of the abrasing wear of elevators and Simulation Statics simulated result (using SolidWorks) stresses shows the convergence of the arrangement of the zones of maximum stresses and the maximum abrasing wear of the lining. Investigation of the influence of the stressed state of lining plates on the intensity of their abrasing wear – a promising direction for further research.
- 22 April 2020
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 166, 03008
Open AccessThe study of the lining layer abrasing wear in the semi-autogenous grinding mill
In this work complex investigations of the abrasing wear of lining of self-grinding mills (semiautogenous grinding mills) are carried out with the obtaining of mathematical models of wear-abrasing of elevators in terms of height, weight, volume and worn-out area. In particular, according to the location and nature of the abrasing wear processes, the liner-lifters mill self-grinding are identified in three typical groups. During 1 year, in the conditions of Ingulets GOK, the monitoring of the abrasing wear of selected groups of lifters of self-grinding mills was performed. On the basis of the experimental data calculationed in the Microsoft Office Excel program, a set of mathematical models of lifter abrasing wear was obtained in terms of height, weight, volume and worn-out area. The obtained dependencies are recommended for prediction of abrasing wear of lining and necessary frequency of replacement of inserts-lifters. In addition, the research of wear of lining made of cast iron RF–4, showed a significant reduction in their abrasing wear compared with steel 110G13L. Thus, it has been shown that the selection of liner-lifters materials can reduce the inter–repair period by 3 times or more (replacement of worn-out lifters). A comparison of the actual picture of the abrasing wear of elevators and Simulation Statics simulated result (using SolidWorks) stresses shows the convergence of the arrangement of the zones of maximum stresses and the maximum abrasing wear of the lining. Investigation of the influence of the stressed state of lining plates on the intensity of their abrasing wear – a promising direction for further research.
- Open Access
- 1 June 2019
- Published by Walter de Gruyter GmbH in Mechanics and Mechanical Engineering
- Vol. 23 (1) , 94-97
Studying of movement kinematics of dynamically active sieve
The article presents the movement kinematics of the modular bar element of a dynamically active polymer sieve of a vibrating screen. On the basis of analytical methods, the mathematical model was obtained, which makes it possible to determine the law and trajectory of the modular bar element movement depending on its geometric characteristics, physico-mechanical properties of the polymer material, the regime and technological parameters of the vibrating screen. The results of this research show that in the working frequency range of the vibrating screen grate, modular bar element of the dynamically active sieve moves along the trajectories, the envelope of which is represented by Cassini’s ovals, which along with the generation of the amplitude component in the horizontal and vertical directions allows one to obtain the selfcleaning effect of the sowing surface.
- 1 June 2019
- Published by Walter de Gruyter GmbH in Mechanics and Mechanical Engineering
- Vol. 23 (1) , 94-97
Open AccessStudying of movement kinematics of dynamically active sieve
The article presents the movement kinematics of the modular bar element of a dynamically active polymer sieve of a vibrating screen. On the basis of analytical methods, the mathematical model was obtained, which makes it possible to determine the law and trajectory of the modular bar element movement depending on its geometric characteristics, physico-mechanical properties of the polymer material, the regime and technological parameters of the vibrating screen. The results of this research show that in the working frequency range of the vibrating screen grate, modular bar element of the dynamically active sieve moves along the trajectories, the envelope of which is represented by Cassini’s ovals, which along with the generation of the amplitude component in the horizontal and vertical directions allows one to obtain the selfcleaning effect of the sowing surface.
- Open Access
- 22 April 2015
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (1(74)) , 20-24
Industrial research of portal mixer-homogenizator
Industrial research of portal mixer-homogenizator
- 22 April 2015
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (1(74)) , 20-24
Open AccessIndustrial research of portal mixer-homogenizator
Industrial research of portal mixer-homogenizator
- 1 April 2015
- Published by Allerton Press in Coke and Chemistry
- Vol. 58 (4) , 147-149
Power consumed by a crusher rotor in overcoming atmospheric drag
Analytical formulas are developed for assessment of the influence of dusty air on the energy consumption in a hammer-type crusher applied to coal batch with a high content of fines. Analytical and experimental approaches are adopted. The ≤3 mm class present in the coal batch supplied for crushing forms a dust–air suspension, which is not crushed by hammer impact but significantly increases the drag on the rotor, with consequent increase in energy consumption. In overcoming the drag of the dust–air suspension, the energy consumption in the crusher may be 40% above the rated value. In that case, the removal of the ≤3 mm class from the feed to the crusher is necessary.
- 1 April 2015
- Published by Allerton Press in Coke and Chemistry
- Vol. 58 (4) , 147-149
Power consumed by a crusher rotor in overcoming atmospheric drag
Analytical formulas are developed for assessment of the influence of dusty air on the energy consumption in a hammer-type crusher applied to coal batch with a high content of fines. Analytical and experimental approaches are adopted. The ≤3 mm class present in the coal batch supplied for crushing forms a dust–air suspension, which is not crushed by hammer impact but significantly increases the drag on the rotor, with consequent increase in energy consumption. In overcoming the drag of the dust–air suspension, the energy consumption in the crusher may be 40% above the rated value. In that case, the removal of the ≤3 mm class from the feed to the crusher is necessary.