İnAn Ağir
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
İnAn Ağir has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Berkant Dindar
Department of Mechanical Engineering, Engineering and Architecture Faculty, Tokat Gaziosmanpaşa University, Tokat, Turkey
2 shared publications - Ali Kurşun
Department of Mechanical Engineering, Hitit University, Çorum, Turkey
1 shared publication - Cansu Var
Pamukkale University
1 shared publication Emre Kara
Department of Mechanical Engineering, Hitit University, Çorum, Turkey
1 shared publication- Ersin Demir
Department of Mechatronics Engineering, Pamukkale University, Denizli, Türkiye
1 shared publication - Görkem Gedik
Textile Engineering Department, Pamukkale University, Denizli, Turkey
1 shared publication
Latest Publications
- Open Access
- 30 June 2024
- Published by UCTEA Chamber of Textile Engineers in Tekstil ve Mühendis
- Vol. 31 (134) , 78-87
HEMP FIBER REINFORCED SUSTAINABLE “GREEN” COMPOSITE PRODUCTION WITH EPOXIDIZED SOYBEAN OIL
Due to the rising environmental concerns, industry branches are pushed to research and invest sustainable materials and technologies. In this context, this study aimed to combine a sustainable fiber and matrix material to produce green composite. For this purpose, epoxidized soybean oil and hemp fiber were utilized for composite production. Sebacic acid and maleic anhydride were used as hardeners. Histidine and glycerol were applied as accelerator and starter, respectively. Mechanical performance of the composites was evaluated by tensile and impact tests. Hemp fiber reinforcement resulted in improvement on tensile properties, up to 2.6 MPa tensile strength and 11.7 kJ/m2 impact strength. Thermal properties were determined by TGA and DSC analyses. The changes in molecular level after curing was traced with FTIR measurements and surface morphology was monitored with SEM imaging.
- 30 June 2024
- Published by UCTEA Chamber of Textile Engineers in Tekstil ve Mühendis
- Vol. 31 (134) , 78-87
Open AccessHEMP FIBER REINFORCED SUSTAINABLE “GREEN” COMPOSITE PRODUCTION WITH EPOXIDIZED SOYBEAN OIL
Due to the rising environmental concerns, industry branches are pushed to research and invest sustainable materials and technologies. In this context, this study aimed to combine a sustainable fiber and matrix material to produce green composite. For this purpose, epoxidized soybean oil and hemp fiber were utilized for composite production. Sebacic acid and maleic anhydride were used as hardeners. Histidine and glycerol were applied as accelerator and starter, respectively. Mechanical performance of the composites was evaluated by tensile and impact tests. Hemp fiber reinforcement resulted in improvement on tensile properties, up to 2.6 MPa tensile strength and 11.7 kJ/m2 impact strength. Thermal properties were determined by TGA and DSC analyses. The changes in molecular level after curing was traced with FTIR measurements and surface morphology was monitored with SEM imaging.
- 19 November 2023
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 31 (30) , 13412-13424
Effects of ceramic fillers on failure loads and failure mechanisms of laminated composites with two-parallel pin-loaded holes
- 19 November 2023
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 31 (30) , 13412-13424
Effects of ceramic fillers on failure loads and failure mechanisms of laminated composites with two-parallel pin-loaded holes
- 1 September 2021
- Published by Emerald Publishing in Emerging Materials Research
- Vol. 10 (3) , 295-299
Low-velocity impact response of Kevlar/epoxy aluminum laminates
In this experimental study, the low-velocity impact behavior of aluminum–Kevlar laminates (ARALL) was investigated. ARALL composites were prepared in two different configurations as aluminum–Kevlar–aluminum (AKA) and Kevlar–aluminum–Kevlar (KAK). The aluminum alloy used in the preparation of the samples was supplied as 5754 series 2 mm thick plates. Kevlar fabrics were supplied in a weight of 300 g/m2 and in twill weave type. Laminated composites with Kevlar twill fabrics were made through hand lay-up followed by the compression-molding process. [K]4 composite laminates were obtained by curing Kevlar/epoxy laminates under 100°C and 7 bar pressure for 180 min. Then, samples of size 100 × 100 mm were cut from the plates with a water jet. The cut specimens were bound together with two-component adhesive. An Instron Dynatup 9250 HV impact test device was used for impact tests. The energy profiling method was used, which expresses the impact energy and the corresponding absorbed energy. The increasing impact energy was performed on the two configurations of ARALL composites until perforation occurred. The perforation threshold of AKA samples was approximately 70% higher than that of KAK samples.
- 1 September 2021
- Published by Emerald Publishing in Emerging Materials Research
- Vol. 10 (3) , 295-299
Low-velocity impact response of Kevlar/epoxy aluminum laminates
In this experimental study, the low-velocity impact behavior of aluminum–Kevlar laminates (ARALL) was investigated. ARALL composites were prepared in two different configurations as aluminum–Kevlar–aluminum (AKA) and Kevlar–aluminum–Kevlar (KAK). The aluminum alloy used in the preparation of the samples was supplied as 5754 series 2 mm thick plates. Kevlar fabrics were supplied in a weight of 300 g/m2 and in twill weave type. Laminated composites with Kevlar twill fabrics were made through hand lay-up followed by the compression-molding process. [K]4 composite laminates were obtained by curing Kevlar/epoxy laminates under 100°C and 7 bar pressure for 180 min. Then, samples of size 100 × 100 mm were cut from the plates with a water jet. The cut specimens were bound together with two-component adhesive. An Instron Dynatup 9250 HV impact test device was used for impact tests. The energy profiling method was used, which expresses the impact energy and the corresponding absorbed energy. The increasing impact energy was performed on the two configurations of ARALL composites until perforation occurred. The perforation threshold of AKA samples was approximately 70% higher than that of KAK samples.
- 1 June 2021
- Published by Emerald Publishing in Emerging Materials Research
- Vol. 10 (2) , 139-144
Tensile and buckling properties of notched 6063 aluminum repaired with composite patches
In this study, 6063 aluminum plates with ‘O’ and ‘U’ notches were patched with E-glass/epoxy composites. In this context, O and U notches were made using an aluminum computer numerically controlled machine. Then, composite patches were produced through the hand lay-up method and hot-pressing. The 36 × 40 mm patches were water-jet-cut from E-glass/epoxy plates. The notched aluminum surfaces were cleaned with a rotary felt, and then solvent-based spray was applied and the surfaces were made ready for adhesion. Bonding was done with two-component Weicon RK-7100 adhesive. Tensile and buckling tests were performed under ambient conditions with an Instron 8801 test device. Experiments were carried out in O, U–O and U–O–U configurations without patches, one-side-patched and two-side-patched, and the results were presented comparatively in graphs.
- 1 June 2021
- Published by Emerald Publishing in Emerging Materials Research
- Vol. 10 (2) , 139-144
Tensile and buckling properties of notched 6063 aluminum repaired with composite patches
In this study, 6063 aluminum plates with ‘O’ and ‘U’ notches were patched with E-glass/epoxy composites. In this context, O and U notches were made using an aluminum computer numerically controlled machine. Then, composite patches were produced through the hand lay-up method and hot-pressing. The 36 × 40 mm patches were water-jet-cut from E-glass/epoxy plates. The notched aluminum surfaces were cleaned with a rotary felt, and then solvent-based spray was applied and the surfaces were made ready for adhesion. Bonding was done with two-component Weicon RK-7100 adhesive. Tensile and buckling tests were performed under ambient conditions with an Instron 8801 test device. Experiments were carried out in O, U–O and U–O–U configurations without patches, one-side-patched and two-side-patched, and the results were presented comparatively in graphs.
- 2 January 2016
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 2 (1) , 1-6
Impact response of sandwiches with open-cell casting metal foam and GFRP skins
The main advantage of using sandwich structures is their high strength, high energy absorbing capacity and high bending stiffness to weight ratio. Therefore, they are unique for the applications where the light-weight design philosophy is a crucial aspect. While sandwich structures with polymeric foams have been applied for many years, recently there is a growing interest on a new generation composite sandwiches with metallic foam core. In this study, the influence of pores per inch (ppi) of the foam on low-velocity impact response of the entire panel has been investigated. The glass fibre reinforced plastic (GFRP) skins produced by vacuum bagging technique in the study were easily bonded to the foam surfaces using a commercial adhesive in order to combine the composite sandwich panel. The low-velocity impact tests are performed to the sandwiches with the combination of two different magnesium (Mg) alloy foams (having 10 pores per inch (ppi) and 20 pores per inch), and carried out by a drop test machine with different values of impact velocity ranging from 1 to 10 m/s in order to analyse its effect. The main results of the impact tests are: force-displacement curves, peak force values, absorbed energy and influence of impact velocity.
- 2 January 2016
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 2 (1) , 1-6
Impact response of sandwiches with open-cell casting metal foam and GFRP skins
The main advantage of using sandwich structures is their high strength, high energy absorbing capacity and high bending stiffness to weight ratio. Therefore, they are unique for the applications where the light-weight design philosophy is a crucial aspect. While sandwich structures with polymeric foams have been applied for many years, recently there is a growing interest on a new generation composite sandwiches with metallic foam core. In this study, the influence of pores per inch (ppi) of the foam on low-velocity impact response of the entire panel has been investigated. The glass fibre reinforced plastic (GFRP) skins produced by vacuum bagging technique in the study were easily bonded to the foam surfaces using a commercial adhesive in order to combine the composite sandwich panel. The low-velocity impact tests are performed to the sandwiches with the combination of two different magnesium (Mg) alloy foams (having 10 pores per inch (ppi) and 20 pores per inch), and carried out by a drop test machine with different values of impact velocity ranging from 1 to 10 m/s in order to analyse its effect. The main results of the impact tests are: force-displacement curves, peak force values, absorbed energy and influence of impact velocity.