Vanessa Meulenberg
Research Subjects
Research Interests
Vanessa Meulenberg has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Mats Ekevad
Department of Engineering Sciences and Mathematics, Division of Wood Science and Engineering, Skellefteå Campus, Luleå University of Technology, Skellefteå, Sweden
2 shared publications Mikael Svensson
Division of Wood Science and Engineering, Luleå University of Technology, Skellefteå, Sweden
2 shared publicationsClaus Weimann
HOSCH Fördertechnik GmbH
1 shared publicationHenrik Lindström
Predge AB
1 shared publication- Johan Öhman
Lulea Tekniska Universitet, 97187 Lulea
1 shared publication Mats Ekevad
Division of Wood Science and Engineering, Luleå University of Technology, Skellefteå, Sweden
1 shared publication
Latest Publications
- Open Access
- 27 June 2024
- Published by PHM Society in Phm Society European Conference
- Vol. 8 (1) , 7
Feasibility of Condition Monitoring of Belt Splices in Belt Conveyor Systems Using IoT Devices*
This paper investigates fully automated condition monitoring of belt splices within operational belt conveyor systems, using IoT devices to predict and inform on potential belt breakage or tearing. Such events cause production stops and potentially harm workers. Belt splices are laminated belt connections subject to deterioration during operation and are usually weak spots. The proposed scheme circumvents manual inspection efforts and uses the HOSCHiris DISCOVER IoT device for sensing and data acquisition. Each belt conveyor is equipped with one individual IoT device acquiring the motion signal of the scraper which is used to learn signal patterns of the pulley and the belt to identify both location and deterioration of the individual splices. Deterioration is characterized from an initial healthy condition to a severe condition of the splice to inform on the potential need for action. To assess the feasibility of the scheme, several tests are designed and performed in an industrial belt conveyor system. The results indicate that the scheme can provide valuable insights into the splice condition and its degradation.
- 27 June 2024
- Published by PHM Society in Phm Society European Conference
- Vol. 8 (1) , 7
Open AccessFeasibility of Condition Monitoring of Belt Splices in Belt Conveyor Systems Using IoT Devices*
This paper investigates fully automated condition monitoring of belt splices within operational belt conveyor systems, using IoT devices to predict and inform on potential belt breakage or tearing. Such events cause production stops and potentially harm workers. Belt splices are laminated belt connections subject to deterioration during operation and are usually weak spots. The proposed scheme circumvents manual inspection efforts and uses the HOSCHiris DISCOVER IoT device for sensing and data acquisition. Each belt conveyor is equipped with one individual IoT device acquiring the motion signal of the scraper which is used to learn signal patterns of the pulley and the belt to identify both location and deterioration of the individual splices. Deterioration is characterized from an initial healthy condition to a severe condition of the splice to inform on the potential need for action. To assess the feasibility of the scheme, several tests are designed and performed in an industrial belt conveyor system. The results indicate that the scheme can provide valuable insights into the splice condition and its degradation.
- Open Access
- 11 June 2022
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 80 (5) , 1165-1173
Minor cutting edge angles of sawing teeth: effect on cutting forces in wood
Optimising the cutting tool geometries can reduce waste while increasing timber yield. The industry is moving towards thin-kerf bandsawing of timber, and therefore, the geometry of the minor cutting edge and minor first flanks of cutting teeth become more important. Six cutting teeth with varying minor cutting edge angles ( $$0^{\circ }$$ , $$2^{\circ }$$ , $$4^{\circ }$$ , $$6^{\circ }$$ ) and minor cutting edge clearance angles ( $$2^{\circ }$$ , $$4^{\circ }$$ , $$6^{\circ }$$ ) were tested by cutting into the heartwood and sapwood of frozen and non-frozen Norway spruce (Picea abies (L.) Karst.) and Scots pine (Pinus sylvestris L.). Single cutting tooth tests were conducted, and the cutting and feeding forces were measured. The cutting forces were higher for Scots pine due to its higher density. Frozen sapwood resulted in higher cutting forces. The feeding force of frozen sapwood stood out as it was highly negative (i.e. self-feeding) compared to frozen heartwood, non-frozen heartwood and non-frozen sapwood. An increase in the minor cutting edge angle and minor cutting edge clearance angles, and therefore more room for elastic spring-back, can lead to up to less friction and 40% lower cutting forces. Higher minor cutting edge angles and minor cutting edge clearance angles resulted in less-negative feeding forces (i.e. less self-feeding) for frozen sapwood but remained relatively unchanged for the other wood conditions.- 11 June 2022
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 80 (5) , 1165-1173
Open AccessMinor cutting edge angles of sawing teeth: effect on cutting forces in wood
Optimising the cutting tool geometries can reduce waste while increasing timber yield. The industry is moving towards thin-kerf bandsawing of timber, and therefore, the geometry of the minor cutting edge and minor first flanks of cutting teeth become more important. Six cutting teeth with varying minor cutting edge angles ( $$0^{\circ }$$ , $$2^{\circ }$$ , $$4^{\circ }$$ , $$6^{\circ }$$ ) and minor cutting edge clearance angles ( $$2^{\circ }$$ , $$4^{\circ }$$ , $$6^{\circ }$$ ) were tested by cutting into the heartwood and sapwood of frozen and non-frozen Norway spruce (Picea abies (L.) Karst.) and Scots pine (Pinus sylvestris L.). Single cutting tooth tests were conducted, and the cutting and feeding forces were measured. The cutting forces were higher for Scots pine due to its higher density. Frozen sapwood resulted in higher cutting forces. The feeding force of frozen sapwood stood out as it was highly negative (i.e. self-feeding) compared to frozen heartwood, non-frozen heartwood and non-frozen sapwood. An increase in the minor cutting edge angle and minor cutting edge clearance angles, and therefore more room for elastic spring-back, can lead to up to less friction and 40% lower cutting forces. Higher minor cutting edge angles and minor cutting edge clearance angles resulted in less-negative feeding forces (i.e. less self-feeding) for frozen sapwood but remained relatively unchanged for the other wood conditions. - Open Access
- 19 March 2022
- Published by Springer Nature in Journal of Wood Science
- Vol. 68 (1) , 1-11
Minor cutting edge force contribution in wood bandsawing
As the sawmill industry is moving towards thinner bandsaws for higher yields, it is important to study the cutting force in more detail. The cutting force can be split into two zones. Zone I concerns the force on the major cutting edge as well as the friction force on the major first flank. Zone II considers the forces on the minor cutting edges as well as the friction forces on the minor first flanks. Zone II cutting can significantly affect the cutting force and has not been studied in great detail. Frozen, non-frozen and dry heartwood of Norway spruce and Scots pine were cut using different tooth geometries and the cutting force was measured. The major cutting edge, clearance, band thickness, minor cutting edge angle and minor cutting edge clearance angle were investigated. The y-intercept of the cutting force–width graph was used as the Zone II force (at this point the Zone I forces are assumed to be zero). The Zone II force contribution to the cutting force was studied. The results show that frozen wood has less elastic spring-back and therefore less Zone II cutting. Dried wood showed a significantly higher degree of Zone II cutting (55−75% contribution to the cutting force). Changing the major cutting edge from 2.87 mm to 1.6 mm resulted in 10–15% higher Zone II force contributions.
- 19 March 2022
- Published by Springer Nature in Journal of Wood Science
- Vol. 68 (1) , 1-11
Open AccessMinor cutting edge force contribution in wood bandsawing
As the sawmill industry is moving towards thinner bandsaws for higher yields, it is important to study the cutting force in more detail. The cutting force can be split into two zones. Zone I concerns the force on the major cutting edge as well as the friction force on the major first flank. Zone II considers the forces on the minor cutting edges as well as the friction forces on the minor first flanks. Zone II cutting can significantly affect the cutting force and has not been studied in great detail. Frozen, non-frozen and dry heartwood of Norway spruce and Scots pine were cut using different tooth geometries and the cutting force was measured. The major cutting edge, clearance, band thickness, minor cutting edge angle and minor cutting edge clearance angle were investigated. The y-intercept of the cutting force–width graph was used as the Zone II force (at this point the Zone I forces are assumed to be zero). The Zone II force contribution to the cutting force was studied. The results show that frozen wood has less elastic spring-back and therefore less Zone II cutting. Dried wood showed a significantly higher degree of Zone II cutting (55−75% contribution to the cutting force). Changing the major cutting edge from 2.87 mm to 1.6 mm resulted in 10–15% higher Zone II force contributions.
- Open Access
- 12 May 2021
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 16 (6) , 414-420
Thin kerf cutting forces of frozen and non-frozen Norway spruce and Scots pine wood
Reducing the kerf width in bandsawing has potential in reducing waste while optimising the yield. To be able to reduce the kerf width, understanding the cutting forces becomes critical. In this work, nine cutting teeth with varying band-body thicknesses and side clearances were tested by cutting both heartwood and sapwood of Norway spruce (Picea abies (L.) Karst.) and Scots pine (Pinus sylvestris L.) in frozen and non-frozen conditions. Single cutting teeth were moved into rotating wood samples in the 90–90° cutting direction, with chip thicknesses of 0.9 mm per cut. The main and normal cutting forces were measured. Scots pine had a higher density than Norway spruce and, therefore, a higher main cutting force. Non-frozen sapwood, non-frozen heartwood and frozen heartwood resulted in similar main cutting forces, but frozen sapwood resulted in significantly higher main cutting forces. Reducing the cutting width by about 45% resulted in an approximately 40% reduction in the main cutting force. The normal forces were not significantly affected by the species or cutting width. Frozen heartwood, non-frozen heartwood and non-frozen sapwood had similar normal cutting forces. Frozen sapwood had negative normal forces, and thus self-feeding was observed.
- 12 May 2021
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 16 (6) , 414-420
Open AccessThin kerf cutting forces of frozen and non-frozen Norway spruce and Scots pine wood
Reducing the kerf width in bandsawing has potential in reducing waste while optimising the yield. To be able to reduce the kerf width, understanding the cutting forces becomes critical. In this work, nine cutting teeth with varying band-body thicknesses and side clearances were tested by cutting both heartwood and sapwood of Norway spruce (Picea abies (L.) Karst.) and Scots pine (Pinus sylvestris L.) in frozen and non-frozen conditions. Single cutting teeth were moved into rotating wood samples in the 90–90° cutting direction, with chip thicknesses of 0.9 mm per cut. The main and normal cutting forces were measured. Scots pine had a higher density than Norway spruce and, therefore, a higher main cutting force. Non-frozen sapwood, non-frozen heartwood and frozen heartwood resulted in similar main cutting forces, but frozen sapwood resulted in significantly higher main cutting forces. Reducing the cutting width by about 45% resulted in an approximately 40% reduction in the main cutting force. The normal forces were not significantly affected by the species or cutting width. Frozen heartwood, non-frozen heartwood and non-frozen sapwood had similar normal cutting forces. Frozen sapwood had negative normal forces, and thus self-feeding was observed.