SSSerhii Shved

Serhii Shved

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Serhii Shved has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Establishment of regularities in the formation of the restoring force of a ball support system of a machine with an eccentric mass

    by Dmytro Popolov, Serhii Shved, Hennadii Zaitsev, Ihor Zaselskiy

    The object of research is the ball support system of a machine with an eccentric mass, which limits the transmission of horizontal dynamic loads to the foundation. The problem was not to transfer horizontal dynamic forces onto the foundation‚ thus stabilizing the machine without an increase in the structural mass of the equipment and guaranteeing adaptation to varying operating conditions․ For the analysis of the support design efficiency, a mathematical model of the restoring force depending on the weight of the machine, geometrical parameters of the support, and allowable displacement of the machine body was created. On the basis of this model, the nonlinear dependency of the restoring force and its linear approximation were obtained. Further analysis of their properties was conducted numerically by using the technical parameters of the KKD-1500/180 cone crusher. The investigation results indicate that the force which acts to restore depends only on the load caused by the weight of the machinery and the geometry of the spherical surface contacts. With the geometric coefficient of k = 1–1.5, the system has self-limited behavior in relation to the vibration amplitude of the machinery body. The analysis of the differences between the absolute values of the restoring forces obtained by both models and the relative error of the linearization demonstrated that, at low displacements δ ≤ 40 mm, the linearization error is less than 0.88%. Intermediate displacements δ = 40–80 mm and critical displacement δ = 150 mm have errors equal to 4.7% and 32%, respectively. In the last case, the linearization results in lower values of the restoring force. Thus, these relationships can be employed in the development of ball support systems that have spherical contact surfaces of machines that possess eccentric masses experiencing considerable horizontal dynamic load. When carrying out preliminary designs and during normal working conditions (δ ≤ 40 mm), the linear approximation may be regarded as sufficiently accurate. However, operating conditions close to resonance, resonance passage, and those concerning transient and emergency loads for displacements δ > 80 mm require the application of the nonlinear model.

  • Open Access

    Modeling of the deformed state of the screen box of a heavily loaded vibratory machine

    by D. V. Popolov, S. V. Shved, I. V. Zaselskyi, V. L. Velitchenko

    The paper addresses the problem of improving the technical and economic efficiency of heavily loaded vibratory machines through optimization of the load-bearing frame of the screen box. The main elements providing the spatial stiffness of the box structure are tubular transverse tie-beams, which operate under conditions of intensive cyclic bending loads. Analysis of the available literature indicates that these elements belong to the most highly loaded and vulnerable structural components, for which fatigue failure is the dominant failure mechanism. The traditional approach to increasing the strength of structural elements, namely, enlarging the cross-sectional area, leads to an increase in the mass of the screen box and the associated inertial loads, which adversely affects the dynamic characteristics of the vibratory machine. The objective of this study was to improve the structural efficiency of the screen box of a vibratory machine by optimizing the geometry of the tie-beams using a rational material distribution along the length of the element. An approach is proposed that involves varying the outer diameter of the tubular tie-beam according to a parabolic law while maintaining a constant inner diameter. Such an approach makes it possible to reduce the beam mass in regions of low bending moments while simultaneously maintaining or increasing stiffness in the most heavily loaded sections. To evaluate the effectiveness of the proposed solution, a series of numerical experiments was carried out using the finite element method. The simulations included calculations of axial compression, bending under transverse inertial loading, determination of the first natural frequency, and estimation of the critical buckling load for tie-beams with both baseline and parabolic profiles. The obtained results demonstrate that the use of a parabolic profile makes it possible to reduce the mass of the tie-beam by 41%, while the transverse acceleration corresponding to the onset of yielding increases by 55%, and the first natural frequency increases by 18%. Stress distribution maps indicate a more uniform loading of the material in the tie-beam with the parabolic profile. The deformed state of the screen box was also modeled using both the baseline and the optimized tie-beams. The results show that the change in beam geometry has virtually no effect on the dynamic characteristics of the box. The first natural frequency of the structure changes only slightly, while the deformation pattern and the maximum displacement amplitude remain practically unchanged. The obtained results confirm the prospects of applying variable-section tie-beams for improving the energy efficiency and reliability of vibratory machines.

  • Open Access

    Industrial studies of the operation of vibrating screening machines with an impact-action screening surface

    by D.V. Popolov, V.Y. Zaselskyi, O.D. Uchytel, S.V. Shved, I.V. Zaselskyi, K.YE. Zielova

    The modern development of the metallurgical industry is characterized by increasing requirements for energy efficiency and reduction of carbon emissions in line with the Green Steel transition and the European Green Deal. One of the key factors affecting blast furnace efficiency is the granulometric composition of burden materials, which determines gas-dynamic conditions and fuel consumption. Therefore, improving screening efficiency is an important scientific and practical task. The aim of the study is to determine the influence of a vibration-impact operating mode of vibrating screens on technological performance, stabilization of granulometric composition, and mechanical strength of agglomerate under industrial conditions. The methodology is based on industrial experiments carried out on vibrating screens with a freely supported sieve surface operating in a vibration-impact mode. The evaluation included transport capacity, screening efficiency, sieve clogging, particle strength, and synchronization of vibration exciters. The results show that the vibration-impact mode reduces transport capacity by 17…56%, while significantly improving process quality indicators. In particular, sieve clogging decreases by up to 6 times and screening efficiency increases by 43% compared to the conventional mode under identical dynamic parameters. It is established that stabilization of granulometric composition is most effective at vibration acceleration levels of 30…40 m/s², which allows reducing the content of the –5 mm fraction by 5%. Additionally, an increase in vibration acceleration by 11% leads to a 17% decrease in the phase shift of imbalance masses, indicating improved synchronization and reduced transient processes. The scientific novelty lies in the industrial confirmation of the effectiveness of the vibration-impact screening mode with a freely supported sieve surface. The practical significance consists in improving raw material preparation quality and reducing energy consumption in metallurgical processes. Further research should focus on optimization of design and operating parameters

  • Open Access

    Laboratory studies on the effect of vibro-impact action of the screening surface on the main technological indicators of metallurgical raw material screening

    by Dmytro Popolov, Serhii Shved, Hennadii Zaitsev, Serhii Henkulenko, Oleh Shumylo

    The article presents the results of a study on the effect of vibro-impact action of the screening surface on the main technological indicators of metallurgical raw material screening. The screening process is one of the key technological operations in the preparatory processes of metallurgical production, as it directly influences the quality of raw material fractionation and process productivity. The issue of screen aperture clogging significantly limits the productivity of screening, leading to a decrease in the quality of prepared charge. The purpose of the study is to investigate the effect of vibro-impact action of the screening surface on aperture clogging and the productivity indicators of metallurgical raw material screening. To achieve this goal, a laboratory model of a vibratory screener was developed, allowing for the simulation of various vibration modes of the box and studying their impact on the raw material screening process. The research methodology included a series of experiments with varying amplitude and angular frequency of box oscillations, analysis of the results using mathematical statistics methods, and the construction of mathematical models of the dependence of transportation productivity and clogging coefficient on vibration parameters. Experiments were conducted for two types of screening surfaces — fixed and freely laid, which allowed for assessing the impact of vibro-impact loads on screen aperture self-cleaning. The results showed that maximum transportation productivity is achieved at a forced oscillation amplitude of 2·10-3 m and an acceleration of 28…32 m/s². At the same time, the clogging coefficient significantly decreases at an amplitude of 1,8…2,2·10-3 m and an oscillation frequency of 94,2…102 s-1. The constructed mathematical models allow predicting changes in the technological parameters of the process depending on the dynamic characteristics of the box and assist in selecting optimal operating modes for vibratory screeners. The scientific novelty of the work lies in determining the effect of vibro-impact action on the productivity of the process of screening metallurgical raw material screening and forming new approaches to reducing screen surface clogging.


  • Open Access

    Analytical studies of the operation of a vertically directed vibratory-magnetic separator

    by Serhii Shved, Hennadii Zaitsev, Serhii Henkulenko, Oleh Shumylo

    The article discusses a new design and operation of a vertically directed vibration-magnetic separator intended for the disposal of iron-containing waste from mining and metallurgical enterprises. The problem of recycling iron-containing waste in Ukraine is quite acute and consists of large volumes, outdated processing technologies and equipment, and negative environmental impact. Outdated recycling technologies lead to soil, water and air pollution, as well as the loss of valuable secondary resources. An effective solution to the problem requires the introduction of modern technologies and equipment for processing accumulated iron-containing waste. The aim of the work is to study the processing and disposal of iron-containing waste using a new vertically directed vibration-magnetic separator. The main methods used in the work were analytical studies and mathematical modelling of processes occurring in a vertically directed vibration-magnetic separator. As a result of the research, the main patterns of the process of enrichment of iron-containing materials were obtained for the proposed design of the vibration-magnetic separator, which allows selecting rational and effective parameters of the technical system under consideration. The research results can be used to develop modern and effective equipment for the enrichment of iron-bearing waste from mining and metallurgical enterprises.

  • Open Access

    Modeling the movement of material along the rough surface of a mixer blade installed above a moving conveyor belt

    by Serhii Shved, Mariia Kozak, Tatiana Zaselska, Kateryna Zielova, Nataliia Dats

    The main methods of preparing the metallurgical charge for its further use today include the operation of mixing various materials with different granular composition to obtain a homogeneous mixture. For the preparation of metallurgical charge in the mining and metallurgical industry, continuous action mixers are used, which, unlike batch mixers, have a number of significant advantages, such as high productivity and the possibility of fully automating the process of preparing the necessary mixture. The well-known designs of mixers used in the preparation of metallurgical charge include drum, screw and rotary mixers. Recently, a lot of attention has been paid to rotary mixers, because they are the best among the mixers used in the preparation of metallurgical charge in terms of their main characteristics - productivity and energy consumption. But in a number of cases, rotary mixers do not meet the technological conditions for the preparation of a high-quality mixture. Therefore, increasing its efficiency when preparing the metallurgical charge for sintering or remelting requires a deeper analysis of the operation of the blade rotor, working in conjunction with the movement of the conveyor belt installed above it. Such analysis and research would allow to improve the mixing process to obtain a high-quality mixture of mineral raw materials when using a rotary mixer installed above a moving conveyor belt. Therefore, works aimed at establishing ways of improving this type of equipment are very interesting and relevant today. The paper describes the movement of material particles along the rough surface of the rotor blade of the mixer, which rotates in a layer of loose material transported simultaneously on the conveyor belt, and analyzed which main parameters affect the quality of the mixture preparation. As a result of research, a mathematical model was obtained for a horizontally-directed mixer with rotor cable elements that bring the material layer into a suspended state, which describes the influence of design and mode parameters on the nature of the movement of material particles in a pseudo-viscous medium. It was established that the nature of the movement of particles moving along with the conveyor belt can be considered stable.


  • Open Access

    Дослідження стійкості штабелеукладача при різних умовах його роботи

    by Volodymyr Zaselskyi, Serhii Shved, Dmytro Popolov, Hennadii Zaitsev, Katerina Zelova

    This article deals with the research related to the reengineering of stackers, which were developed and manufactured at the end of the twentieth century and are still in operation at a number of enterprises of the mining and metallurgical complex of Ukraine. For this study, we chose a modernized stacker type U1 SN-1200, which is still in operation at the iron ore pellets storage area of the pelletizing plant of the Central Mining and Processing Plant of Kryvyi Rih. Its modernization involved the removal of a very bulky, heavy outdated aspiration system, which could significantly affect the rollover stability of its platform and lead to the failure of both its individual components and the stacker as a whole. Therefore, the aim of the research was to conduct studies related to determination of the stacker's margin of safety against overturning depending on its design features that have emerged over the course of its operation and performance for materials whose bulk density does not exceed 1,9 t/m3. To achieve this goal, we used calculation and analytical methods in the MathCAD environment. The main source materials for calculations and research were archival drawings of the stacker and its technical passport. The research found that even with its nine-ton aspiration unit removed, the unit, which is significantly offset from the center of gravity of the entire structure, the safety margin of the stacker to overturning, depending on the capacity, is in the range of 1,6-1,9. Installation of an additional 9 t load instead of the aspiration unit, increases the safety margin of the stacker to 2,2, and without it to 1,8 at maximum stacker productivity of 1200 t/h.

  • Open Access

    Дослідження варіантів удосконалення ґрунтового насосу для залізорудної пульпи

    by Oleksandr Uchitel, Ihor Zaselskiy, Serhii Shved, Volodymyr Velitchenko, Mariia Kozak

    For pumping iron ore slurry, many mining and processing plants in Ukraine use an 8Gr-8m submersible pump. As shown its performance under the conditions of pumping pulp with a density of up to 1400 kg/m 3, they do not correspond to the passport data, and this is mainly due to concerns the flow chamber, the service life of which is reduced by almost 2 times compared to the manufacturer’s suggested service life. Therefore, the aim of the work was to study options for improving the design of the flow part of the 8Gr-8m pump, which would significantly increase its service life. To achieve this goal and obtain the required results we chose a method based on hydrodynamic studies using CAD technologies, for which, in addition to the 3D model of the existing pump, four more different designs were developed. The proposed designs were studied using SOLIDWORKS Flow Simulation program, which allowed us to model the movement of the pulp in the pump flow chamber. The parameters for modeling were selected based on pump operation conditions at the iron ore pulp pumping section concentrator of the Southern Mining and Processing Plant in Kryvyi Rih. The analysis of the results showed that the best performance is provided by a composite impeller with 4 blades of complex shape, low profile, which has a good pumping characteristic with a minimum tendency to wear. The design of the removable impeller is made of cast steel and lined with rubber, it has 4 blades with rounded front edges. The distance along the armhole between the side washers is 50 mm, it is unchanged. The pressure surface of the blade has a short ledge. The distribution zone is a high layer of small diameter. The inlet washer is flat, but with a high flap on the diffuser. The diameter of the wheel is 520 mm, and its weight is 70 kg. Based on this model, animproved design was proposed for of the flowing part of the 8GR-8m pump impeller and its lining lining based on SCS-30ARKM-15 rubber, which in combination with technical solutions allows to more effectively prevent wear of the studied unit and leads to increase its service life.

  • Open Access

    Modeling the horizontal movement of bulk material in the system “conveyor – rotary mixer”

    by Vladimir Zaselskiy, Sergey Shved, Mariia Shepelenko, Nataliia Suslo

    In this work, we consider methods for analytical construction of the profile of rotor blades mixer, as well as mathematical modeling of their work on moving and mixing bulk material on a conveyor to increase process efficiency mixing raw materials and optimizing its operating costs. In addition to increasing the effectiveness of the mixing process and lower operating costs, the goal of implementation the proposed methods is the consciousness of production with the least possible errors that would meet modern technical requirements and be adapted to consumer tasks. In this regard, the aim of this work was to determine rational parameters and geometric characteristics of the profile of the rotor mixer blades contributing to improving the quality of mixing the metallurgical charge transported on a conveyor belt. To achieve the goal by modeling, which is a key method of the fourth concept industrial revolution, using the developed mathematical model analyzed the movement of a particle of material along a conveyor belt with its subsequent interaction with the blades of the working body of the rotary mixer.


  • Open Access

    Studying of movement kinematics of dynamically active sieve

    by Dmitry Popolov, Sergey Shved, Igor Zaselskiy, Igor Pelykh

    The article presents the movement kinematics of the modular bar element of a dynamically active polymer sieve of a vibrating screen. On the basis of analytical methods, the mathematical model was obtained, which makes it possible to determine the law and trajectory of the modular bar element movement depending on its geometric characteristics, physico-mechanical properties of the polymer material, the regime and technological parameters of the vibrating screen. The results of this research show that in the working frequency range of the vibrating screen grate, modular bar element of the dynamically active sieve moves along the trajectories, the envelope of which is represented by Cassini’s ovals, which along with the generation of the amplitude component in the horizontal and vertical directions allows one to obtain the selfcleaning effect of the sowing surface.